manuals.plus
SMC
SMC Compressed Air Preparation Filters: Stainless Steel AFF/AM/AMD Series
Datasheet for SMC models including: SMC, AFF DS, AM DS, AMD DS, AFF70DS, AFF80DS, AFF90DS, AM70DS, AM80DS, AM90DS, AMD70DS, AMD80DS, AMD90DS, Compressed Air Filter, Mist Separator, Stainless Steel Filter, Pneumatic Filter, Air Preparation, ISO 8573
ES30-27A-AFFS Link Link 出力PDF Catalog AFF DS AM DS AMD DS Series - Compressed Air Preparation Filter Stainless Steel Type
ES30-27-AFFS Compressed Air Preparation Filter
Stainless Steel Type
D epends on the size and max. operating pressure
Improved environmental resistance with the stainless steel exterior
Main Line Filter AFF DS Series
1
Water droplet
m
removal
Mist Separator AM DS Series
0.1
m
Oil mist separation and removal
Micro Mist Separator AMD DS Series
0.01
Oil mist separation
m and removal
Flow capacity
14.51 m3/min (ANR)
AFF
1 For AFF90DS/AM90DS/AMD90DS
Pressure drop
AM AMD
5 kPa or less
AFF DS/AMDS/AMDDS Series
CAT.ES30-27A
Compressed Air Preparation Filter Stainless Steel Type AFFDS/AMDS/AMDDS Series
Variations
Series
AFFDS Series
Main Line Filter
Large dust particle filtration, Water droplet
separation
Gray
Water droplet removal ratio: 99%
Nominal filtration rating: 1 m [Filtration efficiency: 99%]
AMDS Series
Mist Separator
Dust filtration, Oil mist separation
Nominal filtration rating: 0.1 m [Filtration efficiency: 99%]
Light blue
Oil mist concentration on the outlet side:
Max. 1.0 mg/m3 (ANR) [ 0.8 ppm]
AMDDS Series
Micro Mist Separator
Dust filtration, Oil mist separation Nominal filtration rating: 0.01 m [Filtration efficiency: 99.9%] Oil mist concentration on the outlet side: Max. 0.1 mg/m3 (ANR) [ 0.08 ppm]
Blue
Port size Size
1 1 1/2 2 70 80 90 70 80 90 70 80 90
Flow capacity [m3/min (ANR)]
7.0 11.0 14.5
7.0 11.0 14.5
7.0 11.0 14.5
Easier replacement of the element
The stopper function prevents the bowl from falling.
The bowl will not fall even if the bolts are loosened. It is not necessary to hold the bowl when removing the bolts. Safe and secure mounting and removing of the bowl with both hands is possible. The lightweight stainless bowl with reduced thickness allows for easier element replacement.
1 Loosen the 4 securing bolts.
2 Rotate the bowl to release the stopper. Pull it down to remove the bowl.
3 At least 40 mm of maintenance space is necessary for removing the bowl.
Bolt
Stainless steel bowl
Flange drop prevention stopper
Minimum maintenance space
40 mm
1
Compressed Air Preparation Filter Stainless Steel Type AFFDS/AMDS/AMDDS Series
Can be identified by color
The type of element can be identified by the color of the end cap.
An end cap with slits is used for the element.
This eliminates the accumulation of condensate. Even high-velocity fluid is not spattered. The result is a compact bowl design. Slit
With slit
Without slit
Element
Element
Gray AFFDS
Light blue AMDS
Blue AMDDS
End cap with slits
Condensate
End cap
discharged Condensate without slits
Condensate is not accumulated, so no water flows to the downstream side.
Accumulated condensate flows to the downstream side.
Branch port
Mounting a sensor, etc., allows for element differential pressure management.
Branch port 2 x 1/4
Branch port plug
Insert the included plug with a square head when not in use.
Related Product
Pressure Sensor PSE560 Series
· Piping port/Parts in contact with fluid: Stainless steel 316L
· IP65
Scan or click here.
Details on differential pressure
management can be found here.
Compliant with ISO 8573 Compressed Air Purity Class
Systems which are in compliance with the degree of purity required for compressed air (For details p. 9)
Purity class as a system
Particles
Liquid water
Oil
4
7
4
Compressed air [ 6 : 8 : 4 ]
Main Line Filter AFF
Mist Separator
2
7
3
AM
Micro Mist
Separator
1
7
2
AMD
The class indicates the compressed air purity according to ISO 8573-1:2010 (JIS B 8392-1:2012) and indicates the maximum purity class which can be obtained using that system. Note, however, that this value will differ according to the inlet air conditions.
2
Compressed Air Preparation Filter Refer to the CE/UKCA-compliance list below.
Stainless Steel Type
AFFDS/AMDS/AMDDS Series
How to Order
AFF 70 D S 10 J P1
Symbol AFF
Description
Main line filter
Filter type
Specifications
Nominal filtration rating: 1 m Water droplet removal ratio: 99% or more
AM
Mist
Nominal filtration rating: 0.1 m
separator Oil mist density at outlet: 1.0 mg/m3
AMD
Micro mist separator
Nominal filtration rating: 0.01 m Oil mist density at outlet: 0.1 mg/m3
Symbol
Main line filter
1
2
L
Mist separator Micro mist separator
1
2
L
Body size
Symbol Flow capacity 70 7 m3/min (ANR) 80 11 m3/min (ANR) 90 14.5 m3/min (ANR)
Stainless steel type
Thread type
Symbol Type
Nil Rc
F
G
N NPT
Accessory4, 5
Symbol
Description
P1
With branch port plug
4 The branch port plug is a plug with a square head.
5 2 plugs are included and shipped with the product, but they do not come assembled.
Drain exhaust
Symbol J1
V2, 3
Description Drain guide Drain cock (Ball valve + Nipple)
1 Without a valve function 2 The drain cock comes together with the product,
but it does not come assembled. 3 It cannot be used in combination with "J."
Port size
Symbol
Port size
10
1
14 1 1/2
20
2
Applicable body size
70 80 90
--
--
--
--
--
--
CE/UKCA-compliant
Model
Max. operating pressure 1.0 MPa 1.6 MPa
AFF/AM/AMD70DS
--
--
AFF/AM/AMD80DS
--
AFF/AM/AMD90DS
Replacement Parts
Description
End cap color
For AFF Element For AM
For AMD
Gray Light blue
Blue
70 AFF-EL70DS AM-EL70DS AMD-EL70DS
Order no. 80
AFF-EL80DS AM-EL80DS AMD-EL80DS
90 AFF-EL90DS AM-EL90DS AMD-EL90DS
Contact SMC if degreasing treatment is required.
3
AFF DS/AMDS/AMDDS Compressed Air Preparation Filter Stainless Steel Type
Series
Main Line Filter AFF Series
Standard Specifications
Model
Port size
Fluid
Ambient and fluid temperatures
Proof pressure
Max. operating pressure
Min. operating pressure
Nominal filtration rating2
Water droplet removal ratio3
Max. flow capacity4
Compressed air purity class5
Weight [kg]
Material
Body7 Bowl7
°C MPa MPa MPa m
% m3/min (ANR)
AFF70DS 1
7.0 4.6
AFF80DS 1 1/2 Air
-5 to 60 (No freezing) 1.5 (2.41) 1.0 (1.61) 0.1
1.0 (Filtration efficiency: 99%) 99 11.0
ISO 8573-1:2010 [4 : 7 : 4]6 7.3
Stainless steel
AFF90DS 2
14.5 8.2
When the max. flow capacity is converted into the compressor discharge air volume
Model Max. flow capacity8
m3/min
AFF70DS 7.3
AFF80DS 11.5
AFF90DS 15.1
1 When selecting option J. 2 Filtration efficiency under the conditions below [Test condition ISO 8573-4:2001, Test method ISO 12500-3:2009 compliant]
At 0.7 MPa inlet pressure and max. flow capacity When the air flow capacity, inlet pressure, and the amount of solid or liquid particles on the filter inlet side are stable. When a new element is used 3 Water droplet removal rate under the conditions below [Test method ISO 12500-4:2009 compliant] At 0.7 MPa inlet pressure and max. flow capacity Water droplet on the filter inlet side = 33 g/m3
(Water droplet indicates condensed moisture. Water vapor which is not condensed is not included.)
When the air flow capacity, inlet pressure, and the amount of water droplets on the filter inlet side are stable. When a new element is used 4 Flow at 20°C, atmospheric pressure, and 65% of the relative humidity 5 The compressed air purity class is indicated based on ISO 8573-1:2010 Compressed air Part 1: Contaminants and purity classes. 6 The compressed air quality class on the inlet side is [ 6 : 8 : 4 ]. 7 Due to the production process, the product may have scratches, rubbing, stains, or discoloration that do not affect its function or performance. 8 The compressor discharge air volume is the flow rate converted into atmospheric pressure (compressor intake condition) at 32°C.
Pressure drop [kPa] Pressure drop [kPa] Pressure drop [kPa]
Flow Rate Characteristics
AFF70DS
18
16 14 Inlet pressure 0.3 MPa
12
10 Maximum ow capacity line 8 Inlet pressure 0.5 MPa 6
4
2 Inlet pressure 0.7 MPa
0 0123456 78 Air ow rate [m3/min (ANR)]
AFF80DS
9
8 7 Inlet pressure 0.3 MPa
6
5 Maximum ow capacity line
4 Inlet pressure 0.5 MPa
3
2
1 Inlet pressure 0.7 MPa
0 0 1 2 3 4 5 6 7 8 9 10 11 12 Air ow rate [m3/min (ANR)]
AFF90DS
7
6 Inlet pressure 0.3 MPa
5
4 Maximum ow capacity line
3 Inlet pressure 0.5 MPa
2
1 Inlet pressure 0.7 MPa
0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Air ow rate [m3/min (ANR)]
4
AFFDS/AMDS/AMDDS Series
Mist Separator AM Series
Standard Specifications
Model
Port size
Fluid
Ambient and fluid temperatures
Proof pressure
Max. operating pressure
Min. operating pressure
Nominal filtration rating2
Oil mist concentration on the outlet side3
Max. flow capacity4
Compressed air purity class5
Weight [kg]
Material
Body7 Bowl7
°C MPa MPa MPa m mg/m3 (ANR) m3/min (ANR)
AM70DS 1
7.0 4.6
AM80DS 1 1/2 Air
-5 to 60 (No freezing) 1.5 (2.41) 1.0 (1.61) 0.1
0.1 (Filtration efficiency: 99%) 1 ( 0.8 ppm) or less 11.0
ISO 8573-1:2010 [2 : 7 : 3]6 7.3
Stainless steel
AM90DS 2
14.5 8.2
When the max. flow capacity is converted into the compressor discharge air volume
Model Max. flow capacity8
m3/min
AM70DS 7.3
AM80DS 11.5
AM90DS 15.1
1 When selecting option J. 2 Filtration efficiency under the conditions below [Test condition ISO 8573-4:2001, Test method ISO 12500-3:2009 compliant]
At 0.7 MPa inlet pressure and max. flow capacity When the air flow capacity, inlet pressure, and the amount of solid or liquid particles on the filter inlet side are stable. When a new element is used 3 Oil mist concentration on the outlet side under the conditions below [Test condition ISO 8573-2:2007, Test method ISO 12500-1: 2007 compliant] At 0.7 MPa inlet pressure and max. flow capacity Oil mist concentration on the filter inlet side = 10 mg/m3 When the air flow capacity, inlet pressure, and the amount of water droplets on the filter inlet side are stable. When a new element is used 4 Flow at 20°C, atmospheric pressure, and 65% of the relative humidity 5 The compressed air purity class is indicated based on ISO 8573-1:2010 Compressed air Part 1: Contaminants and purity classes. 6 The compressed air quality class on the inlet side is [ 4 : 7 : 4 ]. 7 Due to the production process, the product may have scratches, rubbing, stains, or discoloration that do not affect its function or performance. 8 The compressor discharge air volume is the flow rate converted into atmospheric pressure (compressor intake condition) at 32°C.
Pressure drop [kPa] Pressure drop [kPa] Pressure drop [kPa]
Flow Rate Characteristics
AM70DS
20
18
16 Inlet pressure 0.3 MPa
14
12 Maximum ow capacity line
10
8 Inlet pressure 0.5 MPa
6
4
2
Inlet pressure 0.7 MPa
0 01234 567 8
Air ow rate [m3/min (ANR)]
5
AM80DS
10
9
8 Inlet pressure 0.3 MPa
7
6 Maximum ow capacity line
5
4 Inlet pressure 0.5 MPa
3
2
1
Inlet pressure 0.7 MPa
0 0 1 2 3 4 5 6 7 8 9 10 11 12
Air ow rate [m3/min (ANR)]
AM90DS
10
9
8
Inlet pressure 0.3 MPa
7
6 Maximum ow capacity line
5
4 Inlet pressure 0.5 MPa 3
2
1
Inlet pressure 0.7 MPa
0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Air ow rate [m3/min (ANR)]
AFF DS/AMDS/AMDDS Compressed Air Preparation Filter Stainless Steel Type
Series
Micro Mist Separator AMD Series
Standard Specifications
Model
Port size
Fluid
Ambient and fluid temperatures
Proof pressure
Max. operating pressure
Min. operating pressure
Nominal filtration rating2
Oil mist concentration on the outlet side3
Max. flow capacity5
Compressed air purity class6
Weight [kg]
Material
Body8 Bowl8
°C MPa MPa MPa m mg/m3 (ANR) m3/min (ANR)
AMD70DS 1
7.0 4.6
AMD80DS 1 1/2 Air
-5 to 60 (No freezing) 1.5 (2.41) 1.0 (1.61) 0.1
0.01 (Filtration efficiency: 99%) 0.1 ( 0.08 ppm) or less4 11.0
ISO 8573-1:2010 [1 : 7 : 2]7 7.3
Stainless steel
AMD90DS 2
14.5 8.2
When the max. flow capacity is converted into the compressor discharge air volume
Model Max. flow capacity9
m3/min
AMD70DS 7.3
AMD80DS 11.5
AMD90DS 15.1
1 When selecting option J. 2 Filtration efficiency under the conditions below [Test condition ISO 8573-4:2001, Test method ISO 12500-3:2009 compliant]
At 0.7 MPa inlet pressure and max. flow capacity When the air flow capacity, inlet pressure, and the amount of solid or liquid particles on the filter inlet side are stable. When a new element is used 3 Oil mist concentration on the outlet side under the conditions below [Test condition ISO 8573-2:2007, Test method ISO 12500-1: 2007 compliant] At 0.7 MPa inlet pressure and max. flow capacity Oil mist concentration on the filter inlet side = 10 mg/m3 When the air flow capacity, inlet pressure, and the amount of water droplets on the filter inlet side are stable. When a new element is used 4 0.01 mg/m3 ( 0.008 ppm) or less in the initial state 5 Flow at 20°C, atmospheric pressure, and 65% of the relative humidity 6 The compressed air purity class is indicated based on ISO 8573-1:2010 Compressed air Part 1: Contaminants and purity classes. 7 The compressed air quality class on the inlet side is [ 2 : 7 : 3 ]. 8 Due to the production process, the product may have scratches, rubbing, stains, or discoloration that do not affect its function or performance. 9 The compressor discharge air volume is the flow rate converted into atmospheric pressure (compressor intake condition) at 32°C.
Pressure drop [kPa] Pressure drop [kPa] Pressure drop [kPa]
Flow Rate Characteristics
AMD70DS
20
18
16 Inlet pressure 0.3 MPa
14
12 Maximum ow capacity line
10
8 Inlet pressure 0.5 MPa
6
4
2
Inlet pressure 0.7 MPa
0 01 2 3 4 56 78
Air ow rate [m3/min (ANR)]
AMD80DS
12
10 Inlet pressure 0.3 MPa
8
6 Maximum ow capacity line
4 Inlet pressure 0.5 MPa
2 Inlet pressure 0.7 MPa
0 0 1 2 3 4 5 6 7 8 9 10 11 12 Air ow rate [m3/min (ANR)]
AMD90DS
10
9
8 Inlet pressure 0.3 MPa
7
6 Maximum ow capacity line
5
4 Inlet pressure 0.5 MPa
3
2
1
Inlet pressure 0.7 MPa
0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Air ow rate [m3/min (ANR)]
6
AFFDS/AMDS/AMDDS Series
Dimensions: AFF, AM, AMD
Branch port plug IN
A EF
C
H
2 x 1/4 OUT
J
D
2 x P (Port size)
B
Maintenance
space
3/8
Dimensions
Model
P
A
C
D
E
AFF70DS/AM70DS/AMD70DS
1
144
21.3
68.7
35
AFF80DS/AM80DS/AMD80DS 1 1/2
170
30.3
80.7
45
AFF90DS/AM90DS/AMD90DS
2
170
36.6
80.7
45
The thread type for each port will be the same as the selected thread type.
Model
AFF70DS/AM70DS/AMD70DS AFF80DS/AM80DS/AMD80DS AFF90DS/AM90DS/AMD90DS
7
[mm]
Drain exhaust
Drain cock
Drain guide
Rc, NPT
G
B
B
B
350.7
410.5
414.5
356.7
416.5
420.5
422.4
482.2
486.2
G
Drain cock
B
3/8
[mm]
F
G
H
J
35
40
34.3
68.7
45
40
43.3
80.7
45
40
49.6
80.7
AFF DS/AMDS/AMDDS Series Specific Product Precautions
Be sure to read this before handling the products. Refer to the back cover for safety instructions. For air preparation equipment precautions, refer to the "Handling Precautions for SMC Products" and the "Operation Manual" on the SMC website: https://www.smcworld.com
Air Supply
Caution
1. This product is not applicable to gases other than compressed air. This product is not applicable to gases other than compressed air (example: oxygen, hydrogen, flammable gas, mixed gas).
2. Do not use compressed air that contains chemicals, organic solvents, salt, or corrosive gases. Do not use compressed gas containing chemicals, organic solvents, salt, or corrosive gas. This can cause rust, damage to rubber and resin parts, or malfunction.
Maintenance
Caution
1. Compressed air over the max. flow capacity line may not meet the specifications of the product. Select a model that is either at or under the max. flow capacity line.
8
International Standard ISO 8573-1:2010
Compressed Air Purity Classes
Compressed air is used in a variety of manufacturing processes. In this age, compressed air with a high degree of purity is becoming increasingly necessary. For this reason, it is necessary to remove contaminants from systems which supply compressed air and to secure the quality. The standard which stipulates the class according to the quantities of contaminants in compressed air is ISO 8573-1.
[Outline] Stipulates the purity class of contaminants (particles, water, oil) mixed in with the compressed air
[Scope] Can be used in various places in compressed air systems
[Purity Classes]
[Terms and Definitions]
· Purity class: An index assigned for each classification obtained by dividing the concentration of each contaminant into ranges
· Particle: Small discrete mass of solid or liquid matter · H umidity and liquid water: Water vapor (gas), Water
droplets · Oil: Liquid oil, Oil mist, Vapor
Particles
Humidity and liquid water
Oil
Class Maximum number of particles per cubic meter as a function of particle size d [m] Mass concentration Cp Pressure dew point Concentration of liquid water Cw Concentration of total oil
0.1 < d 0.5
0.5 < d 1.0
1.0 < d 5.0
[mg/m3]
[°C]
[g/m3]
[mg/m3]
0
As specified by the equipment user or supplier and more stringent than class 1
1
20000
400
10
--
-70
--
0.01
2
400000
6000
100
--
-40
--
0.1
3
--
90000
1000
--
-20
--
1
4
--
--
10000
--
+3
--
5
5
--
--
100000
--
+7
--
--
6
--
--
--
0 < Cp 5
+10
--
--
7
--
--
--
5 < Cp 10
--
Cw 0.5
--
8
--
--
--
--
--
0.5 < Cw 5
--
9
--
--
--
--
--
5 < Cw 10
--
x
--
--
--
Cp > 10
--
Cw > 10
> 5
[How to Perform a Test to Check the Performance] ISO 12500, which sets out the test method to be used in order to check the filter performance for each of the three kinds of contaminants, is indicated below. · Particle: ISO 12500-3:2009 · Liquid water: ISO 12500-4:2009 · Oil: ISO 12500-1:2007 Measured using a dedicated evaluation system which has been certified according to ISO 12500- and also by a third
party (Certified)
[Purity Class Designation Example]
ISO 8573-1:2010 [ 4 : 6 : 2 ]
Particle class 4 1.0 m < d Particles of 5.0 m 10000 particles/m3
Oil class 2 Concentration of total oil 0.1 mg/m3
Humidity and liquid water class 6 Pressure dew point +10°C
List of systems which conform to the degree of purity required for compressed air
Purity class as a system
Particles
Liquid water
Oil
4
7
4
Compressed air [ 6 : 8 : 4 ]
Line Filter AFF
2
7
3
Mist Separator
AM
Micro Mist
Separator
1
7
2
AMD
The class indicates the compressed air purity according to ISO 8573-1:2010 (JIS B 8392-1:2012) and indicates the maximum purity class which can be obtained using that system. Note, however, that this value will differ according to the inlet air conditions.
9
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of "Caution," "Warning" or "Danger." They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)1), and other safety regulations.
Danger : Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
Warning: Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
1) ISO 4414: Pneumatic fluid power - General rules and safety requirements for systems and their components ISO 4413: Hydraulic fluid power - General rules and safety requirements for systems and their components IEC 60204-1: Safety of machinery - Electrical equipment of machines - Part 1: General requirements ISO 10218-1: Robots and robotic devices - Safety requirements for industrial robots - Part 1:Robots etc.
Caution: Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications. Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment.
2. Only personnel with appropriate training should operate machinery and equipment. The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/ equipment until safety is confirmed. 1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. SMC products cannot be used beyond their specifications. They are not developed, designed, and manufactured to be used under the following conditions or environments. Use under such conditions or environments is not allowed. 1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight.
2. Use for nuclear power, railways, aviation, space equipment, ships, vehicles, military application, equipment affecting human life, body, and property, combustion equipment, entertainment equipment, emergency shut-off circuits, press clutches, brake circuits, safety equipment, etc., and use for applications that do not conform to standard specifications such as catalogs and operation manuals.
3. Use for interlock circuits, except for use with double interlock such as installing a mechanical protection function in case of failure. Please periodically inspect the product to confirm that the product is operating properly.
Caution
SMC develops, designs, and manufactures products to be used for automatic control equipment, and provides them for peaceful use in manufacturing industries. Use in non-manufacturing industries is not allowed. Products SMC manufactures and sells cannot be used for the purpose of transactions or certification specified in the Measurement Act of each country. The new Measurement Act prohibits use of any unit other than SI units in Japan.
Limited warranty and Disclaimer/ Compliance Requirements
The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance Requirements". Read and accept them before using the product.
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is first.2) Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalog for the particular products.
2) Suction cups (Vacuum pads) are excluded from this 1 year warranty. A suction cup (vacuum pad) is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the suction cup (vacuum pad) or failure due to the deterioration of rubber material are not allowed by the limited warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipment of a SMC product to another country, assure that all local rules governing that export are known and followed.
Safety Instructions Be sure to read the "Handling Precautions for SMC Products" (M-E03-3) and "Operation Manual" before use.
https://www.smcworld.com
Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
D-G
© 2025 SMC Corporation All Rights Reserved
Link Link1.0.0（ 26 ) MacOS DynaPDF 4.0.100.285 Related Documents
SMC Mist Separator Operation Manual
SMC Pneumatic Recommendations for Efficient and Safe Machine Operation & Energy Saving
SMC Basic Pneumatics: A Comprehensive Guide to Fluid Power Components and Applications
SMC IDFA E/F Series Refrigerated Air Dryers: Specifications, Options, and Selection Guide
SMC HRS-PF005 Particle Filter Set - Installation and Operation Guide
SMC Corporate Guide: Automatic Control Equipment and Pneumatic Solutions
SMC KFG2 Series Stainless Steel 316 Insert Fitting Operation Manual
SMC 25A-Series: Pneumatic Components for Secondary Battery Manufacturing
