XtremepowerUS DE Filter Replacement Grid Set

Product Information

Introduction

The XtremepowerUS D.E. Filter Replacement Grid Set is designed for maintaining crystal-clear pool water, providing superior filtration for clean and pure water with every swim. Crafted with high-quality materials, this replacement grid integrates seamlessly with D.E. filter systems, ensuring straightforward and hassle-free installation. Its robust construction minimizes the need for frequent replacements while enhancing filtration performance. The unique design maximizes filtration area for efficient capture of dirt and debris, leading to less maintenance and more enjoyment. It serves as an upgrade for pool cleanliness and peace of mind.

With the XtremepowerUS D.E. Filter Replacement Grid, users can expect:

• Enhanced filtration for sparkling clean water.
• Easy installation with a perfect fit for D.E. filter systems.
• Durable construction that withstands regular use.
• Cost-effective maintenance due to long-lasting materials.

Packaging Contents

• Instruction Manual: 1 PC(S)
• Part #1 Small Replacement Grid: 1 PC(S)
• Part #2 Large Replacement Grid: 7 PC(S)

SKU: 75207 (Fits 60 FT DE Filter), SKU: 75208 (Fits 48 FT DE Filter)

Important Safety Instructions

This guide provides instructions for installing and using the DE Filter Replacement Grid Set. For any questions regarding the equipment, please contact XtremepowerUS.

This guide contains crucial information for the safe installation and operation of this product. After installation, ensure this information is shared with the owner/operator or left with them for their reference.

Legends and Symbols

When encountering safety-alert symbols in the equipment or manual, pay attention to the following signal words and remain vigilant about the potential for personal injury:

DANGER: Ignoring these hazards can result in death, severe personal injury, or significant property damage.

WARNING: Indicates potential hazards that can result in severe personal injury, death, or significant property damage. Ignoring these warnings presents a real danger.

CAUTION: Indicates potential hazards that can result in minor or moderate personal injury, property damage, or actions that are unpredictable and unsafe. Ignoring these cautions presents a potential hazard.

NOTICE: This label indicates important special instructions that are not directly related to hazards.

USE OF NON-XTREMEPOWERUS REPLACEMENT PARTS VOIDS WARRANTY

ATTENTION INSTALLER: This manual contains vital information regarding the installation, operation, and safe use of this product. It is essential to provide this manual to the end user. Failure to read and follow all instructions could lead to severe injuries.

DANGER Failure to comply with all instructions and warnings may lead to severe bodily injury or even death. For optimal safety and functionality, it is advisable to have the product installed and serviced by a certified service professional. Prior to using this product, installers, operators, and owners must carefully review these warnings and all instructions provided in the owner's manual. It is essential to leave these warnings and the owner's manual with the owner for their reference and safety.

WARNING For safety reasons, children should not be allowed to use this product. Packing materials and plastic bags are not toys. Keep them away from children to prevent the risk of suffocation.

Assembly Instructions

Step 1: Verify Grid Size

Verify that the replacement grids' size matches the original ones from the filter.

Diagrams illustrate the dimensions (Height and Width) for the small and large replacement grids.

Step 2: Backwash Filter

Perform a backwash to remove old D.E. and debris, facilitating a cleaner grid change.

Illustration of a filter valve and backwash port, with an arrow indicating rotation [rotate clockwise] for backwashing.

Step 3: Open Air Relief Valve

Flush out water from the filter's tank and plumbing by opening the filter's pressure gauge or valve.

Pressure gauge on the filter tank. Arrow indicates rotating valve [rotate counter-clockwise] to open.

Step 4: Drain Tank

Remove the filter's drain cap for water evacuation.

Close-up of the filter's drain cap. Arrow indicates rotating the cap [rotate counter-clockwise] to remove.

Step 5: Power Shutdown

Ensure all equipment's power is disconnected at the breaker.

Electrical box with power switch in the 'OFF' position.

Step 6: Detach Clamp Assembly

Remove the bolt and nut from the filter's clamp assembly, then remove the whole clamp.

Filter tank clamp with bolt and nut. Arrow indicates rotating nut [rotate counter-clockwise] to loosen.

Step 7: Lift Tank Lid

Remove the upper filter body and set it aside for reinstallation later.

Upper filter body being lifted from the lower filter body.

Step 8: Extract Grid Assembly

Lift the grid assembly from the filter's tank. Detach the manifold cap from the top of the manifold.

Grid assembly lifted from the filter tank. Manifold cap detached from the manifold.

Step 9: Disassemble Grid Assembly

Detach the manifold from the tie rod by unscrewing the securing nut, preparing for individual grid inspection or replacement.

Manifold nut unscrewed from the tie rod. Disassembled grid assembly showing retainer and tie rod screw.

Step 10: Inspect and Select Grids

Evaluate grids for damage, removing only those necessary or replace the entire set as needed.

Visual of seven large grids and one small grid.

Step 11: Clean Tank

Wash out any residual D.E. powder or debris, ensuring the lower filter body and gasket grooves are clean.

Spray nozzle cleaning the interior and gasket grooves of the lower filter body.

Step 12: Assemble New Grids

Place the manifold on a stable surface, then sequentially install grids into the manifold, starting with the smaller grid at the standpipe port.

Manifold with standpipe port, and a small grid being inserted.

Step 13: Install Grid Retainer

Align the grid retainer and top standpipe manifold port, ensuring correct grid placement.

Grid retainer aligned with the standpipe manifold port.

Step 14: Insert Tie Rod

Insert the tie rod through the retainer and manifold.

Tie rod (screw) inserted through the grid retainer and manifold.

Step 15: Position Grid Assembly Upright

Flip the grid assembly to an upright position, ensuring both the retainer and manifold are held securely.

Assembled grid structure positioned upright.

Step 16: Fasten Tie Rod

Attach the tie rod nut to secure the manifold at the assembly's top. Attach the manifold cap to the top of the manifold.

Tie rod nut attached to secure the manifold; manifold cap placed on top.

Step 17: Position New Grid Assembly

Align and install the grid assembly within the lower filter body, ensuring proper standpipe alignment, then reassemble the manifold cap onto the top of the manifold.

Grid assembly installed into the lower filter body.

Step 18: Place Tank Lid

Reattach the upper filter body, maintaining the o-ring in its designated groove.

Upper filter body placed back onto the lower filter body, with O-ring seated.

Step 19: Attach Clamp Assembly

Evenly position the clamp assembly, and securely fasten the bolt and nut.

Clamp assembly fitted around the filter tank. Bolt and nut shown; arrow indicates rotation [rotate clockwise] to tighten.

Step 20: Attach Drain Plug

Secure the filter's drain plug.

Filter's drain plug secured with rotation [rotate clockwise].

Step 21: Leak Testing

Fasten and secure the filter's pressure gauge or valve. Activate the pump for priming, checking for leaks and ensuring proper seal alignment if leaks are present.

Pressure gauge on filter. Valve secured with rotation [rotate clockwise]; pump activated for leak testing.

Disclaimer

PLEASE READ THE FOLLOWING CAREFULLY

The manufacturer and/or distributor have provided the parts list and assembly diagram in this manual for reference purposes only. They do not make any representation or warranty to the buyer that they are qualified to make repairs to the product or replace any parts of the product. In fact, the manufacturer and/or distributor expressly state that all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer.

The buyer assumes all risk and liability arising from their repairs to the original product or replacement parts or arising from their installation of replacement parts. It is strongly advised that qualified professionals handle any repairs or replacements to ensure safety and proper functioning of the product. Improper installation and operation may result in injury, property damage, or voiding of warranty. The manufacturer and/or distributor shall not be held responsible for any accidents, damages, or malfunctions resulting from the buyer's installation and operation of the product. It is essential to follow all safety guidelines and recommendations provided in this manual and to seek professional assistance if unsure about the installation or operation procedures.

Customer Service

If you have any questions about ordering pool pumps and replacement parts or pool products, please feel free to contact XtremepowerUS using the following contact information:

Customer Service and Technical Support

Phone: (909) 628-0880

Email: customer@xtremepowerusa.com

Hours of Operation: Monday – Friday, 9AM – 4PM (CST)