Instruction Manual

Contact Information

Email: eva@monightsllc.com

Phone:(978)248-8126

Attention

This appliance is not intended for use by persons (including Children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

The document outlines the following sections:

Safety Precaution
Fan Structure Drawing
Installation of Hanging Bracket
Installation of Downrod / Hanger Ball
Hanging of Ceiling Fan
Installation of Fan Blades
Wiring of Ceiling Fan
Installation of Canopy
Installation of Lightkits
Maintenance Tips
Troubleshooting

Troubleshooting

Please check the following before lodging a service report:

PROBLEM	REASON	SOLUTION
Fan not moving	1) Main cables not connected. 2) Check the line wires.	1) Check mains & sub circuit breakers or fuse. 2) Check the line wires connections to the fan & switch housing.
Fan noisy	1) Housing screw loose. 2) Wire nut connections rattles against each other. 3) Canopy touches the ceiling.	1) Tighten all screws. 2) Separate & store neatly all the wire nut connections. 3) Check & ensure the canopy is not touching or too close to the ceiling.
Remote control not working	1) Remote & receiver code different. 2) Battery not installed. 3) Weak Battery.	1) Check that the codes are exactly the same. 2) Install the remote control battery. 3) Change a new battery.

Safety Precaution

IMPORTANT: PLEASE READ BEFORE INSTALLATION

The installation work must be carried out by a qualified wiring installer.
Turn off the Electrical Main Switch at the circuit breaker fuse box.
Using power supply 120V~ / 60Hz.
WARNING: To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box Marked "Acceptable for Fan Support of 15.9 kg (35 lbs) or less" And Use Mounting Screws Provided With The Outlet Box. Most Outlet Boxes Commonly Used For The Support of Luminaires Are Not Acceptable For Fan Support And May Need To Be Replaced. Consult A Qualified Electrician If In Doubt.
CAUTION: To Reduce The Risk Of Injury To Persons, Install Fan So That The Blade Is At Least 3.05 Meters (10 Feet) Above The Floor.
Do not operate the reverse switch when the fan is still in motion mode. Wait till it stop completely before switching to reverse mode.
Do not insert any objects in the path of the blades.
When all electrical connection are done, store all wires neatly.
Make sure all screws and connections are tightly screwed and secured.
The supply wires live and neutral must be connected to a double pole switch having a contact of at least 3mm in all poles.
WARNING: To Reduce The Risk Of Personal Injury, Do Not Bend The Blade Brackets When Installing The Brackets, Balancing The Blades, Or Cleaning The Fan. Do Not Insert Foreign Objects In Between Rotating Fan Blades.
WARNING - To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With An Isolating Wall Control/Switch.
CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan Before Installing Light Kit.

French Warning: ATTENTION: pour réduire le risque de blessures corporelles, installez le ventilateur de manière à ce que la lame se trouve à au moins 3,05 mètres (10 pieds) au-dessus du sol. AVERTISSEMENT: pour réduire le risque d'incendie, de choc électrique ou de blessure, montez sur la boîte de sortie marquée "Acceptable pour un support de ventilateur de 15,9 kg (35 lb) ou moins " et utilisez les vis de montage fournies avec la boîte de sortie. La plupart des boîtiers de sortie couramment utilisés pour le support des luminaires ne sont pas acceptables pour le support des ventilateurs et peuvent devoir être remplacés. Consultez un électricien qualifié en cas de doute.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT DEND THE BLADES BRACKETS DURING ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT ANY OBJECTS IN THE PATH OF THE BLADES.

TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH AN ISOLATION WALL CONTROL / SWITCH.

Maintenance Tips

Because of the fan's natural movement, some connections may be loose. To check the support connections, brackets and blades attachment 2 times a year. Make sure they are all secured (It is not necessary to dismantle the entire fan from ceiling).
Clean your fan periodically to help maintain its appearance over the years. Do not use water when cleaning, use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is coated with a lacquer to minimize the ratio of discoloration or tarnishing which would damage the motor or the wood or possibly cause an electric shock.
You can apply a light coat of furniture varnishing to the wood for additional protection and enhance its beauty. Surface scratched mark can be touch-up with a light coat of shoe polish.
There is no need to oil your fan. The motor is created with lubricated sealed ball bearings.
User are advised to contact the fan supplier to conduct regular examination of the fan suspension system at least once in every two years.

WARNING

MAKE SURE THE POWER IS SWITCH OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT TO ANY REPAIRS (REFER TO THIS SECTION), MAKING ELECTRICAL CONNECTIONS.

French Warning: ASSUREZ-VOUS QUE L'ALIMENTATION EST COUPÉE AU NIVEAU DU BOÎTIER ÉLECTRIQUE AVANT DE TENTER DES RÉPARATIONS (VOIR CETTE SECTION), EN FAISANT DES CONNEXIONS ÉLECTRIQUES.

Fan Structure Drawing

The fan structure comprises the following main components:

Hanger Bracket
Remote control receiver
Downrod
Canopy
Canopy Cover
Decorative Cover
R pin
Cross pin
Motor Housing
Blades
Light Fixture
Acrylic cover
Screws

Associated hardware includes balance washers, wood screws, and expansion screws.

Installation of Canopy

After completing the wiring, attach the canopy to the hanger bracket by pushing it up and twisting to align the screws with the keyholes. Tighten the two screws firmly. Finally, attach the canopy cover with its magnet to the canopy.

Installation of Lightkits

Install the LED lamp.
Remove one screw from the light fixture and loosen the other screws by 3-4mm.
Connect the lightkit wires: white wire to white, and blue wire to blue.
Align the holes of the lightkits with the screws, push up, and twist clockwise.
Fasten the first screw back into its hole and tighten all screws firmly.
Carefully lift the acrylic cover by pushing it up to the light fixture and twist clockwise until it is held tightly in place by the three tabs.

Tools That May Be Used During Installation

Ladder
Screwdriver
Wire Strippers
17/14 spanner
Drill

Wiring of Ceiling Fan

The motor assembly provides three groups of wires:

White and blue wires with a small connector for the lightkit.
Black (L1), Red (L2), and Brown (L3) wires with a big connector for the live wire for the fan.
Green/Yellow wire for ground.

Connect the motor wires to the remote control receiver: the big connector to the big socket and the small connector to the small socket. (Note: Do not connect the small connector for the fan if it does not have a lightkit).

Connect the motor, hanger bracket, hanger ball, and remote control receiver wires to the AC wires: White wire to Neutral, Black wire to Live, and Green/Yellow wire to Ground. Ensure the earth wire is longer than the safety cord by 60mm. This ensures that if the suspension system fails, the current-carrying conductor becomes taut before the earthling conductor, keeping the fan assembly effectively earthed.

Installation of Hanging Bracket

For Wooden Ceiling: Use four wood tooth screws to install the hanger bracket firmly.

For Concrete Ceiling: Use two expansion screws to install the hanger bracket firmly.

Installation of Downrod / Hanger Ball

Remove the screw and pin from the hanger ball. Remove the "R" pin and cross pin from the downrod.
Select a suitable downrod. Place the canopy and decorative cover onto the downrod, then thread the wire through the downrod.
Reinstall the screws and pin to the hanger ball, ensuring the screws are fastened securely.
Loosen the two setscrews in the downrod support (Note: The two setscrews above secure the downrod; the two screws below secure the central spindle and should not be loosened). Insert the downrod into the connector. Install the cross pin and secure it with the "R" pin. (Note: The wire may slightly block the cross pin). Fasten the two setscrews back. The "R" pin must be properly installed to prevent the cross pin from working loose.

Hanging of Ceiling Fan

Carefully lift the fan assembly and attach it to the hanger bracket that is connected to the outlet box. Ensure the rod ball's groove is aligned with the tab on the hanger bracket.

Installation of Fan Blades

Remove the screws on the blade bracket.
Place the blade onto the bracket and install the blade using the screws.