TP-LINK Gigabit Ethernet Media Converter User Guide

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. TP-LINK^® is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.

Visit: http://www.tp-link.com

Package Contents

Before starting using the products, ensure you have received all items. The Converter includes:

• One Converter
• One AC-DC Power Adapter (DC9V/600mA)
• One User Guide

1. Introduction

MC200CM, MC210CS, and MC220L are Gigabit Ethernet Media Converters. The FX port of MC220L supports hot-swappable functionality.

The converter mediates between a 1000Base-TX segment and a 1000Base-X segment. It is primarily designed for larger bandwidth and higher speed demanding workgroups that require expansion of the Gigabit Ethernet network.

MC200CM & MC210CS:

• Rear Panel: Depicts ports labeled 'Power', 'FX', and 'TP', with connections from below.
• Front Panel: Depicts ports labeled 'RJ45' and 'SC', with connections from below.

MC220L:

• Rear Panel: Depicts ports labeled 'TX', 'RX', 'FX', and 'TP', with connections from below.
• Front Panel: Depicts ports labeled 'RJ45' and 'LC', with connections from below.

Note: This media converter can also be powered by a 5VDC Adapter.

2. Features

• Comply with IEEE 802.3ab and IEEE 802.3z standards.
• Provide one SC/LC fiber connector and one RJ45 connector. (Refer to specifications table for model-specific connectors).
• Operate at 1000Mbps in Full-Duplex mode for both TX and FX ports.
• Support auto MDI/MDIX for the TX port.
• Extend fiber distance up to 0.55km for multi-mode fiber and 15km for single-mode fiber. (Refer to specifications table for model-specific distances).
• Features easy-to-view LED indicators for monitoring network activity.
• Requires an external power supply.
• FX port supports hot-swappable functionality (MC220L only).

Connectors and Network Cables Supported

The supported connectors and network cables are:

• Connectors: RJ-45, SC, LC.
• Network Cables: Cat.5 Twisted-Pair (TP), 9/125um Single-mode fiber, 62.5/125 & 50/125um Multi-mode fiber.

Visual depiction of connectors: An image shows an SC fiber connector and an LC fiber connector.

3. Appearance Indication

3.1 LED Indicators

This converter features LED indicators to provide real-time status updates on network activity.

The indicators are:

• PWR: Power status (On: Power on, Off: Power off).
• FX LINK: FX Port link status (On: Valid link, Off: No valid link).
• TP LINK: TP Port link status (On: Valid link, Off: No valid link).
• TP RX: TP Port data reception (On: Receiving data, Off: Not receiving data).

Note: The 'TP' port mentioned in this guide refers to the TX port.

3.2 Switch

The switch controls the FX port mode:

• FORCE: The FX port operates in FORCE mode.
• AUTO: The FX port operates in Auto-Negotiation mode.

Note: Ensure the opposite end uses the same setting. When using two converters together, set both to FORCE mode. When connecting to other products (e.g., TL-SL2210WEB, TL-SL2428WEB), set to Auto-Negotiation mode. It is recommended to leave switches on AUTO. Reset the converter after changing switch settings for the changes to take effect.

4. Installation Guides

4.1 Gigabit Ethernet Media Converter

• The SC fiber connector of MC200CM transmits/receives data using 850nm short wave laser on multi-mode fiber.
• The SC fiber connector of MC210CS transmits/receives data using 1310nm short wave laser on single-mode fiber.

Diagram: Illustrates transmission and reception of data on different fiber types.

Note: Two MC200CM or two MC210CS units can cooperate. MC220L can be used with two kinds of SFP modules: single-mode or multi-mode.

Diagram: Shows an SFP module being plugged into an MC220L.

Diagram: Illustrates data transmission between two MC220L units.

Note: Two MC220L units with the same SFP module can cooperate.

Diagram: Illustrates data transmission between MC220L and MC200CM/MC210CS.

Note: When connecting MC220L to MC200CM or MC210CS, the SFP module in MC220L must match the mode and wavelength of the opposite end. The connection fiber must be LC-SC fiber.

4.2 Configuration

To effectively expand a Gigabit Ethernet network, consider these examples:

1. Place two converters back-to-back between end devices.

Note: For correct connections between two Media Converters (e.g., two MC200CM, two MC210CS, two MC220L, or one MC220L with another MC200CM/MC210CS), refer to the connection diagrams in section 4.1.

2. Connect a converter directly between a 1000Base-TX network and a fiber optic (FX) device.

4.3 Installation Procedure

Use a fiber cable to connect two converters, or connect a converter with a 1000Base-FX Device.

1. Connection of a Converter and a 1000Base-TX Device (HUB or Switch): Ensure the Cat.5 twisted pair cable (Category-5) between the 1000Base-TX device and the converter is less than 100 meters. Connect one end of the Cat.5 cable to the converter's RJ45 jack and the other end to the 1000Base-TX device's RJ45 jack.
2. Connection of two Converters or a Converter and a 1000Base-FX Device: Use a SC fiber cable to connect the SC connectors of the two converters or the SC connector of a converter and a 1000Base-FX Device.
3. Turn on the power.

4.4 Install Media Converter into MC1400

Remove the two screws on either side of the Chassis to install the retainer as follows:

1. Turn off the switch power, remove the front guard on the chassis. Insert the Media Converter into the chassis slot and use the locking knob to secure it tightly.
2. Turn on the switch power. The Media Converter's POWER LED should illuminate. The unit can now operate as a boxlike Media Converter of the MC series.

5. Troubleshooting

If you encounter issues during installation or use, follow these steps. If problems persist, contact your dealer or TP-LINK technical support.

1. PWR LED is off: Indicates a power error. Check that the power lead is connected correctly.
2. LINK LED (TP port) is off: Confirm there is no open circuit with the cable and ensure the device connection type is 1000M.
3. LINK LED (FX port) is off:
   • Check that the fiber mode and fiber type match the Gigabit transceivers.
   • Verify there is no open circuit.
   • Check fiber loss using a Fiber-Optic Tester to avoid excessive signal degradation.
   • Ensure the FX port is connected correctly: The transmitting port (TX) of the local end should connect to the receiving port (RX) of the outlying end, and the receiving port (RX) of the local end should connect to the transmitting port (TX) of the outlying end.

6. Appendix: Specifications

MC200CM

MC210CS

MC220L