Aiper Scuba E1 Robotic Pool Cleaner User Manual

Important Safety Precautions

Read this manual and use the device in accordance with its instructions. Aiper is not responsible for any loss or injury caused by improper use of this device.

1. Do not use the device when people or animals are in the pool.
2. Turn off the cleaner when not in use or when performing maintenance.
3. Never allow children to ride on the device. Supervise children if they are near the operating device.
4. Use only authorized Aiper power adapters.
5. The replacement of the adapter cord should only be performed by a qualified electrician or Aiper customer service.
6. It is recommended to plug the power adapter into a power strip or surge protector, not directly into the electrical outlet.
7. Before charging, ensure the device is turned off and the charging port is dry. The device should be stored in a cool place while charging. Do not cover the device during charging, as this may cause overheating.
8. When the device is not in use, store it indoors or in a cool place.
9. Do not drain the device from the water, as this may cause overheating.
10. The sealed power pack of the device may only be disassembled by certified professionals.
11. Do not use the device and pool filtration simultaneously.
12. The oil seal around the motor contains grease, which may cause minor water contamination if the motor is damaged. If you suspect a leak, stop using the device immediately.
13. Do not puncture the device casing, throw it, or intentionally damage it.
14. When placing the device into the water, the front of the device must face upwards, and it should never be placed upside down or thrown directly into the pool.

1. Structure

The Aiper Scuba E1 consists of the following parts:

• Top Shell
• Ultra-fine Filter
• Filter Basket
• Handle
• Power Button
• Bottom Roller Brush
• Bottom Wheel
• Retractable Hook
• Charger

2. Specifications and Operating Conditions

CAUTION: Do not use the device in pool environments outside the described conditions, as this may cause damage to the device, which is not covered by the warranty.

• Temperature: pH Value: 7.0-7.4
• Chlorine: Maximum 4 ppm
• NaCl: Maximum 5000 ppm

3. Charging

NOTICE: Do not charge the device in direct sunlight.

1. Fully charge the device before using it to clean the pool.
2. Before charging, remove the charging port cover and check for any water residue. If present, dry the charging port first.
3. Insert the charging cable into the device's charging port and then into an available electrical outlet. The LED indicator on the device will start to pulse, indicating that the device is charging. The LED indicator will remain lit when fully charged.

Diagram showing charging connection

4. Using the Aiper Pool Cleaner

This device is designed for cleaning pools with flat floors and no slopes, up to an area of 1100 m²/100m².

Diagram showing pool size suitability

5. Operating the Device

1. Press and hold the power button for 2 seconds to turn the device on/off.
2. After turning on the device, the water pump will rotate for 1 second every 10 seconds, a total of 3 times, to check if it has been placed in the pool. If the device does not detect water during this process, it will automatically shut off. The device will start cleaning shortly after reaching the pool floor.
3. When the battery charge level is low, the device will automatically dock at the pool edge and stop cleaning.
4. Lift the device from the pool floor using the hook to prevent it from getting wet. Users can attach the hook to any standard pool cleaning pole (not included) to extend the hook's reach.
5. Hook the device's handle and lift the device out of the water.
6. Hold the handle and allow the device to drain any accumulated water.

Diagrams illustrating operation steps

6. Disassembly and Cleaning

6.1 Cleaning the Filter Basket

1. Place the device in a safe place and remove the top cover. Ensure the device is stable before removing the top cover. Lift the top shell and open it.
2. Remove the filter basket by lifting its handle.
3. Press the latch of the filter basket's top shell and simultaneously pull the top cover handle upwards to open the filter basket.
4. Empty the filter basket, rinse it, and place it back into the device.

Diagrams illustrating filter basket cleaning

6.2 Cleaning the Ultra-fine Filter

1. Place the device in a safe place and open the top cover.
2. Then, lift the handle of the ultra-fine filter frame and remove the ultra-fine filter assembly from the machine.
3. Remove the ultra-fine filter from the frame.
4. Place the ultra-fine filter on the ground and rinse the front and then the back thoroughly with a high-pressure water gun. Ensure all folds and crevices are completely cleaned. After cleaning, let it dry in a cool, ventilated place to prevent mold and prepare it for future use.

Diagrams illustrating ultra-fine filter cleaning

Notes on Filter Cleaning:

• Rinse the ultra-fine filter after each use to prevent dirt buildup and clogging.
• The ultra-fine filter can capture dust particles as small as 3 µm. Use it when there are few visible impurities in the water (e.g., stones, leaves, sand, debris, and hair), but the water appears cloudy. Do not use it if there are many such impurities.
• Remove the machine from the water after cleaning. Then, rinse the ultra-fine filter immediately to prevent long-term accumulation of dirt, which makes cleaning difficult.
• Neutral cleaning agents can be used for cleaning, but do not scrub the ultra-fine filter with a brush.
• Ultra-fine filter replacement plan: To ensure effective filtration, it should be replaced every 4-6 weeks.

7. Maintenance

7.1 Cleaning/Replacing the Bottom Roller Brush

1. Place the device securely so that its bottom side faces upwards.
2. Hold the roller brush with one hand and support the machine with the other. Gently push the roller brush as indicated by the arrow in the image below, then lift and remove it.
3. After removing the roller brush, clean any entangled debris and any residue left in the machine's brush compartment.
4. After cleaning, reattach the roller brush. Check its secure fit by holding it in the middle and pulling outwards. If installed correctly, it should not detach.

Diagrams illustrating roller brush maintenance

7.2 Cleaning/Replacing the Bottom Wheels

If the machine frequently changes direction unexpectedly, it may be due to the bottom wheels being jammed. Clean them as follows:

1. Place the device securely so that its bottom side faces upwards.
2. Unscrew the bottom wheels.
3. Rinse any dirt, sand, or debris from the inner crevices of the wheels. Be careful not to lose any internal components, such as springs.
4. Reattach the wheels to the machine and ensure the screws are securely fastened.

Diagrams illustrating wheel maintenance

7.3 Cleaning the Outlet

1. Remove the screws and the outlet cover.
2. Remove any objects entangled in the outlet fan blades, then reinstall the outlet cover and screws.

Diagrams illustrating outlet cleaning

8. LED Indicator

Description of LED Colors:

• Full Blue Light: 100%
• Blue: > 50%
• Yellow: 50-15%
• Red: < 15%

9. Packing List

10. Warranty

This product has passed all quality and safety control tests conducted by the factory's technical department.

1. This product is covered by a warranty for the battery and motor from the date of purchase. Warranty conditions are subject to the legal regulations of the respective country.
2. This warranty is void if the product has been modified, misused, or repaired by an unauthorized person.
3. The warranty covers manufacturing defects only and does not cover damage caused by improper handling by the owner.
4. For warranty claims or repairs, the order number or record must be presented.
5. This is an additional warranty offered by AIPER INTELLIGENT SARL, located at 43-47 avenue de la Grande Armée, 75116 Paris, France. This warranty does not affect the consumer's free remedies for non-conformity under the law against the seller.

Warranty Email: service@aiper.com