Trotec PTNS 10-20V Cordless Tacker

Introduction

The Trotec PTNS 10-20V is a high-performance portable cordless tacker designed for the hobby and DIY sector. It is suitable for tacking cardboard, leather, textile or natural fibres, foils, and similar materials onto soft ground such as softwood or material similar to wood.

The device features a magazine filling level indicator, an integrated LED work light, and a battery level indication on the battery itself.

Safety Information

General Power Tool Safety Warnings:

• Work Area Safety: Keep the work area clean and well lit. Do not operate in explosive atmospheres. Keep children and bystanders away.
• Electrical Safety: Ensure proper plugs and outlets. Avoid contact with earthed surfaces. Do not expose to rain or wet conditions. Do not abuse the cord. Use outdoor extension cords and RCDs in damp locations.
• Personal Safety: Stay alert, use common sense, and wear appropriate Personal Protective Equipment (PPE). Always wear eye protection ?. Prevent unintentional starting by ensuring the switch is off before connecting power or battery. Remove any adjusting keys. Do not overreach; maintain proper footing and balance. Dress properly, avoiding loose clothing or jewellery. Use dust extraction facilities if provided. Avoid complacency.
• Power Tool Use and Care: Do not force the tool. Use the correct tool for the application. Repair tools with faulty switches. Disconnect power/battery before adjustments or storage. Store idle tools out of reach of children and untrained users. Maintain tools and accessories; keep cutting tools sharp and clean. Use the tool and accessories as instructed. Keep handles dry and clean.
• Battery Tool Use and Care: Recharge only with the specified charger. Use only specifically designed battery packs. Keep batteries away from metal objects. Avoid contact with battery liquid; flush with water if contact occurs. Do not use damaged or modified batteries. Do not expose batteries to fire or excessive temperatures. Charge within specified temperature ranges.
• Charger Use and Care: Children should only use the charger under supervision. Never insert non-rechargeable batteries. Only charge the specified Li-Ion battery with the specified charger.
• Service: Have the power tool serviced by a qualified repair person using identical replacement parts. Never service damaged battery packs; only the manufacturer or authorized providers should do this.
• Safety Instructions for Tackers: Always assume the tool contains fasteners. Do not point the tool at yourself or others. Push the tool firmly against the workpiece before actuating. Disconnect power/battery when a staple or wire nail is jammed. Exercise caution when removing jams. Do not use for fastening electrical lines. Use pipe detectors for concealed lines. Do not use if the charger plug or cable is damaged.

Personal Protective Equipment (PPE):

• Wear hearing protection ?.
• Wear eye protection ?.
• Wear protective gloves ?.

Residual Risks:

• Warning of electrical voltage: Risk of electric shock from insufficient insulation. Check device for damages before use. Do not use if damp or wet.
• Warning of explosive substances: Do not expose battery to temperatures above 45°C. Avoid contact with water or fire. Risk of explosion.

Intended Use and Foreseeable Misuse

Intended Use: Tacking cardboard, leather, textile or natural fibres, foils, and similar materials onto softwood or material similar to wood.

Foreseeable Misuse: Tacking hard materials such as metals, stone, glass, or hard plastics. Any other use than described is considered misuse.

Personnel Qualifications: Users must have read and understood the instructions, especially the safety chapter.

Safety Signs and Labels

Do not remove safety signs from the device. Keep them legible.

Battery Safety Signs: Indicate risk of explosion from fire, excessive temperature, water, direct sunlight, and moisture. Emphasize correct battery disposal ♻️.

Charger Safety Signs: Advise reading the manual and using the charger only in dry, indoor spaces.

Device Depiction and Scope of Delivery

Device Components:

• 1: Battery holder
• 2: Trigger
• 3: Magazine filling level indicator
• 4: Magazine slider
• 5: Tacker guide nose / staple ejection
• 6: LED work lamp
• 7: Quick charger
• 8: Red battery LED (battery charging)
• 9: Battery
• 10: Staples
• 11: Wire nails
• 12: Battery level indication
• 13: Release button
• 14: Green battery LED (quick charger ready)
• 15: Button for LED work lamp
• 16: Impact force regulator

Scope of Delivery:

• 1 x Device PTNS 10-20V
• 1 x Rechargeable battery
• 1 x Quick charger
• 500 x Staples (type 55, 20mm length, 6mm width)
• 500 x Wire nails (type 47, 20mm length, 0.8mm width)
• 1 x Transport case
• 1 x Manual

Technical Data

Noise and Vibration Information: Vibration levels are measured according to EN 60745. Prolonged exposure to vibration can cause health hazards. Vibration levels may vary based on usage.

Transport and Storage

Transport: Use the provided transport case. Before transporting, switch off the device, unplug the charger, allow it to cool, and remove the battery. Observe regulations for transporting Li-ion batteries.

Storage: Store the device in a dry place, protected from frost, heat, dust, and direct sunlight, ideally in the transport case. Ensure ambient temperature is below 45°C. Do not store discharged Li-ion batteries.

Start-up

Unpacking: Remove the device and accessories from packaging. Check for completeness and damages. Dispose of packaging material responsibly.

Charging the Battery:

• Note: Improper charging can damage the battery. Remove charger plug before handling the battery. Charge between 10°C and 40°C.
• The battery is partially charged upon delivery.
• To charge: Slide battery (9) onto the quick charger (7) until it locks. Plug the charger into a socket. The red LED (8) will light up. Charging takes approximately 1 hour. Wait for the red LED to turn off and the green LED (14) to light up, indicating a full charge. Unplug the charger, allow the battery to cool, then remove it by pressing the release button (13).

Inserting the Battery: Slide the battery (9) onto the device until it locks in place.

Checking Battery Status: The battery level indication (12) on the battery shows the charge status via LEDs (Green-Orange-Red for max, Orange-Red for medium, Red for weak charge).

Removing the Battery: Press the unlocking button (13) and pull the battery (9) off the device.

Filling the Magazine:

• Warning: Remove battery before filling. Do not hold the trigger when a staple/nail is jammed. Wear safety glasses ?.
• Use the magazine filling level indicator (3) to check the supply.
• Do not force the magazine open or closed.
• To fill: Remove battery. Turn device upside down. Squeeze magazine release (18) and pull magazine slider (4) back. Insert staples (10) with tips pointing up, or wire nails (11) with heads pointing down (observe mark 20). Slide magazine slider (4) back into place until it clicks.

Operation

Impact Force Preselection: Adjust the impact force using the regulator (16) for different materials (stages 1-6). Start with the lowest setting and test on excess material.

Switching the Device On and Off: Wear PPE. Place the device on the workpiece and push the trigger (2). The trigger is linked to the guide nose (5) and only activates when pressed against the workpiece.

Operation Tips: Apply the device firmly and at a right angle to the workpiece. Be careful on soft workpieces. Observe fastener sizes. Check magazine level indicator.

Shutdown: Switch off the device. Unplug the charger. Remove the battery. Clean and store the device as per instructions.

Available Accessories

Warning: Only use specified accessories. Using other tools may cause injury.

Errors and Faults

First Use: Light smoke or odour is normal and disappears after brief use.

Battery Not Charging: Check battery insertion, power connection, cable/plug, fusing, charger condition, and battery terminals. Batteries may need replacement.

Device Not Starting: Battery may be low. Check battery connection to the device and clean terminals. Ensure the tacker guide nose is properly engaged with the workpiece.

Jammed Staple or Wire Nail: Remove the battery first. Do not hold the trigger. Open magazine release to remove the fastener.

No Staple or Wire Nail Ejection: Check fastener insertion and magazine level. Insert new fasteners if needed.

Staple/Nail Not Penetrating Deeply: Adjust the impact force regulator (16).

Device Becomes Hot: Keep ventilation openings clear. Wait 10 minutes before restarting.

Device Not Operating Correctly: Contact customer service or an authorized specialist company for repair.

Maintenance

Before Maintenance: Switch off the device, allow it to cool, and remove the battery.

Notes: No user-serviceable parts inside. Maintenance requiring housing opening must be done by authorized specialists.

Safety Signs: Check battery and charger safety signs regularly.

Cleaning: Clean the device before and after each use with a soft, damp, lint-free cloth. Avoid aggressive cleaning agents. Keep connecting terminals clean. Keep ventilation openings free of dust.

Disposal

Equipment Disposal: Do not dispose of this electrical equipment with household waste. Use designated collection points. Refer to https://hub.trotec.com/?id=45090 for EU options.

Battery Disposal: Batteries must be disposed of professionally according to EU Directive 2006/66/EC. Do not dispose of in waste water or public waters.

Declaration of Conformity

Trotec GmbH declares that the PTNS 10-20V cordless tacker complies with EC Machinery Directive 2006/42/EC and other relevant EU directives.

Product Model: PTNS 10-20V

Product Type: Cordless tacker

Year of Manufacture: 2021

Manufacturer: Trotec GmbH, Grebbener Straße 7, D-52525 Heinsberg. Contact: +49 2452 962-400, info@trotec.de.

Place and Date of Issue: Heinsberg, 12.08.2021.