Manuals+

Dreo Smart Tower Fan Cruiser TF518S User Manual

Thank you for choosing Dreo!

01 Important Safety Instructions

! READ ALL CAUTIONARY MARKINGS ON THE APPLIANCE AND SAFETY INSTRUCTIONS IN THE USER MANUAL BEFORE USE.

Do not cover the air inlet and outlet while in operation. ?️

Do not use the fan near flammables and combustibles. ?

General Safety

  1. Children shall not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
  2. Use the appliance as described in the user manual only. Any other use not recommended in the user manual may cause fire, electrical shock, or personal injury.
  3. This appliance can be used by children aged above 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this appliance in a safe way and understand the hazards involved.

Operation Safety

  1. Place the appliance on a flat, dry surface before use.
  2. Do not immerse in water and any other liquids. ?
  3. Do not use the appliance until the base is installed.
  4. Do not insert your fingers, pencil, and any other objects into the grilles while in operation.
  5. Do not dismantle, repair, or modify. All servicing should be performed by qualified personnel.

Electricity Safety

  1. Make sure that the voltage of your electricity supply is the same as that indicated on the appliance.
  2. Always unplug before cleaning or leaving the appliance unused for a long period of time. Keep your hands dry when plugging/unplugging. ?
  3. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
  4. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliance. Arrange cord away from traffic area and where it will not be tripped over.
  5. WARNING: To reduce the risk of fire or electric shock, do not use this Fan with any solid-state speed control device.
  6. This appliance employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions and check the appliance. If the replacement fuse blows, a short-circuit may be present and the appliance should be discarded or returned to an authorized service facility for examination and/or repair.
  7. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
  8. WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).

FOR HOUSEHOLD USE ONLY

READ AND SAVE THESE INSTRUCTIONS

Gentle Reminder:

Check the appliance regularly and refer to TROUBLESHOOTING or contact our customer support if it shows any of the following signs:

  • Power cord or plug is damaged.
  • Loud noise, unusual smell or excessive heat.

Specifications

Model No. DR-HTF018S
Input AC 120V 60Hz
Rated Power 35W
Battery Type CR2025 3V

02 Assembling Your Tower Fan

Assembly Instructions

When using the appliance for the first time, remove the wraps and attach the parts by following the steps below.

  1. Illustration showing two base halves intersecting diagonally.
    Intersect the two base halves diagonally.
  2. Illustration showing the arched cutout on the base matching the arched support, and hooks engaging.
    Match the arched cutout with the arched support on the base. Then, hook them together.
  3. Illustration showing arrows pointing down on the edges of the base halves, with 'Press' indicated.
    Press down on the edge until you hear a click to securely snap the two base halves together.
  4. Illustration showing the power cord being threaded through the center hole and attached to the fan bottom.
    Thread the cord through the center hole and attach the base to the fan bottom.
  5. Illustration showing arrows indicating alignment of the base and fan bottom.
    Make sure the arrows on both the base and fan bottom are aligned.
  6. Illustration showing the base being turned clockwise until it clicks into place.
    Turn the base clockwise until it clicks into place. ⚙️
  7. Illustration showing the power cord threaded through rear cord keepers and the fan set upright.
    Thread the cord through all REAR cord keepers, then set the fan upright.

CAUTION

  • Do not operate the tower fan if the base has not been installed.
  • Make sure to thread the cord through all rear cord keepers.

03 Connecting to Your Tower Fan

Before connecting the appliance to your mobile device, please scan the QR code on the left or go to the app store and search "DREO", then select and download the app.

Download on the App Store GET IT ON Google Play

Look for "Cruiser TF518S" when connecting your new tower fan.

? You can use the DREO app to connect your smart tower fan to Amazon Alexa or Google Home. Please follow the in-app instructions to set up your voice assistant.

NOTE: You must create a DREO account to access voice assistants.

  1. Launch DREO and sign in or create account by following in-app instructions.
  2. Enable Bluetooth on your mobile device and plug in your tower fan.
  3. Hold the Oscillation button ? for 5 seconds to start WiFi connection settings. (Tip: The WiFi icon ? will keep flashing when pairing.)
  4. Tap + Add Device and select Cruiser TF518S.
  5. Follow in-app instructions to complete WiFi connection.
  6. You're now ready to control the appliance on your app. (Tip: To restart connection settings, hold the Oscillation button ? again for 5 seconds.)

Long press 10 seconds power button ⏻ to unpair WiFi and restore factory settings.

04 Knowing Your Tower Fan

Control Panel

LED Display

Normal Mode

Natural Mode

Sleep Mode

Auto Mode

WiFi ?
Mute ?
Fan Speed ?
Timer ?
88
⏻ ? - + ≡ ?

05 Using Your Tower Fan

Working Modes

Additional Features

Timer

? When the fan is ON/OFF, touch the timer button repeatedly to set a timer (1-12 h). When the timer ends, the fan will stop/start running automatically. To cancel, set the time to 0 hour.

Note: Display will return to fan speed after 3 seconds.

Memory

? If the fan is turned OFF or disconnected from power, it will operate under the previous settings (except the timer setting) when it is turned ON again.

Display Auto Off

AUTO • Display turns off after 1 minute (after 5 seconds in sleep mode). • Wake up the display with any button. • To disable this feature, please go to the DREO app.

Getting the Most out of Your Tower Fan

  1. Remove any tall obstacles that might block the airflow from the fan.
  2. Combine with your AC unit to get cooler air throughout the room.
  3. Position the tower fan closer to you to get more direct airflow.
  4. Place a bucket of ice in front of the fan for an extra cooling boost. ?
Diagram of the Dreo Smart Tower Fan.