ZKTeco | Biometrics and Computer Vision
Installation Guide for ZKTECO models including: E2 Series, E2 Series Horus Access control terminal, E2 Series, Horus Access control terminal, Access control terminal, control terminal, terminal
File Info : application/pdf, 7 Pages, 90.40MB
DocumentDocumentInstallation Guide Horus E2 Series Version: 1.0 Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual. About the Device Installation Please refer to the following recommendations for installation. Installation Environment INSTALL INDOORS ONLY AVOID INSTALLATION NEAR GLASS WINDOWS AVOID DIRECT SUNLIGHT AND EXPOSURE AVOID USE OF ANY HEAT SOURCE NEAR THE DEVICE Install on the wall Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. Fix the backplate on the wall with the wall mounting screws. After passing the wires through the wiring hole and connecting them to the device, and then snap the device onto the backplate and push it down into place. Fasten the device to the backplate with two security screws. 1 Baseline 2 1.55m 3 4 1 2 1 Terminal Block Power In Power Out Wiegand In Wiegand Out RS485 12VIN GND 12VOUT GND IWD0 IWD1 WD0 WD1 GND 485A 485B RXRX+ TXTX+ AL+ ALNC1 COM1 NO1 BUT SEN GND AUX Network Interface Alarm Lock Exit Button Door Sensor Auxiliary Input Ethernet Connection Establish the connection between the device and the software using an Ethernet cable. An illustrative example is provided below: PC Default IP address: 192.168.1.201 Subnet mask: 255.255.255.0 IP address: 192.168.1.130 Subnet mask: 255.255.255.0 Tap on to enter the main menu. And then click on [Comm.] > [Ethernet] > [IP Address] to input the IP address. Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment when connecting to the software. 2 Power Connection AC Adapter DC12V, 3A Recommended AC adapter: 12V, 3A To share power with other devices, use an AC adapter with highercurrent ratings. Exit Button, Door Sensor & Auxiliary Connection AL+ ALNC1 COM1 NO1 BUT SEN GND AUX Exit button Door Sensor COM NO +12V DC Smoke Detector 3 Alarm & RS485 Reader Connection AL+ ALNC1 COM1 NO1 BUT SEN GND AUX WD0 WD1 GND 485A 485B GND +12V DC Alarm +12V GND 485485+ RS485 Reader Wiegand Reader & Access Control Connection 12VOUT GND IWD0 IWD1 WD0 WD1 GND 485A 485B 4 VCC GND WD0 WD1 Wiegand Reader WD0 WD1 GND +12V GND Access Controller Lock Relay Connection The system supports both Normally Opened Lock and Normally Closed Lock. The NO LOCK (normally opened at power on) is connected with 'NO' and 'COM' terminals, and the NC LOCK (normally closed at power on) is connected with 'NC' and 'COM' terminals. Take NC Lock as an example below: 1) Device not sharing power with the lock2)Devicesha ring power with the lock +12V DC FR107 Normally Closed Lock +12V DC 12VIN GND AL+ ALNC1 COM1 NO1 BUT SEN GND AUX +12V DC FR107 Normally Closed Lock 12VIN GND AL+ ALNC1 COM1 NO1 BUT SEN GND AUX Download Center Scan the QR Code to download the User Manual, Installation Guide and Quick Start Guide. 5 ZKTeco Industrial Park, No. 32, Industrial Road, Tangxia Town, Dongguan, China. Phone : +86 769 - 82109991 Fax : +86 755 - 89602394 www.zkteco.com