Table of Contents
- 1. Overview
- 2. What's New in This Release
- 3. Supported Platforms
- 4. Supported Utilities
- 5. Files lists contains in the Release ZIP file
- 6. Read Me First before Upgrade
- 7. Enhancements
- 8. Resolved Issues
- 9. Design Limitations and Known Issues
- Appendix - A. System Default Setting
1. Overview
This document provides release notes for Zyxel Firmware version V5.10.
2. What's New in This Release
3. Supported Platforms
- NWA5121-NI: V5.10(AAID.8)
- NWA5123-NI: V5.10(AAHY.8)
- NWA5121-N: V5.10(AAIF.8)
- NWA5301-NJ: V5.10(AANB.8)
4. Supported Utilities
Zyxel One Network (ZON):
| Series | Access Point | Wireless LAN Controller |
|---|---|---|
| Model | NWA3160-N | NXC2500 |
| NWA3560-N | NXC5500 | |
| NWA3550-N | ||
| NWA5160N | ||
| NWA5560-N | ||
| NWA5550-N | ||
| NWA5123-AC | ||
| NWA5121-NI | ||
| NWA5121-N | ||
| NWA5123-NI | ||
| NWA5123-AC HD | ||
| NWA5301-NJ | ||
| WAC5302D-S | ||
| WAC6103D-I | ||
| WAC6502D-E | ||
| WAC6502D-S | ||
| WAC6503D-S | ||
| WAC6552D-S | ||
| WAC6553D-E | ||
| WAC6303D-S | ||
| WAX650S | ||
| WAX510D | ||
| NWA110AX |
Zyxel AP Configurator (ZAC):
| Series | Access Point |
|---|---|
| Model | NWA5121-NI |
| NWA5121-N | |
| NWA5123-NI | |
| NWA5123-AC | |
| NWA5123-AC HD | |
| NWA5301-NJ | |
| WAC5302D-S | |
| WAC6103D-I | |
| WAC6502D-E | |
| WAC6502D-S | |
| WAC6503D-S | |
| WAC6552D-S | |
| WAC6553D-E | |
| WAC6303D-S | |
| WAX650S | |
| WAX510D |
* ZAC configuration of Access Point is supported with Standalone AP mode.
Zyxel Wireless Optimizer (ZWO)
| Series | Access Point | Wireless LAN Controller |
|---|---|---|
| Model | NWA3160-N | NXC2500 |
| NWA3560-N | NXC5500 | |
| NWA3550-N | ||
| NWA5160N | ||
| NWA5560-N | ||
| NWA5550-N | ||
| NWA5123-AC | ||
| NWA5121-NI | ||
| NWA5121-N | ||
| NWA5123-NI | ||
| NWA5123-AC HD | ||
| NWA5301-NJ | ||
| WAC5302D-S | ||
| WAC6103D-I | ||
| WAC6502D-E |
5. Files lists contains in the Release ZIP file
- File name: *.bin
Purpose: This binary firmware image file is for normal system update. Note: The firmware update may take five or more minutes depending on the scale of device configuration. The more complex configuration will take more update time. Do not turn off or reset the device while the firmware update is in progress. The firmware might get damaged, if device loss power or you reset the device during the firmware upload. You might need to refer to Appendix 2 of this document to recover the firmware. - File name: *.conf
Purpose: This ASCII file contains default system configuration commands. - File name: *-MIB.zip
Purpose: The MIBs are to collect information on device. The focus of the MIBs is to let administrators collect statistical data and monitor status and performance.
6. Read Me First before Upgrade
This section encompasses important notes while upgrading this firmware release for Zyxel NXC controllers and Zyxel Access Points.
7. Enhancements
8. Resolved Issues
- [181201162] Captive portal redirect on AP will always match to the first one rule.
- [181200940] CPU usage will reach 100%.
- [181200940] AP will reboot automatically due to some reasons.
- [191001364] Admin credential on the AP will not be changed after managed by USG.
- [191000269] AP may reboot unexpectedly with IGMP application.
- [181200956] The AP management VLAN tag will be disappeared after managed by NXC.
- [191200352] AP sends wrong accounting report value.
9. Design Limitations and Known Issues
This section describes the system behavior or limitations in this firmware release. They will be created into knowledge base.
Design Limitations
Known Issues
Appendix - A. System Default Setting
Zyxel NXC WLAN Controller
Following is the system default configuration:
- The default device information for NXC controllers:
IP: 192.168.1.1
Administration username: admin
Password: 1234 - The default LAN interface is vlano. The default LAN subnet is 192.168.1.0/24.
- By default, SSH service can only be accessed from LAN subnet.
Zyxel Access Points in Standalone Mode
- For AP in Standalone mode, following is the system default configuration:
The default device information for Unified Access Points
IP: 192.168.1.2
Administration username: admin
Password: 1234 - For AP in Managed AP mode by default, DHCP client enabled is by default.
