Dreame AirStyle Pro User Manual

Safety Instructions

Carefully read all instructions before using the multi-styler. Always follow basic safety precautions, including those listed below.

The multi-styler contains magnets. Keep it away from implanted medical devices (e.g., pacemakers and defibrillators) as strong magnetic fields can negatively affect them. Additionally, credit cards and electronic storage media may become unusable.

Warnings

The following warnings apply to the multi-styler and all necessary accessories. To reduce the risk of fire, electric shock, and injury, ensure compliance with the following requirements:

• The multi-styler is not intended for use by persons with physical, sensory, or mental impairments, or persons lacking experience and knowledge (including children), unless they are supervised or instructed by a guardian who has ensured they can safely use the product.
• Do not use the multi-styler as a toy. Use by children or near children requires special caution. Supervise children and ensure they do not use the multi-styler as a toy.
• If the multi-styler is used in a bathroom, unplug it after use. Water presence can be dangerous even after the multi-styler is turned off.
• The symbols below indicate the following warning: Do not use the multi-styler near a bathtub, shower, sink, or other water-filled containers. ?
• If the power cord is damaged, it must be replaced or repaired by the manufacturer's service center, a service representative, or a qualified technician.
• The multi-styler is equipped with a self-resetting thermal cut-off device to prevent overheating. In case of power interruption, unplug the multi-styler and let it cool down.
• Caution! To avoid problems caused by accidental activation of the thermal protection, the multi-styler should not be connected to an external switching device (e.g., a timer) or an electrical circuit that regularly switches on and off household appliances.
• For additional protection, it is recommended to install a residual current device (RCD) with a rated operating current not exceeding 30 mA in the electrical circuit supplying the bathroom. Consult a specialist for the installation of protective devices.
• The multi-styler should be used exclusively for hair styling.
• Do not touch the multi-styler plug or any part of it with wet hands.
• Do not unplug by pulling the power cord, and do not stretch or pull it while using the multi-styler. Do not use extension cords or wrap the power cord around the multi-styler.
• Do not apply lubricants, cleaning agents, polishes, or air fresheners to any part of this multi-styler.
• If technical service or repair is required, contact customer support. Do not disassemble the multi-styler. Improper disassembly may lead to electric shock or fire.
• If the multi-styler is not working properly, has been subjected to a strong impact, dropped from a height, damaged, placed outdoors, or fallen into water, do not use it and contact customer support.
• This multi-styler can be used without accessories. For best results, it is recommended to use the multi-styler with attachments.
• Rated power is measured during multi-styler operation without accessories.
• Before performing any repair, cleaning, or maintenance, turn off the power or unplug the unit.
• Hold the operating multi-styler by the handle.
• Accessories and ventilation openings heat up during operation. Wait for them to cool down before further use. ⚠️

Additional Information

Care for the Dreame Multi-styler

• Do not perform any maintenance or repair operations other than those specified in this user manual or recommended by Dreame support staff.
• Before checking for malfunctions, always disconnect the multi-styler from the power supply. If the multi-styler is not working, first check the power in the outlet and the correct plug connection.

Getting to Know the Multi-styler

Attachments:

• Fast Dry Nozzle
• For Unruly Hair Nozzle
• Round Brush for Hair Volume
• Smoothing Brush with Soft Bristles
• Smoothing Brush with Hard Bristles
• 32 mm Auto-Curl Tongs (Left)
• 32 mm Auto-Curl Tongs (Right)
• Cleaning Brush
• Storage Case

General Information about the Multi-styler

The symbols on the multi-styler body remind you not to use the multi-styler while bathing or showering. Product images, accessories, user interfaces, etc., in this manual are for illustrative purposes only and are intended for familiarization. Due to product updates and modernization, the actual appearance may vary slightly. Refer to the actual product.

Key Components:

1. Temperature and Airflow Indicator
2. Airflow Speed Adjustment Button
3. Temperature Adjustment Button
4. Cool Shot
5. Power Supply
6. Removable Filter Cover

Switching Function

Power Switch Position

Slide the power switch up or down to quickly turn the multi-styler on or off. To turn on the multi-styler, move the switch up, and to turn it off, move it down.

Before plugging the multi-styler into the electrical outlet, ensure the power switch is in the off position.

On

Off

Cool Shot Mode

After turning on the power, press and hold the switch, then slide it up slightly to quickly switch to cool shot mode for styling. Press the button to exit cool shot mode.

Airflow Speed Setting

Switching between low, medium, and high airflow speeds is done by lightly pressing the airflow speed adjustment button.

• Low Airflow Speed
• Medium Airflow Speed
• High Airflow Speed

Temperature Setting

To switch between cool, warm, and hot airflow, lightly press the temperature adjustment button.

• White: Cool Airflow
• Orange: Warm Airflow
• Red: Hot Airflow

Using the Multi-styler

Attaching the Nozzle

Align the nozzle with the multi-styler to connect them. Then, turn left to secure the nozzle.

1. Align and push.
2. Turn left to lock.

Thermal Safety Tips

The auto-curl tongs, round brush, and unruly hair nozzle heat up during multi-styler use. Touching the surface of the attachments, except for the insulated tip, can cause burns. If you need to change an attachment, wait for the temperature to drop to a safe level before changing it. ?

Be extremely careful when handling hot attachments. Grip the attachments only as shown in the illustration. Some attachments may require periodic cleaning.

Filter Maintenance

Step 1

Turn the filter cover and detach it from the bottom of the handle.

Illustration showing filter removal

Step 2

Use the cleaning brush to gently remove dust from the surface of the filter cover and the filter mesh.

Illustration showing cleaning the filter

Step 3

After cleaning, attach the filter cover to the handle and turn it to secure.

Illustration showing filter reattachment

Basic Parameters

Dreame AirStyle Pro Styler Troubleshooting