Hytronik Motion Sensors: HC038V/BT & HCD038/BT

Product Description

HC038V/BT (0/1-10V Output)

HCD038/BT (DALI Output)

The HC038V/BT is a Bluetooth 0/1-10V control base, while the HCD038/BT is a Bluetooth DALI control base with a built-in 30mA DALI power supply. Both models work with a wide range of microwave and PIR sensor heads. They are ideal for plastic luminaires as Bluetooth signals can transmit through plastic, making them preferable to metal luminaires in some cases. These sensors are suitable for typical indoor applications such as offices, classrooms, car parks, warehouses, and other commercial or industrial areas. With Bluetooth wireless mesh networking, communication is simplified without the need for extensive hardwiring, adding value to luminaires and reducing project costs. Device setup and commissioning can be easily managed via the Koolmesh™ app.

App Features

• Quick setup mode & advanced setup mode
• Web app/platform for project deployment & data analysis
• Koolmesh Pro app on iPad for on-site configuration
• Floorplan feature to simplify project planning
• D4i supported
• One-key device replacement
• Device social relations check
• Staircase function (primary & secondary)
• Remote control via gateway support (HBGW01)
• Heat map functionality
• Dynamic daylight harvest auto-adaptation
• Grouping luminaires via mesh network
• Scene control
• Dusk/Dawn photocell (Twilight function)
• Tri-level control
• Daylight harvest functionality
• Push switch configuration
• Detailed motion sensor settings
• Schedule functionality
• Astro timer (sunrise and sunset)
• Power-on status memory (retains settings against power loss)
• Offline commissioning
• Bulk commissioning (copy and paste settings)
• Different permission levels via authority management
• Network sharing via QR code or keycode
• Interoperability with Hytronik Bluetooth product portfolio

Compatibility & IoT Features

• Compatible with EnOcean BLE switches
• Internet-of-Things (IoT) featured
• Device firmware update over-the-air (OTA)
• Continuous development in progress

Hardware Features

• HC038V/BT: 0/1-10V output: 400VA (capacitive), 800W (resistive)
• HCD038/BT: 30mA DALI broadcast output for up to 15 LED drivers
• Plug'n'Play for flexible installation and cost-saving assembly
• Support to control DT8 LED drivers (HCD038/BT)
• 2 Push inputs for flexible manual control (HCD038/BT)
• Zero crossing detection circuit to reduce in-rush current and prolong relay lifetime (HC038V/BT)
• Loop-in and loop-out terminals for efficient installation (HC038V/BT only)
• 5-year warranty

Technical Specifications

Bluetooth Transceiver

Safety & EMC

Input & Output Characteristics

Environment

Mechanical Structure & Dimensions

Diagrams illustrating the physical dimensions and terminal layouts for the HC038V/BT (0/1-10V output) and HCD038/BT (DALI output) control bases are provided, showing the placement of the Bluetooth module, 0/1-10V terminals, RJ12 connector for DALI, and power terminals (L, N).

Wire preparation details indicate the use of wires with a gauge of 0.75~1.5mm and a stripping length of 8mm. A diagram shows how to release wires from terminals using a screwdriver.

Wiring Diagram

Wiring diagrams are provided for both the HC038V/BT and HCD038/BT models, illustrating connections to LED drivers, power supply (L, N), and push switches (PUSH1, PUSH2).

Sensor Heads

PIR Sensor Properties

Detailed diagrams with dimensions are shown for PIR sensor heads including HIR05, HIR05/FM, HIR05/AA, HIR07, HIR11/S, HIR11/F, HIR11/C, HIR12, HIR63, HIR63 with HA04, HIR63 with HA05, and HIR63/R. These diagrams illustrate features like lens type, cable length (around 30cm), installation holes, and specific application suitability (e.g., highbay, flush mounting, surface mounting).

HF Sensor Properties

A note indicates that detection range is influenced by sensor placement, angle, and walking pace, and may be reduced under certain conditions.

Diagrams with dimensions are provided for HF sensor heads including SAM20, SAM21, SAM22, SAM22/AA, and SAM23, detailing features like photocell advance, infrared remote receiver, slots for tubes, and cable entry points.

Optional Accessory: Reinforced Bluetooth Antenna

Optional reinforced Bluetooth antennas (HA01B, HA01W) are available to enhance transmission range. When used with the control base, the smartphone-to-device distance increases to 20m, and device-to-device distance extends to approximately 50m. Diagrams show installation details for these antennas.

Detection Patterns

Detection pattern diagrams illustrate the coverage areas for various sensor heads at different ceiling heights and movement types (radial, tangential). These patterns are based on a movement speed of 5 km/h.

• SAM23: Shows detection zones (10%, 30%, 50%, 75%) based on ceiling height up to 15m.
• SAM20 & SAM21 & SAM22 & SAM22/AA: Shows detection zones based on ceiling height up to 10m.
• HIRO5 & HIRO5/FM & HIRO5/AA & HIR07: Illustrates detection coverage for radial and tangential movement, with ranges specified (e.g., 3m radial, 4m tangential).
• HIR12: Shows detection ranges at different heights (3m, 5m, 12m, 15m), including specific ranges for forklift use.
• HIR63: Depicts detection range for person and forklift movement.
• HIR63/R: Shows detection range for person and forklift movement, with specified tangential ranges.

HIR11 (High-bay) Detection Patterns

For Forklift

Detection patterns for HIR11 high-bay lens for forklift detection at Ta = 20°C, with recommended installation heights from 10m to 15m. Tables detail tangential and radial coverage areas (in m²) for various mount heights.

For Single Person

Detection patterns for HIR11 high-bay lens for single person detection at Ta = 20°C, with recommended installation heights from 2.5m to 12m. Tables detail tangential and radial coverage areas (in m²) for various mount heights.

Dimming Interface Operation Notes

Switch-Dim

The Switch-Dim interface allows for simple dimming using commercially available non-latching (momentary) wall switches. Detailed push switch configurations can be set via the Koolmesh app.

Additional Information / Documents

• For full explanation of Hytronik Photocell Advance™ technology, please refer to www.hytronik.com/download -> knowledge -> Introduction of Photocell Advance
• To learn more about detailed product features/functions, please refer to www.hytronik.com/download -> knowledge -> Introduction of App Scenes and Product Functions
• Regarding precautions for Bluetooth product installation and operation, please refer to www.hytronik.com/download -> knowledge -> Bluetooth Products - Precautions for Product Installation and Operation
• Regarding precautions for microwave sensor installation and operation, please refer to www.hytronik.com/download -> knowledge -> Microwave Sensors - Precautions for Product Installation and Operation
• Regarding precautions for PIR Sensors installation and operation, please refer to www.hytronik.com/download -> knowledge -> PIR Sensors - Precautions for Product Installation and Operation
• Data sheet is subject to change without notice. Please always refer to the most recent release on www.hytronik.com/products/bluetooth technology -> Bluetooth Sensors
• Regarding Hytronik standard guarantee policy, please refer to www.hytronik.com/download -> knowledge -> Hytronik Standard Guarantee Policy