BISSELL Little Green® Portable Deep Cleaner User's Guide

Introduction

Thank you for purchasing a BISSELL Little Green Portable Deep Cleaner. This guide is designed to help you get the most satisfaction from your cleaner. It contains assembly and operating instructions, safety precautions, maintenance, and troubleshooting information. Please read this guide thoroughly before assembling and using your cleaner.

BISSELL has been designing, manufacturing, and servicing high-quality homecare products since 1876. Your Little Green is well-made and backed by a one-year warranty and a dedicated Consumer Services department.

Important Safety Instructions

WARNING: When using an electrical appliance, basic precautions should be observed, including the following:

• Read all instructions before using your LITTLE GREEN®.
• Use only on surfaces moistened by the cleaning process.
• Always connect to a properly grounded outlet. See grounding instructions.
• Unplug from outlet when not in use and before conducting maintenance or troubleshooting.
• To reduce the risk of fire, electric shock, or injury:
• Do not expose to rain; store indoors.
• Do not leave LITTLE GREEN® plugged in.
• Do not service LITTLE GREEN® when it is plugged in.
• Do not use with a damaged cord or plug.
• Do not use LITTLE GREEN® if it has been dropped, damaged, left outdoors, or dropped into water; have it repaired at an Authorized Service Center.
• Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces.
• Do not carry the appliance while in use.
• Do not handle LITTLE GREEN® plug or appliance with wet hands.
• Do not put any object into appliance openings, use with blocked opening, or restrict air flow.
• Do not expose hair, loose clothing, fingers, or body parts to openings or moving parts.
• Do not pick up hot or burning objects.
• Do not pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapor.
• Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
• Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, gasoline, etc.).
• Do not modify the 3-prong grounded plug.
• Do not allow to be used as a toy.
• Do not use for any purpose other than described in this User's Guide.
• Unplug before attaching the TurboBrush™.
• Never spray at people or animals.
• Use only manufacturer's recommended attachments.
• Use only cleaning products formulated by BISSELL for use in this appliance.
• Keep openings free of dust, lint, hair, etc.
• Keep appliance on a level surface.
• Turn off all controls before unplugging.
• Unplug by grasping the plug, not the cord. Do not unplug by pulling on cord.
• Be extra careful when cleaning stairs.
• Close attention is necessary when used by or near children.

Grounding Instructions

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Diagram showing a standard electrical outlet with three slots, labeled 'Grounded Outlets', and a three-prong plug with a grounding pin, labeled 'Grounding Pin'.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren't sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the drawing above. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

This model is for household use only.

Product View

WARNING: Do not use this product while on any type of a ladder. Do not place the product in a place where it will be stepped on or kicked while in use. Do not place the product on an elevated surface where it may be pulled off the surface while in use.

Illustration of the BISSELL Little Green Portable Deep Cleaner. Key components are labeled: 1. Solution/Clean Tank, 2. Cap, 3. Collection/Dirty Tank, 4. Spray Trigger, 5. 4" Cleaning Tool, 6. Power Cord, 7. Heater. Other visible parts include the Power Switch, Heater Switch, Heat Indicator Light, Vacuum Flex Hose, and On Board Cord Storage.

WARNING: Do not use an extension cord with this product. The use of an extension cord may result in a severe electrical shock, particularly if the extension cord does not have an electrical rating higher than that of the product, if the extension cord does not have a three prong grounding plug and connector and if the extension cord is not plugged into a circuit box with a ground fault circuit interrupter. Safety precautions such as keeping all connections off the ground and dry will not eliminate the danger.

Product Features

This User's Guide has been designed to help you get the utmost satisfaction from your BISSELL Little Green Portable Deep Cleaner. You'll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your cleaner. Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go. Following this User's Guide will greatly enhance your ability to get the most performance from your BISSELL Little Green for many years.

WARNING: Do Not plug in your deep cleaner until you have completely assembled it per the following instructions and are familiar with all instructions and operating procedures.

Solution Tank

The Solution Tank is the translucent tank located on the right side of the unit when facing it. To remove, grasp the indented handle and pull toward you, then tilt out.

To Fill the Solution Tank:

1. Open the Solution Tank by pulling up on the round cap.
2. Add BISSELL Little Green Formula to the 'FORMULA' fill line (8-oz.).
3. Fill with hot (NOT boiling) tap water to the 'WATER' fill line.
4. Replace the cap before placing the Solution Tank back into the unit.
5. Replace the Solution Tank by inserting the bottom first into the cavity, then tilting it and pressing gently at the top until it snaps closed.

Diagram showing the Solution Tank with 'Water Fill Line' and 'Formula Fill Line' indicated. A separate illustration shows the Collection Tank.

Collection Tank

The Collection Tank is the translucent tank located on the left side of the unit. It is removed and replaced similarly to the Solution Tank. Empty the Collection Tank after each use, when dirty water reaches the indicated maximum fill line, or as instructed.

Vacuum Flex Hose with Grip/Trigger Unit

Store in the on-board hose storage on the back of the Little Green. Cleaning tools attach to the Grip/Trigger unit.

Power Cord

The cord, with a three-prong grounded plug, stores in the On Board Cord Storage at the bottom of the Little Green. Note: Unwrap Power Cord completely before operating the unit.

Built-in Heater (Not included with all models)

With the Little Green ProHeat models, you can turn the built-in heater on or off. The heater raises water temperature for improved cleaning performance. To use the heater, first turn the Power Switch ON, then turn the Heater Switch ON. Within 30 seconds, the Heat Indicator Light will illuminate. Begin using by depressing the Spray Trigger. Wait 5-10 seconds for non-heated water and solution to travel through the Flex Hose. After 5-10 seconds, the heated water and solution mixture is ready to be applied. See Page 8 for cleaning instructions.

Diagram showing the control panel with 'Power Switch' and 'Heater Switch' and 'Heat Indicator Light'.

Specialized Cleaning Tools

Depending on your model, your Little Green may be equipped with one or more of these tools:

• 1. 4" wide Cleaning Tool (included with all models): For cleaning carpet, upholstery, and spot cleaning.
• 2. Spraying Crevice Tool: For cleaning in tight areas.
• 3. 6" wide Cleaning Tool: For larger areas.
• 4. TurboBrush Cleaning Tool: Rotating brush for extra cleaning action for small areas, upholstery, and stairs.

To order optional tools not originally included, see "Part Numbers and Descriptions," page 9.

WARNING: Use only BISSELL Little Green formula in your cleaner. Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners or solvent-based soil removers should not be used. These products may react with the plastic materials used in your cleaner, causing cracking or pitting.

How To Deep Clean Carpet or Upholstery

Getting Ready

1. Remove Vacuum Flex Hose completely from On Board Hose Storage.
2. Attach 4" Tool, TurboBrush*, or Crevice Tool* to Grip Trigger Unit by pressing the Tool onto the Grip/Trigger Unit firmly, until the button snaps into the hole. Make certain the Tool is securely attached.
3. Unwrap Power Cord completely from On Board Cord Storage and plug into a 1230 Volt, 60 Hz grounded outlet as described in Important Safety Instructions, page 3.
4. Turn Power switch to ON Position.
5. Note: If your Little Green has a built-in heater, refer to instructions on page 7.
6. Press and hold Spray Trigger on Grip/Trigger unit. Spray will start in a few seconds.
7. Raise the Tool slightly to check for spray. If spray does not start, press firmly on the front of the Solution Tank while depressing Spray Trigger.

*Optional on some Little Green models. To order optional parts not originally included, call BISSELL Consumer Services at the telephone number listed on page 9.

Pre-treating

1. Pre-treat stained or highly soiled areas: Hold the flex hose with tool attached above carpet or upholstery, and pull trigger to spray cleaning solution.
2. Wait 3-5 minutes before cleaning.

WARNING: Be sure to unplug the cord before attaching the TurboBrush.

Deep Cleaning

1. Place the tool directly on the soiled surface at arm's length. Apply downward pressure on the tool and pull toward you, while pulling the trigger to spray cleaning solution.
   Note: If using the TurboBrush, the switch should be in the "BRUSH" position. This activates the brush only.
2. Repeat, keeping the tool firmly against the surface. Continue until no more dirt can be removed. Do not overwet.
   Note: If using the Turbobrush, move the switch to the "SUCTION" position. This activates the suction to remove the dirt and cleaning solution. Move the switch back to the "BRUSH" position for additional brushing action. Do not overwet.
3. Release spray trigger. Vacuum the area until no more cleaning solution can be removed.
   Note: If using the Turbobrush, move the switch to the "SUCTION" position. This activates the suction to remove the dirt and cleaning solution.
4. If the tool stops spraying, turn OFF Power Switch and check cleaning solution level. Refill if needed. Never run dry.

Diagram illustrating the TurboBrush tool with two modes indicated: 'BRUSH' for scrubbing action and 'SUCTION' for vacuuming up dirt and solution.

Deep Cleaning Upholstery

1. Check the manufacturer's tag before cleaning. "W" or "WS" on the tag means you can use your Little Green. If the tag is coded with an "S" (with a diagonal strike-through), or says "Dry Clean Only," do not proceed.
2. If the manufacturer's tag is missing or not coded, check with your furniture dealer.
3. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet.

Tip: Deep cleaning stairs and high traffic areas on a regular basis can prolong carpet life.

Tip: Check upholstery stuffing before cleaning. Colored stuffing may bleed through fabric when wet.

When You're Done

1. Turn Power Switch to OFF position.
2. Unplug Power Cord from outlet.
3. Remove and rinse Solution Tank, then replace.
   Note: If a significant amount of Little Green formula/water remains, you may leave it in the Solution Tank for your next cleaning task.
4. Remove Collection Tank, fill with clean water, rinse thoroughly, and discard, then replace.
5. Disconnect the tool from Grip/Trigger unit by pushing down on the button lock and pulling straight off (Do NOT twist tools to remove them).
6. Once removed from the Vacuum/Flex Hose, the tools can be cleaned: 4", 6", or Crevice tool - Rinse under clean running water. TurboBrush tool - Switch must be in "SUCTION" position. Rinse under clean running water.
7. Check Spray Nozzle for accumulated dirt or debris. If necessary, clean with a soft bristle brush.

Tip: Before turning off Little Green, vacuum up clean water to thoroughly rinse the Vacuum Hose. Then, lift the tool and point upwards. This allows any water still in the Hose to flow into the Collection Tank.

WARNING: Keep face away from spray. Failure to do so may result in personal injury.

Storage

1. Wipe all surfaces with a soft cloth.
2. Wrap Power Cord around Onboard Cord Storage at the bottom of Little Green.
3. Wrap Vacuum Flex Hose around Onboard Hose Storage and secure Grip/Trigger.
4. Store Cleaner in a protected, dry area, at room temperature (40° to 110°F).

Diagram showing the rear of the unit with 'Cord Storage' and 'Flex Hose' storage areas. A separate view shows the 'TurboBrush' attachment being stored on the back of the unit.

Note: For Little Green TurboBrush Models, on-board storage for the TurboBrush Tool has been provided on the back of the unit. Attach the TurboBrush to the unit by pressing onto the holder firmly until the button snaps into the hole.

Troubleshooting

WARNING: To reduce the risk of injury from moving parts and/or electrical shock, turn Power Switch OFF and disconnect polarized plug from electrical outlet before performing troubleshooting checks.

BISSELL Consumer Services

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services
1-800-237-7691

Monday - Friday: 8 a.m. - 7 p.m. EST
Saturday: 9 a.m. - 2 p.m. EST

Or write:

BISSELL HOMECARE, INC.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services

Or visit the BISSELL website: www.bissell.com

When contacting BISSELL, have your model number available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See "About Your Warranty" on page 12 for details.

Replacement Parts - BISSELL Little Green

Visual representation of the replacement parts, numbered 1 through 13, corresponding to the parts list table.

About Your Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.

Limited One Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product, BISSELL Homecare Inc. will repair or replace (with new or remanufactured components or products), at BISSELL's option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, or use not in accordance with the User's Guide is not covered.

If your BISSELL product should require service:

Call BISSELL Consumer Services at the number below or visit the BISSELL website www.bissell.com to locate a BISSELL Authorized Service Center in your area. If there are no authorized BISSELL Service Centers in your area, select the "Customer Service" tab, and follow the instructions for contacting us via email. A BISSELL Representative will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL for warranty repair.

The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is your proof of date of purchase in the event of a warranty claim - do not send original.)

If you need information about repairs or replacement parts, or if you have questions about your warranty, select the "Customer Service" tab on our website and follow the instructions for contacting us by e-mail.

Or call:

BISSELL Consumer Services
1-800-237-7691
Monday - Friday: 8 a.m. - 7 p.m. EST
Saturday: 9 a.m. - 2 p.m. EST

Or write:

BISSELL HOMECARE, INC.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services

BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL'S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.