Baseus Bowie MH1 Quick Start Guide

Contents

• Headphones × 1
• Carrying Case × 1
• Charging Cable × 1
• Quick Start Guide × 1
• Safety Instructions × 1

Specifications

Name: Baseus Wireless Noise Cancelling Headphones

Model: A02039

Input: 5 V=1.1 A

Full Charge Time: ≈ 1.5 hours

Frequency Response Range: 20 Hz – 40 kHz

Charging Port: USB-C

Bluetooth Maximum Output Power: -0.45 dBm for Eu

Frequency Band: 2402 MHz - 2480 MHz

*The above data is provided by the Baseus Lab; actual use will vary depending on the specific circumstances.

1. Warranty

Contact Us:

• Email: care@baseus.com
• Website: https://www.baseus.com
• Phone (US): +1 800 220 8056

The product comes with a 24-month warranty and lifetime tech support.

2. Powering On/Off

Press and hold the power button for 2 seconds to turn the headphones on or off. When turned on, the headphones enter pairing mode automatically (blue light flashes quickly).

3. Wearing

Adjust the headband and earcups for a comfortable and secure fit.

4. Pairing

Enable Bluetooth on your phone and select "Baseus Bowie MH1" from the device list. The headphones will remember the last connected devices and reconnect automatically when powered on.

5. Multipoint Pairing

1. Connect the headphones to device A. Then, turn off Bluetooth.
2. Connect the headphones to device B.
3. Turn on Bluetooth on device A; the headphones will automatically reconnect. Your multipoint connection is now ready.

6. Music & Call Controls

Single Press:

• Play/Pause music, Answer/End call

Press and Hold for 2 seconds:

• Power On/Off
• Activate Voice Assistant

Press and Hold for 2 seconds (Volume +/-):

• Volume Up/Down

Press and Hold for 2 seconds (Track +/-):

• Next/Previous Track

7. Sound Mode Controls

ANC Button (×1): Toggle ANC mode: Off (default) / On / Transparency

MFB Button (×2): Toggle spatial sound: Off (default) / On

MFB Button (×3): Activate voice assistant

8. App Control

Scan the QR code to download the Baseus App. Follow the in-app instructions to link your headphones and access custom settings. Ensure the headphones are near your device and the App is up to date.

9. Wired Mode

Use the included AUX cable to connect the headphones to your playback device. Noise cancelling and on-headphone volume controls remain available in wired mode.

10. Charging Your Headphones

Charging: Red light pulses.

Fully charged: Blue light stays solid.

11. Factory Reset

When the headphones are powered on, press and hold the "+" and "-" buttons for approximately 5 seconds; the red light will flash three times. This will reset headphones and restore custom settings in the App.

12. Support

For FAQs, detailed manuals, and more information, please visit: https://www.baseus.com/pages/support-center

13. Specifications

Name: Baseus Wireless Noise Cancelling Headphones

Model: A02039

Input: 5 V=1.1 A

Full Charge Time: ≈ 1.5 hours

Frequency Response Range: 20 Hz – 40 kHz

Charging Port: USB-C

Bluetooth Maximum Output Power: -0.45 dBm for Eu

Frequency Band: 2402 MHz - 2480 MHz

*The above data is provided by the Baseus Lab; actual use will vary depending on the specific circumstances.

Charging Power Requirements

The power delivered by the charger must be between a minimum of 2.5 Watts (required by the radio equipment) and a maximum of 5 Watts to achieve the maximum charging speed.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Battery Safety Information

Warning: Please follow the above safety instructions otherwise it will cause fire, electric shock, damage or other injuries.

• Replacement of a battery with an incorrect type can defeat its safeguard (e.g., for certain lithium battery types).
• Disposing of a battery in a fire or a hot oven or physically crushing or cutting it can lead to explosions.
• Leaving a battery in an environment with extremely high temperatures can cause explosions or the leakage of flammable liquid or gas.
• Using a battery in an environment with extremely low air pressure may result in explosions or flammable liquid or gas leakage.
• There is a risk of fire or explosion if the battery is replaced with an incorrect type.
• Avoid using the battery in extremely high or low temperatures and low air pressure at high altitudes during use, storage, or transportation.

Recycling Information

This symbol indicates that the product should not be disposed of with regular household waste. Please recycle it at designated collection points.

Manufacturer Information

Manufacturer: Shenzhen Baseus Technology Co., Ltd.

Address: 2nd Floor, Building B, Baseus Intelligence Park, No.2008, Xuegang Rd, Gangtou Community, Bantian Street, Longgang District, Shenzhen

Website: www.baseus.com(Global)

Support

If you need help, please contact us:

• (Global) +1 800 220 8056
• (Global) care@baseus.com