Proxim Stratum™ X5 Series Quick Installation Guide

Introduction

The Stratum™ X5 is a highly efficient radio endpoint delivering gigabit-plus throughput in point-to-point and multipoint wide area network configurations. It supports MIMO 4x4, with either integrated or external antennas (software switchable on some variants), making it suitable for high-capacity backhaul, high-resolution video surveillance, or high-density multipoint deployments. Powered by Proxim WORP® (Wireless Outdoor Router Protocol), managed via web GUI, CLI, Bluetooth-enabled Proxim BlueConnect™, and SNMP for ProximVision® Advanced, this high-speed platform offers advanced Quality of Service, granular service level management, and secure networking.

IMPORTANT! For regulatory information and latest product updates, including firmware and MIBs, visit Proxim's support site at http://support.proxim.com. The device must be installed by a trained professional familiar with radio frequency.

Products Covered in This Guide

This guide covers the following models:

• Stratum™ X5 Series SX5-1040A
• Stratum™ X5 Series SX5-1042A

Package Contents

Each shipment includes the items listed in the following table. Please verify that you have received all parts prior to installation.

Device Overview

The Stratum X5 Series devices feature the following ports and connectors:

SX5-1040A (Figure 1)

• Ethernet Port-1 (RJ45)
• Ethernet Port-2 (RJ45)
• SFP+ Port
• Access Port
• Antenna Ports (A1, A2, A3, A4) for 5 GHz connections. Connect A1 to Vertical Polarity, A2 to Horizontal Polarity, and A3/A4 to Slant Polarity ports for MIMO 4x4.
• GPS Connector for passive GPS antenna.
• LEDs for status indication (boot up, RSSI).
• Mounting Holes for mounting kits.
• Hose Clamp Slits for pole mounting (1/2 inch or 12 mm width).
• Grounding Points for device grounding.

Important: The Stratum X5-1042A includes a Quad polarization 18 dBi panel antenna by default. To use an external antenna, switch modes via BlueConnect application or Web GUI. Refer to the Device Management Guide for details.

SX5-1042A (Figure 2)

Similar port layout to SX5-1040A, with integrated antenna.

Device Features Table

Weatherproofing RJ45 Connection

Follow these steps to weatherproof the RJ45 connection:

1. Use an outdoor-rated CAT5e/CAT6 cable with straight-through termination on both ends.
2. Insert the cable through the Sealing Nut (D) and install the Compression Washer (C) onto the cable. The Compression Washer (C) has a slit for quick installation.
3. Install parts (D) and (C) as shown in Figure 3.
4. Insert the Flat Washer (A) onto the Connector Body (B), then insert the cable through Connector Body (B).
5. Connect the RJ45 connector end into the device's Ethernet port.
6. Ensure the locking latch of the RJ45 Connector is properly inserted into the Ethernet port.
7. Fasten the Connector Body Assembly to the device's Ethernet port and tighten fully.
8. Slide and insert the Compression Washer (C) into the Connector Body Assembly.
9. Fasten the Sealing Nut (D) to the Connector Body Assembly and fully tighten to weatherproof the cable.

Additional Weatherproofing Steps: For extra protection against the environment:

1. Wrap vinyl tape in a half-lapped fashion from the connector end down 3 inches onto the CAT5e/CAT6 cable.
2. Wrap butyl mastic tape over the adhesive side of the vinyl tape, covering it and the connector.
3. Wrap a final layer of vinyl tape over the butyl layer, covering the entire assembly.
4. Secure the assembly with a small zip tie to prevent unwrapping.

For detailed explanations of RJ45 and RP-SMA connections weatherproofing, refer to the Stratum™ X5 Series Hardware Installation Guide at http://support.proxim.com.

Assemble the Mounting Hardware

Follow these steps to assemble the mounting hardware:

1. Fix the Mounting Plate (A) to the bottom of the device using provided screws and washers. Ensure antennas will be vertically and horizontally polarized when mounted. Partially fasten screws with washers into all mounting holes before final tightening. Torque screws to 75 Lbf-in (86 Kgf-cm).
2. Fix the Extension Arm (B) to the Mounting Plate (A) with the provided bolt, nut, and washers. The Extension Arm (B) allows for greater tilt adjustment for azimuth or elevation.

Mount the Device

Pole Mounting:

1. Insert provided bolts through Bracket (D), mate with Bracket (C) around the pole, and secure with supplied washers. Torque to 100 Lbf-in (115 Kgf-cm). Supplied screws (Hex. Cap 5/16" x 4" long) fit pole diameters from 32 to 89 mm (1.25 to 3.5 inches).
2. Fix the Extension Arm (B) to the Mounting Bracket (C) with the provided bolt, nut, and washers. Partially tighten joints J1 and J2 for alignment.
3. Once alignment is satisfactory, tighten all assembled parts with a torque of 130 Lbf-in (150 Kgf-cm).
4. Ensure the device's Ethernet Port-1, with cable installed (using cable gland), faces downward as shown in Figure 5.

Wall Mounting:

1. Mount bracket (C) to a wall using 4 screws (not supplied), as shown in Figure 6.

Plug in the Cables

Note: Unscrew the sealing cap port cover before installing cables.

1. Plug one end of the straight-through Cat5e/CAT6 cable into the device's Ethernet Port-1, following the weatherproofing steps. Connect the other end to the OUT/PoE port on the PoE Injector.
2. Connecting a second Cat5e/CAT6 cable to Ethernet Port-2 is optional.

Note on Ethernet Port-2: 56V DC (30W max) is available on Ethernet Port-2. Ensure connected devices are rated for this voltage and power. When PoE IN receives 56V DC, PoE OUT delivers the same voltage. By default, Ethernet Port-2 is data-only; PoE OUT and Data can be enabled via Web configuration. Disconnect the cable from the PC before enabling this feature.

3. To connect via a hub or switch to a PC: Connect an Ethernet cable from the PC's network interface card to the hub, and from the hub to the RJ45 IN/LAN port on the PoE Injector.
4. To connect directly to a PC: Connect an Ethernet cable from the PC's network interface card to the RJ45 IN/LAN port on the PoE Injector.
5. The PoE Power Injector is a Gigabit Ethernet port and can supply up to 60 Watts.

Note: An optional 2.5/5 Gbps 802.3bt PoE injector (Part Number: 949-00147) is available separately.

Install Surge Protector

The Stratum™ X5 Series has built-in Ethernet surge protection. However, installing an approved lightning surge protector at the building ingress point is mandatory. For regions with severe weather, an additional surge protector near the device is recommended.

Note: An additional Surge Protector (Part Number: 235-00001) can be ordered separately.

Surge Protection Steps:

1. Mount a surge protector near the building ingress. Use a 10 AWG or larger wire to connect its ground lug to earth ground.
2. Ensure the outdoor device and the co-located surge protector share a common grounding point using the shortest possible grounding cable.
3. Connect an RJ45 terminated cable between indoor equipment and the surge protector's port at the building ingress.
4. Connect an RJ45 terminated cable between the surge protector and the outdoor device on Ethernet Port-1. IMPORTANT: Loop the cable before entering the premise to prevent water ingress.

Grounding Guidelines:

1. A proper earth ground impedance should be less than 1.0 ohm.
2. Measure ground impedance at the surge protector's ground wire connection point, not at the grounding rod.
3. Connect the surge protector ground wire and equipment ground (power and telecomm) to a single common ground.
4. Ensure all connections are securely fastened and tight.
5. Never install during a storm and always follow local safety codes.

Ground the Device

To ensure proper grounding, attach a ground wire (at least 12 AWG stranded) to one of the device's bottom corner ground points using the provided grounding screw. Follow these guidelines to protect against lightning or ESD events:

1. Connect one end of the grounding cable to the device and the other end to the closest earth ground point at the installation site.
2. Remove any excess ground wire length after connecting to the single point earth ground.
3. Avoid sharp bends, loops, or coiling the ground wire; connect it straight to ground.

Power on the Device

After connecting the PoE Injector and device with a CAT5e/CAT6 cable, plug the power cord into a power outlet. The device has no ON/OFF switch. To power down, unplug the RJ45 connector from the OUT/POE port on the PoE injector.

View LEDs

When powered on, the device performs startup diagnostics. Upon completion, Ethernet LEDs indicate the device's Ethernet state.

Power & Link LEDs (Figure 7)

RSSI LED Behavior (Figure 8)

During the first two minutes after power-on or reboot, LED indicators provide status:

Initialize the Device

Configure the device's IP address using HTTP, SNMP, CLI, or Proxim's ScanTool. For remote management with Proxim BlueConnect, refer to the Device Management Guide at http://support.proxim.com.

Default Access Values:

• Bluetooth Key: 123456
• Default IP address: 169.254.128.132
• Subnet Mask: 255.255.255.0
• Gateway: 169.254.128.132
• Username: admin
• Password: public
• SNMP Read Write Community String: public

Download Software and Documentation

Download software and documentation from the Proxim support site at http://support.proxim.com. Select "Stratum™ X5 Series" from the Product Downloads Page to find links for the latest software, SNMP MIB files, and documentation. Acrobat Reader is required for PDF documents.

Technical Support

Proxim Customer Support website: http://support.proxim.com (available 24x7x365).

Telephone Support:

• US and Canada: +1-408-383-7700; +1-866-674-6626
• International: +1-408-383-7700

Business Hours: Tier 1 support: 24x7 live response. Tier 3 support: 8 a.m. to 5 p.m. M-F PST (UTC/GMT -7 hrs).