Sunforce Solar String Lights with Remote Control

Product Overview

This document provides assembly and installation instructions for the Sunforce Solar String Lights with Remote Control. It includes product features, safety information, operational guidance, battery replacement, and frequently asked questions.

Package Contents

The kit includes the following components:

Safety Information & Warnings

⚠️ WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN.

General Safety:

• This solar string light is not a toy. Keep out of reach of small children.
• The solar string lights and solar panel are weather-resistant.
• The solar panel must be mounted outdoors for maximum sun exposure.
• Lay out all components before installation and check against the parts list.
• Never look directly into the solar string lights when illuminated.
• Do not hang other objects on the string lights.
• Do not cut or modify the wiring of the solar string lights.
• Before hanging bulbs, ensure they do not rest on hot surfaces or where they could be damaged. If charging batteries without bulbs attached, store bulbs safely indoors.

Battery Safety:

• Always purchase the correct size and grade of battery for the intended use.
• Always replace all batteries at the same time; do not mix old and new batteries or different types.
• Clean battery contacts and device contacts before installation.
• Ensure batteries are installed correctly with regard to polarity (+ and -).
• Remove batteries from equipment not used for extended periods.
• Remove and replace any defective or 'dead' batteries immediately.

⚠️ WARNING: This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.

• Swallowing may lead to serious injury or death due to chemical burns and potential perforation of the esophagus.
• If you suspect a child has swallowed or inserted a button battery, seek urgent medical assistance.
• Ensure battery compartments are securely fastened. Do not use if a compartment is not secure.
• Dispose of used button batteries immediately and safely; flat batteries can still be dangerous.
• Inform others about the risks associated with button batteries and how to keep children safe.

Product Features

• Vintage looking Edison LED light bulbs (E26 base)
• Integrated mounting loops
• Solar battery charging
• 10.67 m / 35 ft total cable length
• Remote control included
• 3V, 0.3W LED replaceable bulbs

Pre-Installation

1. Bulbs may be packed separately. Carefully remove bulbs from the box and insert into the string sockets. Screw tightly to ensure a proper connection.

   a) Connect the solar panel to the string lights connector.

   b) Select ON on the back of the solar panel.

   c) The bulbs should now illuminate.

   Once bulbs are illuminated, turn the solar panel switch to OFF and continue with installation.

2. Ensure the solar panel is positioned for optimal sunlight exposure. Be aware of objects like trees or building overhangs that may impede charging.

   [Illustration showing solar panel placement with potential obstructions]

3. Before first use, the solar panel needs 3 days of initial sunlight charge. This should be done with the string lights disconnected or the solar panel in the OFF position. After 3 days, the included batteries will be fully charged.

   The solar panel should be mounted where the ON/OFF switch is easily accessible.

Installation

Mounting the Solar Panel

The solar panel can be mounted using two options:

Option 1: Mounting Bracket (Wall/Surface Mount)

1. If needed, use the two wall plugs (H) and two large screws (G). Install screws through the outer holes of the mounting bracket (E) to secure it to the chosen surface.
2. Attach the mounting base (D) to the back of the solar panel (B) using the small screw (F).
3. Slide the solar panel down onto the mounting bracket (E) until it clicks securely into place.
4. Adjust the solar panel to the desired angle for optimal sun exposure.
5. The angle can be further adjusted by loosening, adjusting, and re-tightening the side screw on the panel's arm.

Option 2: Ground Stake Mount

1. Assemble the two parts of the ground stake (C).
2. The grooved section of the stake fits into the protruding arm of the solar panel's mounting base (D).
3. Insert the assembled stake into the ground.
4. Attach the solar panel (B) to the mounting base (D) using the small screw (F).
5. Slide the solar panel onto the stake's arm until it clicks.
6. Adjust the solar panel angle for optimal sun exposure.

To disconnect the solar panel from the mounting bracket, press the release tab on the bottom of the bracket and slide the panel upwards.

Installing the Solar String Lights

The solar string lights can be mounted in various ways:

1. Temporary Mounting: Use standard S hooks (not included) or screw hooks (not included) attached to the integrated mounting loops.
   [Illustration of temporary mounting with S hooks]
2. Permanent Mounting: Use cable ties or 'zip ties' (not included), or nails/screws into a surface, attached to the integrated mounting loops.
   [Illustration of permanent mounting with ties/screws]
3. Guide Wire Installation: Attach the string lights to a pre-installed guide wire (not included) using S hooks (not included).
   [Illustration of guide wire installation]
4. Decorative Installation: For a draped effect, attach the first bulb to a structure, then attach every 3rd or 4th bulb, and finally attach the last bulb to a structure.
   [Illustration of decorative draping installation]

Final Connection

1. Connect the solar panel to the string lights. Insert the plug located after the final bulb into the wire from the solar panel. Tighten the seal over the connection point by screwing it on.

The solar string lights will illuminate for 4-5 hours depending on battery charge level.

Operation

After an initial 3-day charge in the OFF position, the solar string lights are ready for use.

1. Pull out the plastic tab from the remote control (J) battery to activate it.
2. Solar Panel Switch:
   • ON: When the solar panel is in the ON position, the bulbs should illuminate.
   • OFF: Turns off the lights and disengages the remote control. Use for storage or long periods of inactivity.
   • AUTO: Automatically turns the lights on at night.
   ON
   [Lights on]

   OFF
   [Lights off]

   AUTO
   [Automatic night on]
3. Remote Control:
   • Press the button on the remote control to turn the bulbs OFF.
   • Press the button on the remote control to turn the bulbs ON.
   [Illustration of remote control with ON/OFF button]

It is advisable to leave the solar panel in the ON position for regular usage. Turning the solar panel to OFF disengages the remote control.

Battery Replacement

Solar Panel Batteries

The solar string light batteries (I) are located on the rear of the solar panel.

1. Always set the AUTO/ON/OFF switch to the OFF position before opening the battery compartment.
2. Unscrew the back of the battery compartment and remove the backing piece to access the batteries.
3. When replacing batteries, observe correct polarity and match battery specifications.
4. Use rechargeable batteries only. This product requires two rechargeable 18650 3.7V lithium-ion batteries.
5. Replace the battery compartment cover and resume use.

Remote Control Button Battery

The remote control (K) uses a 3V CR2025 lithium button battery.

1. Locate the battery compartment on the back of the remote control.
2. Identify and remove the small metal screw holding the compartment closed.
3. Follow the directional arrow on the remote to push open the compartment and expose the battery.
4. Replace the battery, ensuring correct polarity and that the new battery has the same characteristics as the old one.

Care & Maintenance

• Ensure the solar panel is positioned to optimize sun exposure, especially during winter months.
• Clean the solar panel regularly with a damp cotton cloth for optimal performance and charging.
• Use the same technique to clean the light bulbs.
• Never allow abrasive materials to contact the solar panel or bulbs.

Frequently Asked Questions (FAQ)

1. Q: Can the wire be extended? A: No, the solar string light's wiring cannot be extended.
2. Q: Do the solar string lights require direct sun to operate? A: The solar string lights will charge in direct and indirect sunlight. For optimal performance, orient the solar panel towards maximum sun exposure.
3. Q: Are the bulbs replaceable? A: Yes, the 0.3W LED bulbs are replaceable. Contact customer service for replacement information.
4. Q: Why do the solar string lights appear to strobe or flash? A: Flashing lights are usually caused by an undercharged battery. Turn the lights to OFF, charge for two full days in strong sun, then switch to ON.
5. Q: Can the solar string lights be used during the daytime? A: Yes, the bulbs can work during the daytime.
6. Q: What type of battery do my solar string lights require? A: Two rechargeable 18650 3.7V Li-Ion batteries.
7. Q: What type of battery does my remote control require? A: A 3V lithium (CR2025) button cell battery.
8. Q: How long do the lights illuminate for? A: Dependent on battery charge and health, the lights should illuminate for 4-5 hours.
9. Q: How do I make the lights come on automatically without the remote at night? A: Select the AUTO mode. The lights will illuminate automatically at night for up to 5 hours.

How to Replace the Bulb

Input: 3V, 0.3W | Edison LED Bulb with E26 base

1. Step 1: Carefully unscrew the light bulb.
   [Illustration of unscrewing a bulb]
2. Step 2: Completely remove the light bulb.
   [Illustration of removing a bulb]
3. Step 3: Carefully screw in the replacement bulb.
   [Illustration of screwing in a new bulb]
4. Step 4: Once the bulb is securely screwed in, it is ready for use.
   [Illustration of a securely installed bulb]

Only use 3V, 0.3W LED bulbs. For more information on replacement bulbs, contact Sunforce Products Inc. at info@sunforceproducts.com or call 1-888-478-6435.