Sunforce Solar Motion Activated Security Light

Product Overview

The Sunforce Solar Motion Activated Security Light provides bright illumination powered by solar energy. It features an adjustable motion sensor and dual brightness settings for versatile use in outdoor security and lighting applications.

Dimensions:

• Light Fixture: 16 cm (6.3 inches)
• Solar Panel: 20.9 cm (8.2 inches) x 11.6 cm (4.5 inches)
• Overall Width (Light Fixture): 32.5 cm (12.8 inches)
• Depth (Light Fixture): 11.1 cm (4.4 inches)
• Wire Length: 4.5 meters (14.7 feet)

Included Components:

• 1 x Motion-activated light fixture
• 1 x Solar panel
• 1 x Wire (4.5 m / 14.7 ft)
• 2 x Rechargeable 18650 3.7V Lithium-ion batteries (pre-installed)
• 5 x Mounting screws
• 5 x Wall plugs

Safety Information & Cautions

Safety Cautions

• This product is not a toy; keep out of reach of small children.
• The light and solar panel are weather-resistant.
• The solar panel must be installed outdoors to receive sunlight.
• Installation may require a second person, especially if using a ladder.
• Ensure all components are present and match the parts diagram before installation.
• Never look directly into the light when it is illuminated.

Battery Cautions

• Use only rechargeable batteries (18650 3.7V Lithium-ion recommended).
• Always replace all batteries simultaneously.
• Clean battery contacts and device contacts before installation.
• Ensure correct battery polarity (+ and -).
• Remove batteries from equipment not in use for extended periods.
• Promptly remove and replace any defective or "dead" batteries.
• Follow local regulations for battery recycling and disposal.

Care and Maintenance

• Periodically check the connection between the solar panel and the light fixture.
• Adjust the solar panel angle to maximize sun exposure, particularly during winter months.
• Clean the solar panel regularly with a damp cotton cloth to ensure optimal performance and battery charging.
• Periodically clean the motion light lenses using the same method.
• Avoid contact with abrasive materials on the solar panel.

Product Features

• Super bright white LEDs
• Adjustable motion sensor
• Frosted lenses for diffused light
• Adjustable time and distance settings for motion detection
• Dual brightness settings: 1000 Lumens (minimum) or 2000 Lumens (maximum)
• Solar panel with 4.5 m (14.7 ft) wire
• Easy mounting solution

Installation Guide

Pre-Installation Steps

• TEST Mode: Before final installation, set the light to TEST mode. The light will turn on and then off. Wave your hand in front of the motion sensor to confirm it activates, indicating the light is working correctly.
• It is important to ensure the light is only in TEST mode during initial installation or when troubleshooting.

Installation Steps

1. Mounting the Solar Panel

   Position the solar panel for optimal sun exposure, considering potential obstructions like trees or property overhangs. If necessary, use a power drill (not included) to create mounting holes. Secure the solar panel to the chosen surface using 3 of the included wall plugs and screws.

2. Attaching the Mounting Bracket

   Using 2 wall plugs and screws, fix the mounting bracket securely to the chosen surface.

3. Mounting the Light Fixture

   Slide the light fixture onto the mounting bracket until it is securely in place. To disconnect the light from the bracket, depress the release tab located on the bottom of the mounting bracket and slide the light upwards. Some force may be required.

4. Connecting the Power

   Connect the wire from the solar panel to the socket located under the light fixture. Your solar motion light will now begin to charge.

5. Adjusting Lamp Heads

   Once the motion light is installed, the lamp heads can be adjusted independently in various ways to provide optimal lighting coverage.

6. Setting Controls

   Two switches allow adjustment of the light's illumination time and motion detection range:

   • TIME: Determines the duration the light stays on after motion is detected: 30 seconds, 60 seconds, or 120 seconds.
   • DISTANCE: Controls the range of motion detection: Low, Medium, or High.
   • DUAL BRIGHTNESS FUNCTION: This solar security light allows for changing the lumen output by sliding this switch. Select either 1000 Lumens (minimum brightness) or 2000 Lumens (maximum brightness).

   Note: The TEST function allows positioning of the motion sensor. Once positioned correctly, set the switch to the preferred duration option. The light will now only turn on in darkness.

7. Initial Charging and Operation

   Before using your solar motion light, the solar panel needs to be connected to the light for a period of three days. This initial charge should be done with the light in the OFF position. After the third day, the included batteries will be fully charged, and your solar motion light is ready for operation.

   Select the desired brightness of the light (1000 or 2000 lumens) and proceed to select TIME and DISTANCE. Your solar motion light is ready to operate at night.

   Batteries are located in the battery housing behind the light fixture. Select the OFF position on the light before opening the battery housing. Remove the four screws to access the batteries. Refer to the "CAUTIONS: BATTERY INSTRUCTIONS" section for information on replacing the batteries.

Frequently Asked Questions (FAQ)

• Q: Where should the solar panel be mounted?
  A: Mount your solar panel in a position that will enable the most amount of light to be absorbed (refer to Step 1). In the Northern Hemisphere, this is usually south-facing.
• Q: Does the solar panel require direct sun to charge?
  A: The solar panel can charge the internal batteries in direct and indirect light. For best results, optimize your solar panel's sun exposure.
• Q: Can additional or extended cable wire for the solar panel be purchased?
  A: At this point, there are no extensions available for the cable that connects the light to the solar panel.
• Q: Why does the solar motion light appear to "strobe" or flash?
  A: A rapidly flashing light is caused by undercharged batteries. Turn the solar motion light to the "OFF" position and charge for two full sunny days to bring the batteries to full charge.
• Q: Will decorative or street lights have an effect on the motion sensor's ability to operate?
  A: Yes, the sensor of the solar motion light is light-sensitive. For nighttime usage, ensure no other light interferes with the motion sensor.
• Q: What type of battery does my solar motion light require to operate?
  A: For optimal performance, your solar motion light requires the use of two rechargeable 3.7V Lithium-ion batteries.
• Q: Can this light be used to come on automatically at dusk and turn off in the morning?
  A: No, this solar motion light is activated only by motion; it does not have a dusk-to-dawn feature.