IRONBISON
Instruction Manual for IRONBISON models including: IBDS-C001 Running Boards Side Steps, IBDS-C001, Running Boards Side Steps, Boards Side Steps, Side Steps
IRONBISON Running Boards Side Steps Fit 2015-2024 Chevy Colorado/GMC Canyon Crew Cab Pickup Truck Nerf Bars Drop Steps Off-Road Rock Slider Fine Textured Black : Automotive
File Info : application/pdf, 4 Pages, 556.96KB
DocumentDocumentDefender Step PART NO. IBDS-C001 FITS: 2015-Up Chevy Colorado Crew Cab 2015-Up GMC Canyon Crew Cab 60-120 min Cutting Not Required Drilling Not Required Torque & Tools Fastener Size 6mm 8mm 10mm 12mm Tightening Torque (ft-lbs) 7-8.5 18-20 35-40 60-70 Wrench Required 10mm 13mm 16mm 18mm Allen Wrench Required 4mm 5mm 6mm 8mm BEFORE INSTALLATION REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. RUNNING BOARD IS HEAVY, ASSISTANCE IS HIGHLY RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE. Part List Driver / Left Side Front Passenger / Right Side Mounting tabs approx. 23 inches apart Mounting tabs approx. 40 inches apart Driver/left Mounting Bracket x 3 Passenger/Right Mounting Bracket x 3 www.ironbisonauto.com Customer Support: service@ironbisonauto.com x12 8mm x 30mm Hex Bolt x6 8mm Bolt/Nut Plate x18 8mm x 24mm Flat Washer x18 8mm Lock Washer x6 8mm Hex Nut x6 8mm Plastic Retainer x12 8mm Clip Nut x6 8mm x 25mm Combo Bolt PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER SIDE INSTALLATION STEP 1 Start the installation under the Driver/Left side of the vehicle. Locate the front mounting location along the bottom and inner side of the body panel, (Fig 1). Installation will use the 1st, 2nd and 4th mounting locations. NOTE: It may help to hold a Bracket up in place to help determine the mounting holes to use along the bottom and inner side of the body. FIG 1 Front 4 2 1 (Fig 1) Driver side mounting locations along bottom and back of body panel illustrated STEP 2 Remove rubber plugs as necessary from the holes in the side and bottom of the inner body panel, (Fig 2). FIG 2 Front (Fig 2) Remove rubber plugs from front and center mounting locations (arrows) STEP 3 Select (2) 8mm Clip Nuts. Slide each Clip Nut into the large hole and over the smaller hole next to it. Line up threaded nut on the Clip Nut with smaller hole in body panel, (Fig 3) www.ironbisonauto.com Page 1 of 3 Rev. 6/14/23 (JH) FIG 3 Front (2) 8mm Clip Nuts (Fig 3) Slide 8mm Clip Nut into large hole and over small hole STEP 4 Select (1) Driver/Left Mounting Bracket. Attach the Mounting Bracket to the (2) Clip Nuts in the vehicle with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Fig 4). Do not tighten hardware. FIG 4 STEP 5 Repeat Steps 1--4 to attach the remaining (2) Driver/Left Mounting Bracket to the center and rear locations, (Figs 5 & 6). Do not tighten hardware. FIG 5 Front (Fig 5) Driver/left side center mounting location FIG 6 (2) 8mm Hex Bolts (2) 8mm Lock Washers (2) 8mm Flat Washers (2) 8mm Clip Nuts (Fig 4) Attach (1) Driver/Left Mounting Bracket to the Clip Nuts Rear (Fig 6) Driver/left side rear mounting location www.ironbisonauto.com Page 2 of 3 Rev. 6/14/23 (JH) STEP 6 Select the Driver/Left Running Board. Insert (1) 8mm Bolt/Nut Plate into the front mounting tabs on the Running Board. Thread (1) 8mm Plastic Retainer onto the threads of the Bolt/Nut Plate to hold it in place (Fig 7). Do not tighten hardware. FIG 7 (1) 8mm Plastic Retainer Front (1) 8mm Bolt/Nut Plate (Fig 7) Insert (1) 8mm Bolt/Nut Plate into the mounting tabs of the Running Board STEP 7 Repeat Step 6 insert (2) 8mm Bolt/Nut Plates into the center and rear mounting tabs. STEP 8 Attach the Running Board to the (3) Mounting Brackets with (3) 8mm Flat Washers, (3) 8mm Lock Washers, (3) 8mm Hex Nuts and (3) 8mm Combo Bolts, (Fig 8). Do not tighten hardware. FIG 8 (1) 8mm Hex Nut (1) 8mm Lock Washer (1) 8mm Flat Washer (1) 8mm Combo Bolt (Fig 8) Attach the Driver/Left Running Board to the Mounting Brackets STEP 9 Level and adjust the Running Board and fully tighten all hardware. STEP 10 Repeat Steps 1--9 to attach the Passenger/Right Running Board. STEP 11 Do periodic inspections to the installation to make sure that all hardware is secure and tight. Attention To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Boards. www.ironbisonauto.com Page 3 of 3 Rev. 6/14/23 (JH)