Front Runner Hi-Lift Jack Bracket
Model: JADA010
READ ME!
Thank you for purchasing a Front Runner Hi-Lift Jack Bracket. Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities, and tools required.
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.
1 GET ORGANIZED
Here is what you are looking at for JADA010
IN THE BOX
- 1 X M10x40 Hex Bolt
- 3 X M10x30x3 Flat Washer
- 4 X M8x25 Button Head Bolt (Black)
- 10 X M8x16x1.6 SS Flat Washer
- 1 X Base Bracket
- 1 X M10 Wing Nut
- 1 X M12 Nyloc Hex Nut
- 1 X M12 Flat Washer
- 8 X M8 Nyloc Hex Nut
- 2 X M8x16 Button Head Bolt (Black)
- 1 X M12 Machined Stud
- 2 X Support Bracket
- 1 X Handle Clamp Assembly
- 1 X M10 Tie Down Ring
- 2 X M8x20 Button Head Bolt (Black)
IN THE BOX CONTINUED
- 2 X M8x30 Button Head Bolt (Black)
- 2 X M8 Nut Cap
- 2 X M8 x 20 Hex Bolt
TOOLS NEEDED
- Allen Key (4mm, 5mm)
- Marker
This diagram shows an exploded view of the Front Runner Hi-Lift Jack Bracket components. It lists 20 numbered parts, including various bolts (M10x40 Hex Bolt, M8x25 Button Head Bolt, M8x16 Button Head Bolt, M8x20 Button Head Bolt, M8x30 Button Head Bolt, M8 x 20 Hex Bolt), washers (M10x30x3 Flat Washer, M8x16x1.6 SS Flat Washer, M12 Flat Washer), nuts (M10 Wing Nut, M12 Nyloc Hex Nut, M8 Nyloc Hex Nut), brackets (Base Bracket, Support Bracket), a Handle Clamp Assembly, an M10 Tie Down Ring, and an M12 Machined Stud. It also indicates required tools: an Allen Key (4mm and 5mm) and a Marker.
1 GET ORGANIZED CONTINUED
This diagram provides another perspective of the assembly, showing how the Handle Clamp Assembly (15), M10 Tie Down Ring (16), and other bracket components are put together. It illustrates the connection points for various bolts and nuts.
2 RECOMMENDED POSITIONS
2.1
Please note that it is not recommended to mount your Hi-Lift Jack on the front or rear of your Rack, only on the sides. For ease of instruction, we have chosen to describe one orientation of mounting the Jack Bracket. The principles are the same; just the positioning and orientation of the brackets may vary depending on where you want to mount the jack.
Decide where on your Rack you would like to mount the Hi-Lift Jack. The brackets can be orientated upwards, downwards, front to back, and back to front. Refer to Page 4, showing the various mounting options.
2.2
This diagram displays two views of a roof rack. Each view shows the rack with several mounting points indicated by an 'X'. A prominent warning symbol (⚠️) is displayed next to the text "THIS POSITION IS NOT SUITED FOR A HI LIFT JACK." The 'X' marks on the diagrams illustrate these unsuitable mounting locations.
⚠️ THIS POSITION IS NOT SUITED FOR A HI LIFT JACK.
3 FIT AND SECURE
3.1 Fit and Secure Base Bracket
Fit and Secure Base Bracket in desired position as shown.
Diagram 3.1: Fitting the Base Bracket. Shows the Base Bracket (5) being attached to a roof rack slat. Fasteners used include M10x40 Hex Bolt (1) and M8x16x1.6 SS Flat Washer (4), secured with an M8x30 Button Head Bolt (18). The text indicates "REMOVE FROM SLAT" and specifies 13mm and 5mm wrench sizes.
3.2 Secure Bracket
Secure as shown. Insert 2 M8 Hex Nuts at the point indicated by the arrow.
Diagram 3.2: Securing the bracket with nuts. Illustrates securing the bracket to the rack. It shows M8x25 Button Head Bolt (3), M8x16x1.6 SS Flat Washer (4), M8x20 Button Head Bolt (20), and Support Bracket (14). The text states, "Secure as shown. Insert 2 M8 Hex Nuts at the point indicated by the arrow."
3.3 Assemble Pin and Bolt
Assemble the machined pin and securing bolt in hole pattern suited to your jack.
Diagram 3.3: Assembling the machined pin and securing bolt. Depicts the assembly of the main bracket structure. It shows the Base Bracket (5), M10x40 Hex Bolt (1), M10 Wing Nut (6), M12 Nyloc Hex Nut (7), M12 Flat Washer (8), and M12 Machined Stud (13). It mentions using 17mm and 5mm wrench sizes and assembling the machined pin and securing bolt into a hole pattern suited to the user's jack.
3.4 Attach Handle Clamp
Fit and Secure the handle clamp in the desired position, using fasteners shown in Figure 1.2.
Diagram 3.4: Attaching the handle clamp assembly. Shows the final attachment of the Handle Clamp Assembly (15) to the bracket. It uses M10 Tie Down Ring (16), M8x20 Button Head Bolt (17), and M8x16x1.6 SS Flat Washer (4). The text indicates using fasteners shown in Figure 1.2 and specifies 13mm and 5mm wrench sizes.
4 FINISH
Congratulations! You did it. Take a step back and admire your work!
5 INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
