LiftMaster STAR1000 Commercial Access Control Receiver
Application
The STAR1000 is a high capacity single channel commercial access control receiver for commercial door operators and dry contact triggered devices. The STAR1000 is compatible with Security+ 2.0™ remote controls and wireless keyless entries, Security+ 2.0™ Passport and Passport Lite remote controls. This receiver is compatible with HomeLink®. For programming or compatibility information, visit www.homelink.com. The receiver capacity is 1,000 devices and can be any combination of remote controls and wireless keyless entries. The receiver is watertight according to IPX44 specification.
Installation
Select Location
Select a convenient location near the operator to be controlled by the receiver within "line of sight" of the intended transmitting location. Note: Do not mount the LCD screen in direct sunlight. Avoid mounting the receiver in a metal enclosure or near other wireless receiving or transmitting devices.
Mount Bracket
Mount the bracket to the desired surface with appropriate hardware (not provided) (See Figure 1).
Prepare Receiver
Remove the 4 (#8) screws on the back of the receiver and remove the faceplate. Unplug the keypad connector from the control board. Note: Be careful not to damage the keypad cable while removing the faceplate.
Make Wiring Connections
Make wiring connections (See Figure 2). Refer to your gate or commercial door operator owner's manual for more specific information.
Reconnect Keypad
Reconnect the keypad connector to the board (labeled J9).
Secure Faceplate
Secure the faceplate with the 4 (#8) screws previously removed.
Install Antenna
Install the antenna provided. Note: Use the optional 86LM or 86LMT antenna extension kit (see page 4) to mount the remote antenna as high and far from metallic objects as possible for best radio range.
Mount Receiver
Snap the receiver onto the mounting bracket and secure with the (#8) screws provided.
Seal Wiring
Tighten the watertight connector to secure and seal the wiring.
Figure 1: Receiver Components
Figure 1 illustrates the components of the STAR1000 receiver. It shows the Keypad Connector, Backup Memory Module, Antenna Connector, Mounting Bracket, and Watertight Connector. The receiver is shown without its faceplate.
Figure 2: Wiring Diagram
Figure 2 depicts the wiring connections for the STAR1000 receiver. It shows the Power Connection and Relay Connection terminals. The diagram illustrates the receiver connected to a 9-30 Volts AC/DC, 250 mA max Power Supply, a Control Station, and a Single Operator. It also indicates the Receiver without Faceplate.
Safety Warnings
WARNING: To prevent possible SERIOUS INJURY or DEATH from electrocution, be sure power is NOT connected BEFORE installing the receiver.
WARNING: To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
- ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.
- Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
- ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
WARNING: To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED. When a receiver is used to activate a commercial door opener, a reversing edge MUST be installed on the bottom of the door. Failure to install a reversing edge under these circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door.
User Interface
The STAR1000 user interface consists of a 22-character by 5-line LCD display, 3 "soft keys", Down/Up arrows, and a numeric keypad.
- LCD Display: Shows system programming and status.
- Line 1: Menu and function mode.
- Lines 2, 3, and 4: Menu selections and data.
- Line 5: Soft key function modes.
- Soft Keys: Functions are defined by the label on line 5 of the display and change according to menu selection.
- Down/Up Keys: Used for navigation in the menus.
- Numeric Keypad: Used for entering numeric data.
- Scroll Indicator: Appears on the left margin of lines 2, 3, and 4 if more than 3 options exist, showing relative position within the list.
- Antenna Connection: For the direct antenna or an antenna extension kit.
- Menu/Data Selection: Shown in inverse font.
Programming
The receiver can learn a combination of up to 1,000 remote control transmitters and keyless entries. Audible and visual warnings occur when capacity is exceeded. After 30 seconds of inactivity, the receiver times out and the LiftMaster® logo is displayed. Select "UNLOCK" and enter the PIN to continue.
Initial PIN Setup
The PIN restricts access to authorized administrators only. If omitted, anyone can program the receiver. Upon initial power-up, the system firmware revision is displayed for 5 seconds, followed by the LiftMaster® logo. Pressing a key displays "CREATE PIN?".
- Press "YES" to create a PIN.
- If the PIN is lost, request a reset code by pressing "RESET." You will be provided with a 5-digit serial number. Log in to the partner portal at https://partner.liftmaster.com/utility and enter the Serial Number to retrieve the master code.
- Enter a 6-digit PIN, then press "YES". Enter the 6-digit PIN a second time and press "YES" to program the PIN. Press "CLEAR" to correct errors. Select "BACK" to exit the PIN entry screen.
- Once the 6-digit PIN is programmed, the LCD reads "KEYPAD UNLOCKED". Select "OK" to proceed to the Main Menu. After 30 seconds of inactivity, the receiver times out and the LiftMaster® logo is displayed. Select "UNLOCK" and enter the PIN to continue.
Note: Resetting the PIN does not clear data or settings on the STAR1000 and PPWR.
Programming Commands
| Menu | Command | Description |
|---|---|---|
| MAIN MENU | LEARN DEVICE | Program a device to the receiver. |
| BLOCK LEARN DEVICE | Block program a range of devices to the receiver. | |
| LEARN TO LOC # | Program a device to a 4-digit number location. | |
| DELETE MENU | DELETE DEVICE | Delete a specified device that has been programmed to the receiver. |
| DELETE ALL DEVICES | Delete all programmed devices. | |
| SUSPEND MENU | SUSPEND DEVICE | Temporarily disables the function of a specified device that has been programmed to the receiver. |
| SUSPEND ALL DEVICES | Temporarily disables the function of ALL devices programmed to the receiver. | |
| UNSUSPEND DEVICE | Re-enable the function of a suspended device. | |
| UNSUSPEND ALL DEVICES | Re-enable the function of ALL suspended devices. | |
| QUERY MENU | LOC # USED | Displays a range of used locations starting from a specified location. |
| LOC # AVAILABLE | Displays a range of empty locations starting from a specified location. | |
| LOC # SUSPENDED | Displays a range of suspended locations starting from a specified location. | |
| SETTINGS | CHANGE PIN | Change the 6-digit PIN number for the receiver. |
| DEALER INFO | Display and edit the dealer 11-digit contact phone number. | |
| FIRMWARE VERSION | Displays the current firmware version. | |
| BEEP | Turn the audible feedback on or off. | |
| MEMORY | DUPLICATE MEMORY | Creates a memory backup. A backup memory module must be installed. |
| RESTORE MEMORY | Restores a memory backup from a memory module. Note: Content of memory backup module will over-write any information already stored in the receiver memory. | |
| RELAY | Sets the relay activation time from .25 to 1 second. | |
| CONTRAST | Press Down or Up arrows to adjust LCD contrast. | |
| LANGUAGE | Sets menu language: English (Default), Spanish, and French. | |
| FACTORY DEFAULT | Reset receiver to factory default settings. |
Diagnostics
The receiver emits a series of audible beeps to signal programming and error events. The On/Off column indicates that the audible notification for the event may be disabled in the BEEP SETTINGS menu.
| Event | Audible Notifications | On/Off |
|---|---|---|
| Key press | Single | YES |
| Successful Add | Double | |
| Successful Delete | Triple | |
| Successful Suspend | Double | |
| Successful Unsuspend | Double | |
| Master PIN entry error | Long | |
| Programming error | Long | |
| Location out of range | Long | |
| Generic Success | Double | |
| Generic Error | Long | |
| Received unknown Tx | Slow | YES |
| Received known Tx | Double | YES |
| Received known suspended Tx | Long | YES |
Specifications
| System Capacity | 1000 devices |
| Supply Voltage | 9 - 30 Volts AC, 9 - 42 Volts DC |
| Operating Current | 50 mA Maximum |
| Stand By Current | 30 mA Maximum |
| Surge Suppression | 6.0 kV Min |
| Operating Temp Range | -40°C to +65°C @ 50% Rh, -40°F to +149°F @ 50% Rh |
| Storage and Shipping Temp Range | -40°C to +85°C @ 50% Rh |
| Code Format | Security+ 2.0™ Only |
| Relay Contact Rating | 1 amp @ 24V AC/DC |
Compatible Accessories
| Remote Controls | 892LT, 894LT, 891LM, 893LM, 890MAX, 893MAX, PPV3M, PPK3M, PPK3PHM, PPLV1-xxx, PPLK1-xxx, PPLK1PH-xxx |
| Keypads | 877LM, 877MAX, and 878MAX |
| Antenna Extension Kits: | |
| 15' Extension Kits | 86LM |
| 25' Extension Kits | 86LMT |
| 24VAC Transformer for screw terminals | 95LM |
Repair Parts
| Antenna | K76-36681 |
| Mounting Bracket | K13-36651-1 |
Notice
To comply with FCC and/or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards for Home or office use. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Technical Support
For technical support, dial our toll-free number: 1-800-528-2806
