Cambridge Casual Teak Wicker Furniture Assembly and Care

General Information & Tips

Please read all assembly instructions before beginning. Assemble furniture on a non-abrasive surface like carpet to avoid damage. Ensure all bolts are tightly fastened before use. This furniture is not intended for commercial use.

Tools Required:

• 8" Philips screwdriver (Not provided)
• Rubber Mallet (Not provided)

Teak Wicker Sofa (IT-151178T)

Assembly Instructions:

Step 1: Attach back support (B) and back support holder (D), secure using 1 1/4" bolt (G). Tighten all bolts.

Step 2: Attach back support (B) and seat (C) into right side frame (A1), secure using 3 1/2" bolts (E) and 2" bolts (F). Tighten all bolts.

Step 3: Attach left side frame (A2) to the assembled frame. Secure using 3 1/2" bolts (E) and 2" bolts (F). Attach back support holder (D) and seat (C) using 1" screw (I). Tighten all bolts and screws.

Step 4: Ensure all parts are connected correctly and tighten all bolts. Tap wooden caps (H) to cover bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame.

Step 5: Install cushion and pillow. The sofa is now ready for use.

Teak Wicker Lounge Chair (IT-121617T)

Assembly Instructions:

Step 1: Attach back support (B) and seat (C) into right side frame (A1).

Step 2: Attach left side frame (A2) to the assembly from Step 1, secure using 2" bolts (D) and 3 1/2" bolt (E). Tighten all bolts.

Step 3: Invert the chair. Secure right side frame (A1) with 2" bolts (D) and 3 1/2" Bolt (E). Tighten all bolts and screws.

Step 4: Ensure all parts are connected correctly and tighten all bolts. Tap wooden caps (F) to cover bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame. The chair is now ready for use.

Teak Wicker Rocking Chair (IT-131050T)

Assembly Instructions:

Step 1: Attach front apron (D1) and back apron (D2) to Seat (C), then attach back support (B) into right side frame (A1).

Step 2: Attach left side frame (A2) to the assembly from Step 1, secure using 3 1/2" (E) and 2" bolts (F). Tighten all bolts.

Step 3: Upright the rocker and repeat the same procedure in Step 2 to secure right side frame (A1) using 3 1/2" bolt (E) and 2" bolts (F). Tighten all bolts and screws.

Step 4: Ensure all parts are connected correctly and tighten all bolts. Tap wooden caps (G) to cover bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame. The rocking chair is now ready for use.

Teak Wicker Ottoman (IT-280502T)

Assembly Instructions:

Step 1: Attach the stool (B) to leg frame (A), position as shown. Tighten bolts.

Step 2: Attach the other leg frame (A) to stool (B), position as shown. Secure using 2" bolts (C). Tighten bolts.

Step 3: Turn stool upright. Secure 2" bolts (C). Tighten bolts.

Step 4: Ensure all parts are correctly connected and tighten all bolts. Tap wooden caps (D) to cover bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame. The stool is now ready for use.

Teak Wicker Coffee Table (IT-70881T)

Assembly Instructions:

Step 1: Attach apron (D) into top table (B). Secure using 2 3/4" bolts (G), then attach into leg frame (A). Secure using 1 3/4" bolts (F). Tighten all bolts.

Step 2: Attach tray table (C) to the leg frame (A) secure using 1" bolts (E). Tighten all bolts.

Step 3: Attach the other leg frame (A) to previous assembly. Secure with 1" bolts (E) and 1 3/4" bolt (F). Tighten all bolts.

Step 4: Upright the table. Ensure all parts are correctly connected and tighten all bolts. Tap wooden caps (H) to cover bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame. The table is now ready for use.

Teak Wicker Side Table (IT-180881T)

Assembly Instructions:

Step 1: Attach apron (C) into top table (B), secure using 2 3/4" bolts (E). Tighten all bolts.

Step 2: Attach leg frame (A) to the assembly from Step 1, secure using 1 3/4" bolts (D). Tighten all bolts.

Step 3: Turn the table right side up. Ensure all parts are correctly connected and tighten all bolts. Tap wooden caps (F) to cover bolt heads using a rubber mallet. Tap carefully to avoid damaging the wood frame. The table is now ready for use.

Care Maintenance

General Outdoor Care:

• Regular cleaning is important.
• Use furniture covers or store in a covered location during inclement weather.
• Ensure furniture and cushions are clean and dry before covering or storing.
• Remove wet cushions and air dry to prevent mold and mildew.
• Do not store furniture in areas with direct heating or cooling vents.
• Avoid standing liquids on furniture surfaces.
• Do not place hot items directly on furniture.
• Do not write on furniture without a padded barrier.
• Do not leave furniture in puddles of water.

Unfinished Natural / Finely Sanded Teak:

• Natural variations in grain and color are normal.
• Small splits, knots, and joint lines contribute to character.
• Natural teak develops a silver-gray patina; teak sealer or oil can maintain the original color.
• Teak expands and contracts with climate changes, potentially causing hairline cracks in joints, which do not affect structural integrity.
• Surface mildew may form but does not impact durability and can be cleaned.

Care & Maintenance (Teak):

• Clean with warm water and mild dish soap, scrubbing with the grain. Rinse and air dry.
• For tougher stains, use a mixture of 1 cup chlorine bleach, 1 cup laundry detergent, and 1 gallon of water. Apply with a soft-bristle brush, let sit for 5-10 minutes, rinse thoroughly.
• Start with milder solutions; use stronger concentrations or teak cleaners if needed.
• For remaining stains, lightly sand with 120-grit sandpaper.

Weathered Teak:

• Hand-applied finish may fade and wear with outdoor exposure.
• Natural teak will be exposed and turn gray as the finish wears.
• Preserve weathered teak by moving to covered storage or using a furniture cover during extreme weather.

Spa Collection Teak:

• Maintained with solvent-based polyurethane protective coating every six months.
• For everyday maintenance, clean with mild detergent and a clean cloth. Avoid chemical solvents.

Painted Hardwood:

• Apply water-based mild detergent with a clean cloth every six months. Avoid chemical solvents.
• Color may fade with sun and rain exposure; store indoors or use a cover during extreme weather.

Cushions:

• Fabrics are breathable, water-resistant, but not waterproof.
• Remove and store cushions in a dry place when not in use or during inclement weather.
• Air dry wet cushions on their sides with the zipper down to ensure proper drainage.
• Clean off dust and dirt periodically; wipe spills immediately.
• Spot clean soon after stains occur.
• Removable cushion covers can be machine washed in cold water with mild soap and air dried.
• Periodically rotate cushions and pillows to distribute wear and prevent loss of shape.

Synthetic Rattan, Woven Polyrope, & Textilene:

• Dust periodically with a soft, dry cloth.
• Remove loose dirt with a soft, non-metallic bristle brush.
• For spot-cleaning, spray off debris with a hose and dry with a soft cloth.
• For thorough cleaning, use a mixture of mild soap and water with a soft-bristle brush. Do not use abrasive cleaners. Rinse and dry thoroughly.

1 Year Limited Warranty

This is a limited warranty for the original purchaser. If a product fails under the terms of the warranty, it will be replaced with a small fee. Discontinued models will be replaced with an item of similar quality and style.

1 Year Limited Frame Warranty:

• Wood frames are warranted against structural defects.
• User maintenance is required for wood frames; natural color changes are normal and not covered.
• Components like chair feet are subject to wear and tear and not covered.

Finish Warranty:

• The finish is warranted against peeling, cracking, or blistering for 1 year, provided the unit has not been scratched or abraded.
• Scratches and dents from normal wear and tear are not covered.

Fabric Warranty:

• Fabrics and cushions are warranted against workmanship or material defects.
• Failures due to chemical exposure, cleaning products, sun lotions, oil spills, improper maintenance, or extreme heat are not covered.

Warranty Exclusions:

• Commercial or non-residential use.
• Clearance items, display models, or "as is" purchases.
• Unreasonable or abusive use, freight damage, acts of nature, vandalism, fire.
• Lack of proper care and maintenance, improper assembly.
• Exposure to severe weather (snowstorm, hail, heavy rainfall, flooding, hurricane, extreme heat).
• Accidental damage, unauthorized repair or modifications.
• Fading or discoloration from exposure to elements, oil spills, fluids, or chemicals.
• Hardware corrosion or rusting.
• Buckling or splitting of tubing from exposure to water and freezing temperatures.
• Normal wear and tear, loss of use, inconvenience, money, travel, packaging, or consequential/incidental damages.

Manufacturer's responsibility does not exceed the product's value. Warranty starts on the date of purchase.

Claim Requirements:

• Packing slip / Invoice.
• Photos or video of damaged/defected/missing part.
• Item number and part code (found on assembly instructions).

Claims will not be processed without proper documentation. Retain all damaged goods until the claim is concluded. Warranty terms are subject to change without notice.