Contact Us
✉️ Email Us: Technical Support support@iliferobot.com
? Tweet Us: @ILIFEROBOTICS Mon-Fri: 9:00 AM - 6:00 PM
ILIFE Customer Service
Toll-Free Number: 1-800-631-9676 (Toll free for USA & Canada)
Monday-Friday from 9:00 AM - 5:00 PM CST
Before You Get Started | See How V5s Pro Works
Positioning the charging dock.
Place the charging dock, plug in its adapter, and ensure the signal light on the charging dock turns solid.
Tips: Position the charging dock against a wall. Remove obstacles approximately 1 meter (3.2 feet) to both sides and about 2 meters (6.5 feet) forward from the dock. (Visual representation: A diagram showing a charging dock against a wall with clearance areas marked.)
Wake up and charge your robot
Turn on the power switch located on the side of the robot's body, then place the robot on the charging dock for a full charge. All lights will turn off when charging is complete.
Tips: For daily use, always keep the robot on the charging dock with power turned on.
(Visual representation: A series of images showing the robot being placed on the charging dock.)
Mopping Mode
- Attach the mop cloth to its bracket, then secure the bracket to the bottom of the robot.
- Fill the clean water cup with water, and carefully pour it into the tank. Close the cap securely.
- Insert the water tank into the robot. Press the 'CLEAN' button on the robot or the 'power' button on the remote control to begin mopping.
(Visual representation: A series of images demonstrating the steps: attaching mop cloth, filling water tank, and inserting tank into robot.)
Robot Maintenance
- For optimal cleaning performance, empty the dustbin and clean the high-performance filter after each use. Note: The high-performance filter cannot be washed with water and should be replaced when needed.
- In homes with pets that shed heavily, the dustbin may fill quickly with fur or hair. In such cases, the dustbin and filters may need to be emptied and cleaned more frequently.
(Visual representation: A series of images showing how to remove and clean the dustbin and filter.)
V5s Pro is ready to clean
Switch on the robot
- Ensure the power switch is on.
- Press the 'CLEAN' button on the robot or the 'power' button on the remote control to start cleaning.
To switch from sleep mode to select mode, press 'CLEAN'. Press 'CLEAN' again to start cleaning.
Pause
To pause the robot and switch from cleaning mode to select mode:
- Press the 'CLEAN' button on the robot.
- Press the 'power' button on the remote control.
Sleep
To put the robot into sleep mode from selected mode:
- Keep pressing the 'CLEAN' button on the main body for 3 seconds.
- The robot enters sleep mode if it does not receive any commands within 15 seconds.
Scheduling
Setting local time
- Point the remote control towards the robot. (Ensure the power switch is on.)
- Press the 'clock' button and then use the directional buttons to set the correct time.
- Press the 'save' button to save the setting. To cancel the schedule, turn off the robot.
Setting a schedule
Once a schedule is confirmed, the robot will automatically start cleaning at the same time every day. If the robot is turned off, you will need to reschedule.
- Point the remote control towards the robot.
- Press the 'schedule' button and then use the directional buttons to set the scheduled time.
- Press the 'save' button to save the setting. To cancel the schedule, turn off the robot.
Trouble Shooting
Error code sheet
When the robot encounters routine problems, it will alert you with beeps.
- Short tone
NO. Tone Cause Solution 01 • Wheels or side brushes disfunction Check wheels or side brushes 02 .. Cliff sensor or bumper sensor failure Clean cliff sensor and shake bumper slightly; check for foreign matter 03 ... Main body gets stuck Move main body and start again Note: If the above solutions do not resolve the issue, please take the following actions:
- Reset the robot by turning the power switch off and then on again.
- If resetting does not work, contact support@iliferobot.com.
