Instructions and Warnings
READ FOLLOWING INSTRUCTIONS AND WARNINGS BEFORE USE
PLEASE FULLY CHARGE THE BATTERY ONCE AT LEAST EVERY 6 MONTHS IN ORDER TO ENSURE NORMAL PRODUCT USE.
Diagram Description: The pump unit is depicted with an inflation port and a deflation port. Three nozzles of varying sizes are attached to the inflation port. A universal USB cable is connected to the pump.
1 IMPORTANT
- This pump is designed for inflating and deflating items such as inflatable air beds and air mattresses.
- It can also be used to charge emergency mobile devices, like mobile phones.
- Keep the air pump out of reach of children.
- Ensure the inflation/deflation ports are never obstructed and remain ventilated at all times.
- For quicker inflation and reduced motor working time, always use the nozzle that best fits the valve size of the inflatable item.
2 WARNING
- To minimize risk, contact a qualified electrician for immediate repair or replacement of damaged cords.
- Follow the inflatable item's instructions carefully during inflation. Do not exceed the recommended pressure, as this could lead to serious injury from bursting.
- Never leave the pump unattended during operation.
- Avoid using or storing the pump in wet conditions.
- Prevent sand, small rocks, or other debris from being drawn into the inflation/deflation port while the pump is in use.
- Never look into the ports or point them towards your eyes while the pump is operating.
3 TO CHARGE BATTERY
Ensure the USB interface voltage is 5V during charging.
Charging Methods:
- Use the universal USB cable. It can charge in your vehicle or with a USB adapter, such as a mobile phone adapter, power bank, or computer. (Refer to FIG. 1)
- Indicator Lights: The display lamp illuminates during charging. One light indicates 25% charge, two lights indicate 50%, three lights indicate 75%, and four lights indicate 100% charge. (Refer to FIG. 2)
- Charging Other Devices: To charge other mobile devices, such as phones, connect the device's USB cable to the pump's USB port and the other end to the mobile device.
- The charging time is approximately 4 hours.
Diagram Description (FIG. 1): Illustrates various USB charging sources (e.g., mobile phone adapter, car cigarette lighter adapter, power bank, computer) connecting to the pump's INPUT port.
Diagram Description (FIG. 2): Depicts the pump's control panel, showing indicator lights labeled 'SPIA LUMINOSA' (Indicator Light) and ports labeled 'INGRESSO' (Input) and 'USCITA' (Output).
4 TO INFLATE ITEMS
- Use the pump directly after the battery has been fully charged.
- Connect the nozzle to the inflation port. Position the pump against the inflatable item's valve and switch it ON to inflate, or OFF to stop. (The switch symbol "-" indicates "ON", and "O" indicates "OFF"). (Refer to FIG. 3)
- The inflatable item's valve must not be obstructed. Failure to do so may cause the pump to overheat and become damaged.
- For large items like inflatable boats or king-size air mattresses, connect the pump directly to the item's valve for rapid inflation. Use the appropriate nozzle for smaller valves, such as those on single-size air mattresses.
Diagram Description (FIG. 3): Shows the pump with a nozzle attached to the inflation port, connected to an inflatable item's valve for the inflation process.
5 TO DEFLATE ITEMS
- Open the valve of the inflatable item.
- Connect the nozzle to the deflation port, insert it into the valve, and switch it ON to deflate. Switch it OFF to stop. (The switch symbol "-" indicates "ON", and "O" indicates "OFF"). (Refer to FIG. 4)
- The inflatable item's valve must not be obstructed. This could lead to overheating and damage to the pump.
- For small valves on inflatable items, you may need to gently pinch the valve flap with your fingers to allow air to escape.
- For rapid inflation of items with screw valves, unscrew the safety bolt first, then inflate directly with the pump.
Diagram Description (FIG. 4): Illustrates the pump with a nozzle attached to the deflation port, connected to an inflatable item's valve for the deflation process.
6 CAUTION
WHEN THE PUMP IS CHARGING A MOBILE PHONE, USE THE ORIGINAL CHARGING CABLE (ANDROID OR APPLE). FIRST, CONNECT THE CHARGING CABLE TO THE PUMP'S USB PORT, THEN CONNECT THE OTHER END OF THE CABLE TO THE MOBILE PHONE PORT. THE PUMP WILL BEGIN CHARGING THE PHONE, AND THE LED LIGHTS WILL ILLUMINATE SIMULTANEOUSLY.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Declarations of Conformity
Learn more about the EU Declaration of Conformity. Please click the link below to download: http://files.drmeter.com/m11-1420n-04-uk.pdf
Learn more about the UK Declaration of Conformity. Please click the link below to download: http://files.drmeter.com/ht-420-uk-doc.pdf
