Bosch Dishwasher Quick Reference Guide

Setting up Home Connect

Tip: Connect your appliance to a mobile device to conveniently change all settings via the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

[Illustration: A QR code for downloading and connecting with the Home Connect mobile application.]

Overview of Water Hardness Settings

This section provides an overview of selectable water hardness values. Country-specific units are detailed in the full instruction manual.

Setting the Water Softening System

1. Press the [button].
2. To open basic settings, press and hold [Setup 3 sec.] for 3 seconds. The display will show H:xx, then 'set'.
3. Press the '+' or '-' buttons repeatedly until the desired water hardness is set.
4. To save settings, press and hold [Setup 3 sec.] for 3 seconds.

Adding Special Salt [salt]

To prevent appliance damage, add special salt to the dispenser only just before starting a programme.

1. Unscrew the lid of the special salt dispenser and remove it.
2. On initial start-up: Fill the dispenser completely with water.
3. Add special salt to the dispenser. The water will be displaced. Never add detergent.
4. Replace the lid on the dispenser and turn to close.

[Illustration: Steps for filling the salt dispenser: unscrewing the lid, filling with water (initial start), adding salt, and closing the lid.]

Adding Rinse Aid [rinse aid]

1. Press the catch on the rinse aid dispenser lid and lift it open.
2. Add rinse aid up to the [max] mark.
3. Close the rinse aid dispenser lid. The lid will click into position.

[Illustration: Steps for filling the rinse aid dispenser: opening the lid, filling to the max line, and closing the lid.]

Adding Detergent

1. Add detergent to the dry detergent dispenser.
2. Close the lid of the detergent dispenser. The lid will click into position.

[Illustration: Detergent being added to the dispenser and the lid being closed.]

Detergent quantities: 50 ml, 25 ml, 15 ml.

Programmes

Programme data is measured according to European standard EN 60436. Consumption figures vary based on the selected programme and additional functions. Programme runtime may change if the rinse aid system is deactivated or rinse aid needs replenishing.

¹ Suitable programme for running at night: it takes longer, but is extremely quiet.

² Half standard load.

Operating Your Appliance

1. Load the tableware. Ensure only dishwasher-safe items are used. Remove large food remnants. Check that spray arms can rotate freely.
2. Add detergent.
3. Switch on the appliance.
4. Select the programme.
5. Start the programme.
6. Remove the tableware at the end of the programme.
7. To cancel a programme, press and hold the 'Reset' button for approximately 4 seconds. The programme will cancel and end within approximately 1 minute.

[Illustration: Interior view of a dishwasher showing how to load tableware, ensuring spray arms have clearance to rotate.]

Cleaning Filters

1. After each wash, check the filters for residue.
2. Turn the coarse filter [counter-clockwise] and remove the filter system.
3. Pull down the micro filter to remove it.
4. Press the locking catches together and lift the coarse filter out.
5. Clean the filter elements under running water.
6. Re-assemble the filter system.
7. Insert the filter system into the appliance and turn the coarse filter [clockwise], ensuring arrow markings align.

[Illustration: Steps for removing and cleaning the dishwasher filter system, including the coarse and micro filters.]

Cleaning Spray Arms

1. Unscrew the upper spray arm and pull it down to remove.
2. Pull up the lower spray arm to remove it.
3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.
4. Insert the lower spray arm. It will click into position.
5. Insert the upper spray arm and screw it firmly in place.

[Illustration: Diagrams showing the removal of the upper and lower spray arms for cleaning.]

Cleaning Wastewater Pump

1. Disconnect the appliance from the power supply.
2. Remove the filter system.
3. Scoop out any remaining water.
4. Using a spoon, prise off the pump cover and grip it by the crosspiece.
5. Lift the pump cover inwards at an angle and remove it.
6. Remove any food remnants and foreign bodies from the impeller area.
7. Insert the pump cover and press down. It will click into position.
8. Install the filter system.

[Illustration: Steps for accessing and cleaning the wastewater pump, including removing the pump cover.]