Yale Smart Safe Installation Instructions
For the French version, visit US.YaleHome.com/Support
Step 1: Download the Yale Access App
Create an account
Download the Yale Access App from the App Store or Google Play.
If you already use the August App, use the same username and password.
Step 2: Unlock Safe Using Key
Open the door and leave it open until setup is complete.
When the key is used to unlock, it must also be used to lock.
Step 3: Insert Batteries
Open the battery compartment and insert 4 AA batteries. Reinstall the cover.
Step 4: Add Safe to the Yale Access App
Set up Smart Safe
Tap "Set up a device" from the app menu. When asked, scan the Yale QR code on the inside of your safe door.
Once batteries are inserted, you have 10 minutes to complete this step. If your app doesn't find the safe, press and hold the reset button (5 seconds) on the inside of the safe door.
Set up Connect*
Note the serial number located on the back of the Connect device. Plug the Connect device into an INDOOR outlet within 10 feet of the Smart Safe.
For best connectivity, ensure the Connect bridge is in the line of sight of the front of the safe.
*Connect WiFi Bridge included with select models.
Step 5: Create Entry Codes
Once added to the Yale Access App, you can create and delete entry codes or share app access by tapping the Guest icon in the bottom menu.
Step 6: Mount Safe For Added Security (Optional)
There are 8 mounting hole locations on the Smart Safe. Use the included mounting template for guidance to secure the safe to the wall, shelf, or floor.
Tips:
- Use a Phillips #2 screwdriver to tighten screws.
- To avoid scratching or damaging your floor, attach the included 4 rubber feet to the bottom of the safe with the 3M side against the safe.
Using Your Smart Safe
Outside View
Note: Safe can always be opened with the key or with a 9V battery and valid code.
9 Volt Battery Back-up: Use an alkaline battery. Hold the battery to the terminals to quickly recharge.
Inside View
Note: When the safe is paired to the app, the Factory Reset must be done from the app. During a factory reset, the safe will be unlocked.
Locking Safe
Close Safe Door. Press any key to lock the safe.
Unlocking Safe
Enter valid 4-6 digit code. Press ✓.
Settings Definitions
| Setting | Default | Definition |
|---|---|---|
| Privacy Mode | Off | While in Privacy Mode, the safe will not open even when a valid Entry Code is entered. This setting can be changed from the Yale Access App. |
| Inside Light | On | The inside light will automatically turn on and stay on for 10 seconds when the safe door is opened. This feature cannot be turned off. |
| One Touch Locking | On | Touching any key on the keypad will lock the safe. This setting cannot be turned off. |
| Sound | On | The sound setting for entry code verification can be set from the Yale Access App. |
Regulatory Information
Warning: Changes or modifications to this device not expressly approved by Yale Home could void the user's authority to operate the equipment.
FCC ID: 2ABFG-IESD100PGO
FCC Compliance: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.
IC ID: 11626A-IESD100PGO
ISED Compliance: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) L'appareil ne doit pas produire de brouillage; (2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
FCC and IC RF Radiation Exposure Statement: This equipment complies with FCC and IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. RF du FCC et IC d'exposition aux radiations: Cet équipement est conforme à l'exposition de FCC et IC rayonnements RF limites é-tablies pour un environnement non contrôlé. L'antenne pour ce transmetteur ne doit pas être même endroit avec d'autres émetteur sauf conformément à FCC et IC procédures de produits Multi-émetteur.
