Pioneer MVH-S220DAB Digital Media Receiver Quick Start Guide

Introduction

This guide provides essential information for operating your Pioneer MVH-S220DAB digital media receiver. For comprehensive details, please consult the full Operation Manual available on the Pioneer website.

Visit: https://www.pioneer-car.eu/eur/

Before You Start

Thank you for choosing PIONEER. To ensure safe and proper use, read this guide thoroughly, paying special attention to WARNING and CAUTION notices. Keep this guide accessible for future reference.

Product Disposal: This product should not be disposed of with general household waste. It must be collected separately for treatment, recovery, and recycling according to environmental regulations. Consumers in the EU, Switzerland, and Norway can return used electronic products free of charge to designated collection points or retailers. For other regions, contact local authorities for proper disposal methods.

WARNING:

• Installation and servicing should only be performed by qualified personnel. Attempting it yourself can be dangerous and may expose you to electric shock or other hazards.
• Never operate the unit while driving. Always pull over and park your vehicle safely before using the controls.

CAUTION:

• Prevent contact with moisture and liquids to avoid electrical shock, damage, smoke, or overheating.
• Maintain a volume level that allows you to hear external sounds for safety.
• The Pioneer CarStereo-Pass is valid only in Germany.
• This product has been evaluated for moderate and tropical climate conditions per IEC 60065 safety standards.

Troubleshooting: If the unit malfunctions, contact your dealer or an authorized PIONEER Service Station.

Connections

Important Installation Notes:

• Battery Drain Prevention: If your vehicle lacks an ACC (accessory) ignition switch position, ensure the red power wire is connected to a terminal that detects ignition key operation to prevent battery drain.
• Vehicle Compatibility: Use only with vehicles equipped with a 12-volt battery and negative grounding.
• Speaker Requirements:
  • For 4-channel speaker output: Use speakers rated over 50 W (max input power) with 4 Ω to 8 Ω impedance. Do not use 1 Ω to 3 Ω speakers.
  • For 2 Ω subwoofer rear output: Use speakers rated over 70 W (max input power).
• Wiring Precautions:
  • Disconnect the negative battery terminal before installation.
  • Secure all wiring with cable clamps or adhesive tape. Protect wires contacting metal parts with tape.
  • Route cables away from moving parts (e.g., shift lever, seat rails) and hot areas (e.g., heater outlets).
  • Do not route the yellow power cable through the engine compartment hole to the battery.
  • Insulate all disconnected cable connectors.
  • Do not shorten cables.
  • Never cut the power cable insulation to share power with other devices due to limited current capacity.
  • Use the specified fuse rating.
  • Never connect negative speaker cables directly to ground.
  • Never connect negative speaker cables of multiple speakers together.
• Blue/White Cable: This cable controls system remote signals (e.g., external power amplifier, auto-antenna relay). Connect to the appropriate terminal (max. 300mA 12V DC). For glass antennas, connect to the antenna booster power supply. Avoid connecting to power terminals of external amps or auto antennas to prevent battery drain or malfunction.
• Black Cable: This is the chassis ground. Ensure separate grounding for the unit and other equipment, especially high-current devices like power amplifiers, to prevent fire or malfunction.
• DC Symbol: The ⎓ symbol on the product indicates direct current.
• Memory Retention: Function and audio settings (except RCA pre-out settings) are retained when power is disconnected.

Unit Connection Ports:

• DAB Antenna Input: For DAB reception, connect an optional DAB antenna (AN-DAB1).
• Power Cord Input
• Rear Output / Subwoofer Output
• Front Output
• Antenna Input
• Fuse (10 A)
• Wired Remote Input: Compatible with optional hard-wired remote control adapters.

Wiring Guide:

• Power: Yellow wire to constant 12V supply; Red wire to ignition-switched 12V DC. Connect matching colors.
• Ground: Black wire to chassis ground.
• Remote Turn-On (Blue/White): Connect to power amplifier system remote control or auto-antenna relay control terminal (max. 300mA 12V DC). Consult vehicle manual for ISO connector pin assignments (Pin 5 for antenna control).
• Audio Mute (Yellow/Black): Connect to the mute lead of audio equipment. Leave unconnected if not used.
• Speaker Outputs:
  • Front Left: White (+), White/Black (-)
  • Front Right: Gray (+), Gray/Black (-)
  • Rear Left/Subwoofer: Green (+), Green/Black (-)
  • Rear Right/Subwoofer: Violet (+), Violet/Black (-)
• ISO Connector: Connect both parts if the connector is split.

Important Notes:

• Initial menu settings can be changed via [SP-P/O MODE]. The subwoofer output is monaural.
• For a 2 Ω subwoofer, connect it to the Violet/Violet-Black leads. Do not use the Green/Green-Black leads for this.

Optional Amplifier Connection: Connect the system remote control to the unit's blue/white cable. Use RCA cables (sold separately) to connect the amplifier to the unit's front and rear/subwoofer outputs.

Installation

General Installation Precautions:

• Verify all connections and systems before final installation.
• Use only authorized parts to avoid malfunctions.
• Consult your dealer for any necessary drilling or vehicle modifications.
• Avoid installing the unit where it could interfere with vehicle operation or pose a safety risk to passengers during sudden stops.
• Install away from heat sources like heater outlets.
• For optimal performance, install the unit at an angle less than 60°.
• Ensure adequate rear ventilation space and keep cables clear of vents for proper heat dissipation.

DIN Mount Installation:

1. Insert the provided mounting sleeve into the dashboard opening.
2. Secure the sleeve by bending the metal tabs (90°) with a screwdriver.
3. Ensure the unit is firmly installed to prevent operational issues like skipping.

Installation Without Mounting Sleeve:

1. Position the unit so its mounting bracket holes align with dashboard mounting points.
2. Secure with two tapping screws (5 mm × 9 mm, not supplied) on each side.

Removing the Unit:

1. Remove the trim ring. (Detaching the front panel offers easier access. Ensure the notched tab on the trim ring faces downwards when reattaching.)
2. Insert the provided extraction keys into the unit's slots until they click.
3. Pull the unit out of the dashboard.

Basic Operation

Unit Controls:

• M.C. (multi-control) dial: Navigates menus and adjusts settings.
• Detach Button: Releases the front panel.
• AUX Input Jack: 3.5 mm stereo jack for external audio devices.
• Display Window: Shows information and menu options.
• DISP Button: Cycles through display information.
• BAND/ Button: Selects radio bands or returns to the previous screen/list.
• BASS Button: Activates and adjusts bass boost.
• USB Port: Connects USB storage devices and compatible smartphones.
• SRC (Source)/OFF Button: Selects audio sources or powers the unit on/off.

Main Menu Navigation:

1. Press the M.C. dial to access the main menu.
2. Rotate the M.C. dial to select a category (FUNCTION, AUDIO, SYSTEM, ILLUMINATION) and press to confirm.
3. Rotate the M.C. dial to choose specific options within a category and press to confirm.

Common Operations:

• Power On/Off: Press SRC/OFF to turn on; press and hold SRC/OFF to turn off.
• Volume Control: Rotate the M.C. dial.
• Source Selection: Press SRC/OFF repeatedly.
• Display Information: Press DISP repeatedly.
• Return to Previous Screen: Press BAND/.
• Return to Normal Display: Press and hold BAND/.
• Adjust Display Brightness: Press and hold BAND/.
• Bass Boost: Press BASS. The level can be adjusted in [BASS BOOST] settings.

Tuner Operation:

• Receiving Preset Stations: Select [RADIO] via SRC/OFF, choose a band (FM1, FM2, FM3, MW/LW) with BAND/, then press a number button (1-6).
• Best Stations Memory (BSM): After selecting a band, access the main menu (M.C. dial), navigate to [FUNCTION], then [BSM], and confirm.
• Manual Station Storage: While tuned to a station, press and hold a number button (1-6) until it stops flashing to store it.

Setup Menu:

Upon initial power-up after installation, [SET UP :YES] will appear. Press the M.C. dial to enter setup. Navigate options using the M.C. dial and confirm selections. To proceed to the next menu item, confirm the current selection.

• LANGUAGE: Choose the display language ([ENG], [РУС], [TUR]).
• CLOCK SET: Set the clock by adjusting hours and minutes with the M.C. dial.
• FM STEP: Select the FM tuning increment ([100] kHz or [50] kHz).
• DAB ANT PW: Enable ([ON]) or disable ([OFF]) power supply to the DAB antenna.

Once setup is complete, [QUIT :YES] is displayed. Confirm settings by pressing the M.C. dial. The unit will then display [UPDATING LIST].

USB/iPod®/AUX Operation

USB/iPod:

1. Open the USB port cover.
2. Connect your USB device or iPod using a suitable cable.

MTP Connection: Android devices (OS 4.0 and later) can connect via MTP using the provided cable. Note that compatibility may vary based on device, OS version, or file count. For MTP connections, set [ANDROID WIRED] to [MEMORY] in SYSTEM settings.

AUX Input:

1. Insert a 3.5 mm stereo mini plug into the AUX input jack.
2. Select [AUX] as the source using the SRC/OFF button.

Pioneer ARC APP Connectivity

The Pioneer Advanced Remote Control (ARC) app transforms your compatible smartphone into a powerful touchscreen remote. Ensure safe operation by parking your vehicle before using the app.

Connecting an Android Device:

1. Navigate to the SYSTEM menu.
2. Select [ANDROID WIRED], then [APP CONTROL], and set [P.APP AUTO ON] to [ON].
3. Connect the unit to your Android device via USB. The Pioneer ARC APP should launch automatically. (Supports Android 4.1-7.1.2 with AOA 2.0; check device compatibility.)

Connecting an iPhone:

1. Connect your iPhone to the unit via USB.
2. Select any source using SRC/OFF.
3. Press and hold the M.C. dial. The Pioneer ARC APP will launch. If it fails to connect, manually start the app on your iPhone.

Spotify® Playback

(Requires Spotify app installed on iPhone)

Ensure your Spotify app is updated to the latest version. Connect your iPhone to the unit via USB.

1. Select [SPOTIFY] using the SRC/OFF button.
2. Launch the Spotify app on your iPhone and begin playback.

Declaration of Conformity

Pioneer Corporation hereby declares that the radio equipment type MVH-S220DAB complies with Directive 2014/53/EU. The complete EU declaration of conformity text is available at: http://www.pioneer-car.eu/compliance

This declaration is provided in multiple languages, including English, French, Italian, German, Spanish, Portuguese, Dutch, Swedish, Danish, Norwegian, Finnish, Greek, Polish, Czech, Slovak, Slovenian, Croatian, Hungarian, Romanian, Bulgarian, Turkish, Maltese, Russian, Latvian, Lithuanian, and Estonian.