User Manual for Cleiscry models including: COB320-05-WL, 2BKGP-COB320-05-WL, 2BKGPCOB32005WL, COB320-05-WL COB LED Strip Light, COB320-05-WL, COB LED Strip Light, LED Strip Light, Strip Light
Hui zhou shi hao li ke ji you xian gong si COB320-05-WL 2BKGP-COB320-05-WL 2BKGPCOB32005WL cob320 05 wl
English Safety Instructions Read and follow all the safety instructions: a. Rated as IP20 non-waterproof, this product can't be used outdoors or humid environment. b. Use the product with the provided power adapter only. c. Keep the product away from sharp objects or strong corrosive chemicals. d. Do not install the COB LED light strip near any heat sources. e. Do not allow children to install the COB LED strip light alone f. Do not extend the length of the light strip. 01 What's in Box? COB LED Strip: 1 Power Adapter: 1 Controller: 1 RF Remote: 1 Quick Start Guide: 1 Specifications Length: Light Color: Width: Power Supply: 16.4ft 3000K/4000K/6500K 8mm 24V/1.5A, 36W 32.8ft 3000K/4000K/6500K 8mm 24V/2A, 48W How to Install? 1.Perparation. a.Check all the items listed on in the packing list. b.Test the light strip before installation, confirm the controller button and remote work perfectly. 2.Wipe the surface, make sure it's CLEAN and DRY, the adhesive can not stick to fabric, dust wall, rough plastic, frosted glass. 02 3.Peel off the protective film of the adhesive tape, stick the COB led strip and PRESS over it firmly. 4.Turn on the light strip and start to use. Control Box Dimmable ON/OFF Scene Mode Remote ON Scene Mode Brightness± Timer OFF Dimmable Cancel Timer 03 Pair remote to the controller: If I've so many sets of this light strip, how could I make each remote work separately. a: One set doing the pair work, other sets should be unplug the power supply (For example, if you've 3 sets or more of this kit, unplug the power supply of the second set or third set before the first set do the pair work). b: Hold "10%" and "50%"button at the same time for 3s, and then release the button, the light strip will flashing, pair work successful, and then pair the second set and third set. Unpair the remote? a: Hold the "OFF" button until the light strip flashing. Replace Battery Cutting. Cut it in the middle of the brown pads or in the middle of the soldering joint. 04 Trouble Shooting QWhy does the COB led strip not light up after connection? AConfirm the connection is firmly. Q: Why does the COB led strip auto turn on/off or auto flashing? A: Interference from other signals caused this problem, hold "10%" and "50%"button at the same time for 3s, and then release the button, the light strip will flashing, problem solved. Q: Why does the adhesive tape not sticky in winter? A: At low temperatures, the adhesive tape will become not strong enough, spread the light strip, and light up for 30 minutes before installation. How to contact us? Support email: Olaholii@hotmail.com Click "Olaholii" on your order page. Warranty 1 Year Warranty (not included the battery). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The device has evaluated to meet general RF exposure requirement. The device can be used be in portable exposure without restriction. 05 Español Instrucciones De Seguridad Lea y siga todas las instrucciones de seguridad: a. Este producto está clasificado como IP20 no resistente al agua y no se puede utilizar en exteriores ni en entornos húmedos. b. Utilice el producto únicamente con el adaptador de corriente proporcionado. c. Mantenga el producto alejado de objetos afilados o productos químicos corrosivos fuertes. d. No instale la tira de luz LED COB cerca de ninguna fuente de calor. e. No permita que los niños instalen la tira de luz LED COB solos. f. No alargue la longitud de la tira de luz. FCC Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 06Adobe Illustrator 28.6 (Windows) Adobe PDF library 17.00