BORMANN BDS2300 Security Safe

Important Information

• Never keep the emergency override keys inside the safe.
• The safe is considered to be firmly secured only when it is mounted on a load-bearing wall or joist.

Technical Data

Packaging Contents

• Safe
• 2 mounting bolts
• 4 AA batteries
• 2 emergency override keys
• Scratch resistant carpet

Parts

The safe consists of the following parts:

• 1. Locking bolts
• 2. Storage hooks*
• 3. Battery compartment
• 4. Reset button (Note: Not for override keys)
• 5. Master knob
• 6. Emergency override keyhole cover
• 7. Numeric keypad
• 8. (C) (E) Enter buttons

Diagram Description: The diagram shows a front view of the BORMANN BDS2300 safe. On the door, a numeric keypad (7) is visible, along with a master knob (5) and an emergency override keyhole (6) covered by a small flap. Inside the safe, indicated by an open door view, are the battery compartment (3) and a reset button (4). Other labeled parts include locking bolts (1) and storage hooks (2).

Mounting Instructions

The safe can be mounted to any surface using the supplied bolts.

1. Open the safe and locate the pre-drilled holes on the back or bottom of the safe.
2. Drill holes for expansion bolts (or clamping screws) suitable for the mounting surface.
3. Use the expansion bolts (or clamping screws) to secure the safe to a wall.
4. Make sure the safe is mounted securely and then tighten all screws/bolts.

Note:

• Use expansion bolts for mounting on a concrete surface.
• Use clamping screws for mounting on a wooden surface.

Diagram Description: Diagram A illustrates the safe being mounted to a wall. Pre-drilled holes on the back of the safe are aligned with holes drilled into the wall. Bolts are shown passing through the safe and into the wall. Diagram B provides a close-up view of the mounting hardware, showing how expansion bolts are used for concrete walls and clamping screws for wooden surfaces.

Opening the Safe Using the Emergency Override Key

1. Remove the rubber cover on the emergency override keyhole at the front of the safe.
2. Insert the emergency override key into the keyhole and turn the key counterclockwise.
3. Turn the master knob clockwise. Pull the door open.

Diagram Description: A sequence of four images shows the steps: 1. Keyhole with cover removed. 2. Key inserted. 3. Key turned counterclockwise. 4. Master knob turned clockwise and door pulled open.

Setting the User Code

1. Open the safe with the emergency override key.
2. Open the battery compartment and insert the 4 AA batteries. Locate the red reset button on the inside.
3. Press and hold the red reset button until you hear a beep and the yellow light comes on.
4. Input your chosen 3-8 digit code then press the (C) or (E) button. A beep confirms correct entry.
5. Try the code with the door still open to ensure it was accepted.

Note: If the yellow light flashes and the buzzer beeps 3 times, the new code is invalid and the process must be repeated.

Diagram Description: Two images show the safe interior with the battery compartment and reset button, and the keypad with the (C) and (E) buttons highlighted.

Opening the Door (with User Code)

1. Input your 3-8 digit code.
2. Press the (C) or (E) button.
3. Wait until the green light comes on and you hear a beep.
4. Turn the master knob clockwise to open the door.

Note: 3 continuous wrong entries will activate a warning beep for 20 seconds. Use the emergency override key to open the safe and stop the beeping.

Diagram Description: Two images show the keypad with code entry and the master knob being turned to open the door.

Manufacturer Notes

The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice, unless these changes significantly affect the performance and safety of the products. The parts described / illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer's product line with similar features and may not be included in the product you just acquired.

To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.

Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.