Online Support - Advantech
Advantech Co-Creating the Future of the IoT World
User Manual for ADVANTECH models including: PPC-306 EHL 6.5 Inch Fanless Panel PC with Intel Celeron N6210 Processor, PPC-306 EHL, 6.5 Inch Fanless Panel PC with Intel Celeron N6210 Processor, Intel Celeron N6210 Processor, Celeron N6210 Processor, N6210 Processor
File Info : application/pdf, 52 Pages, 7.45MB
DocumentDocumentUser Manual PPC-306 EHL 6.5" Fanless Panel PC with Intel® Celeron® N6210 Processor Copyright The documentation and the software included with this product are copyrighted 2023 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties that may result from its use. Acknowledgments Intel® and Celeron® are trademarks of Intel® Corporation. Microsoft Windows is a registered trademark of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Product Warranty (2 years) Advantech warrants the original purchaser that its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or products that have been subject to misuse, abuse, accident, or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events. Because of Advantech's high quality-control standards and rigorous testing, most customers never need to use our repair service. However, if an Advantech product is defective, it will be repaired or replaced free of charge during the warranty period. For out-of-warranty repairs, customers are billed according to the cost of replacement materials, service time, and freight. Please consult your dealer for more details. If you believe your product is defective, follow the steps outlined below. 1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any on-screen messages displayed when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any relevant information readily available. 3. If your product is diagnosed as defective, obtain a return merchandise authorization (RMA) number from your dealer. This allows us to process your return more quickly. 4. Carefully pack the defective product, a completed Repair and Replacement Order Card, and proof of purchase date (such as a photocopy of your sales receipt) into a shippable container. Products returned without a proof of purchase date are not eligible for warranty service. 5. Write the RMA number on the outside, and ship the package prepaid to your dealer. PPC-306 EHL User Manual Part No. 2001030600 Printed in China ii Edition 1 September 2023 Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from damage resulting from electrostatic discharge (ESD) or electromagnetic interference (EMI) leakage, we strongly recommend using CE-compliant industrial enclosure products. Technical Support and Assistance 1. Visit the Advantech website at http://support.advantech.com to obtain the latest product information. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before calling: Product name and serial number Description of your peripheral attachments Description of your software (operating system, version, application software, etc.) A complete description of the problem The exact wording of any error messages Safety Instructions 1. Read these safety instructions carefully. Veuillez lire attentivement ce manuel d'instructions de sécurité. 2. Retain this startup manual for future reference. Veuillez conserver ce manuel d'instructions pour référence ultérieure. 3. Disconnect the equipment from power outlets before cleaning. Use only a damp cloth for cleaning. Do not use liquid or spray detergents. Débranchez l'appareil de toutes les prises de courant avant le nettoyage. Nettoyez-le uniquement à l'aide d'un chiffon humide. Ne pas utiliser de detergents liquides ou pulvérisateurs. 4. For pluggable equipment, the power outlet socket must be located near the equipment and easily accessible. Pour les appareils enfichables, la prise de courant doit être placée près de l'appareil et facilement accessible. 5. Protect the equipment from humidity. Protégez l'appareil contre l'humidité. 6. Place the equipment on a reliable surface during installation. Dropping or letting the equipment fall may cause damage. Placez l'appareil sur une surface fiable pendant l'installation. L'abandon ou la chute de l'appareil pourrait causer des dommages. 7. The openings on the enclosure are for air convection. Protect the equipment from overheating. Do not cover the openings. Les ouvertures du boîtier sont pour la convection d'air. Protégez l'appareil contre la surchauffe. Ne couvrez pas les ouvertures. 8. Warning: ensure that the voltage of the power source is correct before connecting the equipment to a power outlet. The power outlet socket should have a grounded connection. iii PPC-306 EHL User Manual Assurez-vous que la tension de la source d'alimentation est correcte avant de connecter l'appareil à une prise de courant. La prise de courant doit avoir une bonne connexion mise à la terre. 9. Position the power cord away from high-traffic areas. Do not place anything over the power cord. Placez le cordon d'alimentation à l'écart des zones à fort trafic. Ne placez rien sur le cordon d'alimentation. 10. All cautions and warnings on the equipment should be noted. Attention à toutes les précautions et avertissements indiqués sur l'appareil. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage from transient over-voltage. Si l'appareil n'est pas utilisé pendant une longue période, déconnectez-le de la source d'alimentation pour éviter les dommages causés par une surtension transitoire. 12. Never pour liquid into an opening. This may cause fire or electrical shock. Ne versez jamais de liquide dans une ouverture. Sinon, cela pourrait provoquer un incendie ou un choc électrique. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. N'ouvrez jamais l'appareil. Pour des raisons de sécurité, l'appareil ne doit être ouvert que par un technician qualifié. 14. If one of the following occurs, have the equipment checked by service personnel: Si l'un des cas suivants se produit, demandez aide à un technicien qualifié: The power cord or plug is damaged. Le cordon d'alimentation ou la fiche est endommagé. Liquid has penetrated the equipment. Le liquide a pénétré dans l'appareil. The equipment has been exposed to moisture. L'appareil a été exposé à l'humidité. The equipment is malfunctioning or does not function according to the user manual. L'appareil est défectueux ou ne fonctionne pas conformément aux instructions. The equipment has been dropped or damaged. L'appareil a été abandonné et endommagé. The equipment shows obvious signs of breakage. L'equipement montre des signes évidents des casse. 15. Do not leave the equipment in an environment with a storage temperature of below -20 °C (-4 °F) or above 60 °C (140 °F) as this may cause damage. The equipment should be kept in a controlled environment. L'appareil montre des signes évidents de rupture. Ne laissez pas cet appareil dans un environnement dont la température de stockage est inférieure à -20°C (-4 °F) ou supérieure à 60 °C (140 °F), car cela pourrait causer des dommages. L'appareil doit être surveillé dans l'environnement. 16. CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only with the same or equivalent type as recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. ATTENTION: Il y a danger d'explosion s'il y a rem¬placement incorrect de la pile. Remplacer uniquement avec une pile du même type ou d'un type équivalent recommandé par le constructeur. 17. In accordance with the IEC 704-1:1982 specifications, the sound pressure level at the operator's position should not exceed 70 dB (A). PPC-306 EHL User Manual iv Conformément aux spécifications de l'IEC 704-1:1982, le niveau de pression acoustique à la position de l'opérateur ne dépasse pas 70 dB (A). 18. Power to this equipment should be supplied by a UL-certified power adapter or DC power source with mating connector and an output rating of 12 ~ 24 VDC, 5 ~ 2.5A, and an operating temperature tolerance of 50 °C / 122 °F. For further assistance, contact Advantech. 19. DISCLAIMER: These instructions are provided in accordance with IEC 704-1 standards. Advantech disclaims all responsibility for the accuracy of any statements contained herein. AVERTISSEMENT: Ces instructions sont fournies conformément aux normes IEC 704-1. Advantech decline toute responsabilité quant à la précision de toute déclaration contenue dans le présent document. 20. Do not expose the equipment to direct sunlight, or install the equipment in an environment with direct sunlight, as this may cause damage. Safety Precautions - Static Electricity Follow the simple precautions detailed below to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from the PC chassis before manually handling the device. Do not touch any components on the CPU card or other cards while the equipment is powered on. Disconnect the power before executing any configuration changes. A sudden rush of power after connecting a jumper or installing a card may damage sensitive electronic components. Battery Information Batteries, battery packs, and accumulators should not be disposed of as unsorted household waste. Please use the public collection system to return, recycle, or treat them in compliance with local regulations. v PPC-306 EHL User Manual Manual Conventions Warning! Warnings indicate conditions that, if not observed, can cause personal injury! Caution! Cautions are included to prevent hardware damage and data loss. For example, "Batteries are at risk of exploding if replaced with an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Par exemple, "Si la batterie est remplacée par un modèle inapproprié, il y a un risque d'explosion. Remplacer les produits identiques ou équivalents recommandés par le fabricant. Traitement des piles usagées selon les instructions du fabricant." Note! Notes provide additional information. Revision Date September 2023 Version 1.0 Description/Change Initial PPC-306 EHL User Manual vi Contents Chapter 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 Chapter 2 2.1 2.2 2.3 General Information ............................1 Introduction ............................................................................................... 2 Key Features............................................................................................. 2 Front Panel................................................................................................ 2 Figure 1.1 Front Panel ................................................................. 2 Rear Panel ................................................................................................ 3 Figure 1.2 Rear Panel.................................................................. 3 Panel Bottoms........................................................................................... 3 Figure 1.3 Panel PC Bottom ........................................................ 3 Dimensions ............................................................................................... 4 Figure 1.4 PPC-306 EHL Dimensions ......................................... 4 Specifications ............................................................................................ 5 Table 1.1: Specifications ............................................................. 5 Ordering Information ................................................................................. 6 Table 1.2: Ordering Information................................................... 6 System Installation and Setup ...........7 Quick System Tour.................................................................................... 8 Figure 2.1 Panel PC Front View .................................................. 8 Figure 2.2 Panel PC Rear View................................................... 8 Figure 2.3 Panel PC Bottom with I/O........................................... 9 Installation Procedures.............................................................................. 9 2.2.1 Memory Card Installation ............................................................ 10 Figure 2.4 Retention Screws on the Rear Cover ....................... 10 Figure 2.5 Memory Card Installation.......................................... 10 Figure 2.6 .................................................................................. 10 2.2.2 Install the Wi-Fi Module .............................................................. 11 Figure 2.7 Assemble the Bracket with the Antenna Cable....... 11 Figure 2.8 Assemble the Wi-Fi Card and Thermal Pad ........... 11 Figure 2.9 Assemble the Wi-Fi Antenna .................................. 12 2.2.3 System Power on........................................................................ 12 Mounting the System .............................................................................. 13 2.3.1 Wall Mounting ............................................................................. 13 Figure 2.10 Wall Mount Plate..................................................... 13 Figure 2.11 Rear Panel Screw Locations .................................. 14 Figure 2.12 Mounting the Panel PC on a Wall........................... 14 Figure 2.13 Securing the Panel PC ........................................... 15 2.3.2 Panel Mounting ........................................................................... 15 Figure 2.14 Hook Brackets for Panel Mounting ......................... 15 Figure 2.15 Locations of Hook Brackets .................................... 16 Figure 2.16 Fasten the Hook Bracket ........................................ 16 Figure 2.17 Panel Mount Rear View .......................................... 16 2.3.3 Arm Mounting.............................................................................. 17 Figure 2.18 Arm Mount for the Panel PC................................... 17 2.3.4 Stand Mount................................................................................ 17 Figure 2.19 VESA Mount Screw Holes ...................................... 18 Figure 2.20 Securing the VESA Mount Base............................. 18 Figure 2.21 Securing the VESA Mount Bracket......................... 19 Figure 2.22 Securing the Stand Mount Hinge Cover ................. 19 Figure 2.23 Completed Stand Mount ......................................... 20 2.3.5 Cabinet Installation and Grounding............................................. 20 Figure 2.24 Install the PPC System into the Cabinet................. 20 Figure 2.25 System Wiring Cabinet ........................................... 21 vii PPC-306 EHL User Manual Chapter 3 3.1 3.2 Chapter 4 4.1 4.2 Appendix A A.1 Appendix B Jumper Settings................................ 23 Motherboard Jumpers and Connectors .................................................. 24 Figure 3.1 Motherboard ............................................................. 24 Table 3.1: Motherboard Jumpers and Connectors.................... 24 3.1.1 COM1 Pin 9 Power Select .......................................................... 24 Table 3.2: COM1 Pin 9 Power Selection................................... 24 3.1.2 RTC Selection............................................................................. 25 Table 3.3: RTC Selection .......................................................... 25 3.1.3 ATX/AT Selection ....................................................................... 25 Table 3.4: ATX/AT Selection ..................................................... 25 3.1.4 Touch Power Selection............................................................... 25 Table 3.5: Touch Power Selection ............................................ 25 3.1.5 Power Button Connection ........................................................... 26 Table 3.6: Power button connection.......................................... 26 External COM Ports and Pin Definitions ................................................. 26 Figure 3.2 Location of COM1 and COM2 Ports......................... 26 Table 3.7: External COM Ports and Pin Definitions .................. 26 Software Setup.................................. 27 Installing Drivers ..................................................................................... 28 BIOS Setup Utility ................................................................................... 28 4.2.1 Entering BIOS Setup .................................................................. 28 4.2.2 Advanced BIOS Features Setup................................................. 29 4.2.3 Chipset Configuration ................................................................. 34 4.2.4 Security....................................................................................... 36 4.2.5 Boot ............................................................................................ 37 4.2.6 Save & Exit ................................................................................. 38 BSMI RoHS ........................................ 39 BSMI RoHS............................................................................................. 40 BSMI Series Models.......................... 41 PPC-306 EHL User Manual 1 Chapter 1 General Information This chapter details general information regarding PPC-306 EHL. Introduction Specifications Dimensions 1.1 Introduction Advantech's PPC-306 EHL is an all-in-one light panel PC with a wide format 6.5" TFT LCD screen. It is powered by an Intel® Celeron® N6210 processor, PPC-306 EHL to provide high performance, optimal memory, graphics, and peripheral I/O support in a compact, fanless, embedded system. With a high-durability design, PPC-306 EHL adopts a flat touchscreen with an IP66-rated front panel in a die-cast aluminum alloy enclosure. It is ideal for MES, processing, and general industrial equipment integration. 1.2 Key Features Industrial-grade 6.5" VGA TFT LCD with LED backlight Durable true-flat touchscreen with 5-wire resistive touch control Intel® Celeron® N6210 dual-core, 1.2 GHz, processor Up to 32 GB DDR4 SDRAM Compact, fanless design with IP66-rated front panel Supports expansion via M.2 slot Supports VESA 75 x 75 mounting holes 1.3 Front Panel The PPC-306 EHL front panel is a true-flat color TFT LCD touchscreen with Projected Capacitive Multi-Touch. The front panel is IP66 rated for dust and water tolerance (Figure 1.1). Figure 1.1 Front Panel PPC-306 EHLUser Manual 2 Chapter 1 General Information 1.4 Rear Panel The PPC-306 EHL rear panel features four VESA mount (75 x 75 mm /2.95 x 2.95 in) holes located on its bottom side, as demonstrated below: VESA mount screws: 4 x M4 screws, screw depth: 8 mm (max.) Figure 1.2 Rear Panel 1.5 Panel Bottoms The system's I/O, located on the bottom of the device, (Figures 1.3) are listed below: 1 x Power input connector 1 x Power switch 1 x RS-232 connector (COM1) 1 x RS-232/422/485 connector (COM2) 2 x RJ-45 GbE 2 x USB 3.0 1 x USB 2.0 Figure 1.3 Panel PC Bottom 3 PPC-306 EHL User Manual 1.6 Dimensions Figure 1.4 PPC-306 EHL Dimensions PPC-306 EHLUser Manual 4 Chapter 1 General Information 1.7 Specifications Table 1.1: Specifications LCD Panel Display Type Max. Resolution Brightness Viewing Angle Contrast Backlight Lifetime Touchscreen Type LightTransmission Controller Durability (Touches) Enclosure Processor Memory Storage Network (LAN) I/O Ports Expansion Watchdog Timer OS Support Power Supply Power Consumption OperatingTemperature Storage Temperature Relative Humidity Shock Tolerance Vibration Tolerance Safety and EMC Dimensions Weight 6.5" TFT LCD (with LED backlight) 640 x 480 800 cd/m2 89 (left), 89 (right), 89 (up), 89 (down) 1000 70,000 hr (min.) ELO 5-wire resistive touch 80±5% at 550 nm wavelength USB interface Greater than 35 million touches in one location without failure Aluminum Intel® Celeron® N6210 dual core 1 x SO-DIMM DDR4 3200MHz (max. 32GB) 1 x M.2 slot: M key for storage (SATA only, 2242) 2 x 10/100/1000/2500 Mbps Ethernet (Intel I226-LM) 2 x Serial ports: 1 x RS-232, 1x RS-232/422/485 (Adjustable through BIOS) 1 x USB 2.0, 2 x USB 3.0 1 x M.2 slot : E key for wireless module (Type: 2230) 255 timer levels, set up by software Microsoft® Win10(64-bit) IOT LTSC, Win10, Win11, Linux (Ubuntu), Android 12 12-24Vdc 30W (Burn-in test 8.1 in Windows 10, 64-bit) -10 ~ 50 °C (14 ~ 122 °F) -30 ~ 60 °C (-22 ~ 140 °F) 10 ~ 95% @ 40 °C (non-condensing) Operating 10 G peak acceleration (11 ms duration), follow IEC 60068-2-27 Operating Random Vibration Test; 2Grms @with M.2, follow IEC 60068-2-64 CB, UL, CCC, UKCA, CE, FCC Class B, BSMI, UKCA, VCCI, EN60601-1-2 197.6 x 150.6 x 41 mm (7.8 x 5.9 x 1.6 in) 1.5 kg (3.30 lb) Note! The test conditions for the power consumption values provided above were as follows: Memory: 16 GB DDR4 3200 M.2: 64G OS: Windows 10 (64-bit) Software: Burn-In Test 8.1 5 PPC-306 EHL User Manual 1.8 Ordering Information Table 1.2: Ordering Information Part Number Description Image PPC-306-RN6A Panel PC with Intel® Celeron® J6412 96PSA-A90W19OT-3 Power adapter 100 ~ 240 VDC, 90 W, 19V PPC-WLAN-D2 Wi-Fi module with antenna PPC-ARM-A03 Arm mount VESA standard PPC-174T-WL-MTE Wall mount kit PPC-Stand-A1E Stand kit PPC-306 EHLUser Manual 6 2 Chapter 2 System Installation and Setup Quick System Tour Memory Card Installation M.2 Installation Wireless LAN Card Installation Mounting the System 2.1 Quick System Tour Before setting up the panel PC, take a moment to identify the locations of the device controls, drives, connectors, and ports (as shown in Figure 2.3). When placed upright, the PPC-306 EHL front panel should appear as shown in Figure 2.1. Figure 2.1 Panel PC Front View 1. GND screw 1 Figure 2.2 Panel PC Rear View PPC-306 EHL User Manual 8 Chapter 2 System Installation and Setup AB C D E FG Figure 2.3 Panel PC Bottom with I/O A. USB 2.0 B. 2 x USB 3.0 C. 2 x RJ45 LAN D. COM2 RS232/422/485 E. COM1 RS232 F. DC-In G. Power Switch 2.2 Installation Procedures When installing system hardware, adhere to the following order: 1. Install the memory card. 2. Install M.2 storage. 3. Install peripheral devices. 4. Mount the panel PC. 5. Configure the system. 9 PPC-306 EHL User Manual 2.2.1 Memory Card Installation 1. Remove the 8 screws shown in the circles, then remove the rear cover. Figure 2.4 Retention Screws on the Rear Cover 2. Insert the memory card into the corresponding slot on the main board, then place the thermal pad provided in the accessory box on top of the memory card and CPU. Remember to remove the protective film before using the thermal pad. Figure 2.5 Memory Card Installation PPC-306 EHL User Manual Figure 2.6 10 Chapter 2 System Installation and Setup 2.2.2 Install the Wi-Fi Module 1. Remove the rear cover. 2. Assemble the antenna bracket on the antenna cable. Figure 2.7 Assemble the Bracket with the Antenna Cable 3. Assemble the Wi-Fi card and the thermal pad. Figure 2.8 Assemble the Wi-Fi Card and Thermal Pad 11 PPC-306 EHL User Manual 4. Assemble the rear cover, and install the antenna. Figure 2.9 Assemble the Wi-Fi Antenna 2.2.3 System Power on A 2-pin power connector is included in the accessory box. Connect the power connector to 12-30VDC power lines and plug the power cables into the system power receptor. The DC power source shall comply with ES1 requirements, and the output rating is 12-30VDC, 8-4 A, with a minimum operating temperature of 50 °C. It has to be evaluated according to IEC/UL 60950-1 and/or IEC/UL 62368-1. The terminal block is suitable for 16 AWG min., with a torque value 4.5 lb-in min. Use copper conductors only. It must be installed by a trained and skilled person. PPC-306 EHL User Manual 12 Chapter 2 System Installation and Setup 2.3 Mounting the System Warning! When mounting the panel PC, more than one person should perform the installation to prevent accidental damage to the panel or personal injury. Le comité constate qu'el-nasr mounting, Plus d'une personne installation to prevent the cadre accidental damage to the personal injury. The panel PC supports various mounting options, as listed below: Wall mounting Panel mounting Arm mounting Stand mounting 2.3.1 Wall Mounting To mount the panel PC onto a wall, follow the instructions below (see Figure 2.20 for additional reference). 1. Select the location on the wall for the wall mount plate. 2. Mark the locations of the two plate screw holes on the wall. 3. Drill two pilot holes at the marked locations on the wall. 4. Align the wall mount plate screw holes with the pilot holes. 5. Secure the mount plate to the wall by inserting screws into the two pilot holes and tightening them. Figure 2.10 Wall Mount Plate 13 PPC-306 EHL User Manual 6. Insert four M4 screws into the holes on the panel PC and tighten them to secure the bracket to the rear panel. Figure 2.11 Rear Panel Screw Locations Warning! Ensure that the thread depth of the screws on the rear panel does not exceed 4 mm (0.15 in). Assurez-vous que la profondeur du filetage des vis sur le panneau arrière ne dépasse pas 4 mm. 7. To mount the panel PC on the wall, align the wall mount bracket attached to the panel PC with the wall mount plate on the wall and slide the panel PC downward to hang the bracket on the mount plate. PPC-306 EHL User Manual Figure 2.12 Mounting the Panel PC on a Wall 14 Chapter 2 System Installation and Setup 8. Secure the panel PC in place by tightening the screws into the wall mount bracket. Figure 2.13 Securing the Panel PC 2.3.2 Panel Mounting To mount the flat bezel panel PC onto a panel, follow the steps below. 1. Prepare a panel cutout according to the Panel PC dimensions. Panel cutout dimensions: PPC-306: 189 x 136.5 mm / 7.44 x 5.37 in 2. Insert the panel PC into the cutout. Retrieve the hook brackets and M6 x 21L screws from the accessory box. Veuillez installer le panneau PC dans la découpe. Récupérez les crochets et les vis M6 x 21L de la boîte à accessoires. Figure 2.14 Hook Brackets for Panel Mounting 15 PPC-306 EHL User Manual 3. Insert the hook brackets into the holes following the direction of the arrows shown in Figure 2.25 and hang the panel PC. Figure 2.15 Locations of Hook Brackets 4. Tighten the screws to secure the panel PC in place (Figure 2.26). Figure 2.16 Fasten the Hook Bracket Figure 2.17 Panel Mount Rear View (Take the PPC-321W drawing as example.) PPC-306 EHL User Manual 16 Chapter 2 System Installation and Setup 2.3.3 Arm Mounting PPC-306 can be mounted on a VESA-compliant arm mount with a 100 mm (3.93 in) interface pad. To affix the panel PC to an arm mount, follow the steps below. 1. Refer to the installation instructions for the mounting arm to correctly mount the arm onto the surface of the base. 2. Align the retention screw holes on the mounting arm interface with VESA holes on the panel PC, and secure the panel PC with the four M4 retention screws. Figure 2.18 Arm Mount for the Panel PC Warning! Ensure that the thread depth of the screws on the rear panel does not exceed 4 mm (0.15 in). 2.3.4 Stand Mount Before assembling the stand mount, check that the product was shipped with the following items: 17 PPC-306 EHL User Manual To mount the panel PC onto the stand, follow the steps below: 1. Use four M4 x 8L screws to affix the VESA bracket to the panel PC. Users can choose a 100 x 100 mm (3.93 x 3.93 in) VESA mount according to their requirements. Figure 2.19 VESA Mount Screw Holes 2. Use the four M4 x 8L screws to secure the base plate to the mount stand. Figure 2.20 Securing the VESA Mount Base PPC-306 EHL User Manual 18 Chapter 2 System Installation and Setup 3. Use four M4 x 6L screws to secure the mount stand to the VESA mount bracket. Figure 2.21 Securing the VESA Mount Bracket 4. Use one M4 x 5L screw to secure the stand mount hinge cover. Figure 2.22 Securing the Stand Mount Hinge Cover 19 PPC-306 EHL User Manual Figure 2.23 Completed Stand Mount 2.3.5 Cabinet Installation and Grounding Follow these instructions to install the PPC system, and pay attention to the ground pin, which should be connected to the earth/ground. The PPC system should give the best performance for optimal EMI immunity, ESD immunity, surge immunity, and system isolation. If the PPC system is embedded in the cabinet, the PPC system's ground, and the cabinet's ground, and the earth/ground should be connected together. 1. Install the PPC system into the cabinet. Figure 2.24 Install the PPC System into the Cabinet Step A: Connect the cabinet to the earth/ground. Step B: Embed the null PPC system into the cabinet without any I/O or power cables. PPC-306 EHL User Manual 20 Chapter 2 System Installation and Setup 2. System wiring. Figure 2.25 System Wiring Cabinet Step A: Connect the cabinet to the earth/ground. Step B: Ensure that all cabinets have been grounded together. Step C: Connect the ground of the power supply to the cabinet. Step D: Connect the ground pin of the PPC system to the cabinet. Step E: Connect the I/O to the controller if needed. Step F: Connect the V+ and V- of the power supply to the PPC system. Note! The wire of the protective earthing conductor shall be green-and-yellow, xx AWG / 0.75 mm2 and connected to the earth of the building. Ensure that the voltage of the power source is correct before connecting the equipment to a power outlet by means of a power cord connected to a socket outlet with an earthing connection. 21 PPC-306 EHL User Manual PPC-306 EHL User Manual 22 3 Chapter 3 Jumper Settings Jumpers and Connectors External COM Ports and Pin Definitions 3.1 Motherboard Jumpers and Connectors The motherboard connectors are shown below (Figure 3.1). The internal peripheral connectors are accessible when the motherboard is outside of the chassis. JP3 CN4 M2E1 P0 JP4 JP5 JCMOS1 CN21 Figure 3.1 Motherboard The internal jumpers and connectors on the motherboard and their pinouts are listed in the table below. Table 3.1: Motherboard Jumpers and Connectors Connector Function CN4 M2E1 JCMOS1 JP3 JP4 JP5 CN21 M.2 M-Key 2242 M.2 E-Key 2230 RTC Select Resistance Touch Power Select Pin 9 power selection (COM 1) ATX/AT Select Power button connection 3.1.1 COM1 Pin 9 Power Select Table 3.2: COM1 Pin 9 Power Selection JP4 Function 1-2pin 2-3pin 4-5pin COM1 RI (Default*) COM1 Pin9 5V COM1 Pin9 12V PPC-306 EHL User Manual 24 Chapter 3 Jumper Settings 3.1.2 RTC Selection Table 3.3: RTC Selection JCMOS1 Function 1-2pin 2-3pin 3-4pin CLR RTC Register Normal (Default*) Clear CMOS 3.1.3 ATX/AT Selection Table 3.4: ATX/AT Selection JP5 Function 2-3pin 1-2pin ATX power (Default*) AT power 3.1.4 Touch Power Selection Table 3.5: Touch Power Selection JP3 Function Open Closed PCT RES Note! The resistive touch model needs a JP3 jumper added. The projected capacitive touch model should have the JP3 jumper removed. 25 PPC-306 EHL User Manual 3.1.5 Power Button Connection Table 3.6: Power button connection CN21 Function Power button Can be used as an external extension cord switch 3.2 External COM Ports and Pin Definitions Figure 3.2 Location of COM1 and COM2 Ports COM1: RS-232 COM1 Pin 9 is set as "RI" by default. This setting can be changed to 5V or 12V output using a jumper. COM2: RS-232/422/485 Note! COM2 does not support a ring function. Table 3.7: External COM Ports and Pin Definitions COM1 Pin RS-232 COM2 RS-232 RS-422 1 DCD DCD TX- 2 RXD RXD TX+ 3 TXD TXD RX+ 4 DTR DTR RX- 5 GND GND GND 6 DSR DSR NC 7 RTS RTS NC 8 CTS CTS NC 9 Ring or 5V/12V output RING NC RS-485 DATADATA+ NC NC GND NC NC NC NC PPC-306 EHL User Manual 26 4 Chapter 4 Software Setup Installing Drivers BIOS Setup Program 4.1 Installing Drivers When you install the system for the first time, please install the corresponding drivers in advance to make sure all the functions run normally. Please select the drivers to be installed based on the OS you use. Please go to the Advantech. 4.2 BIOS Setup Utility 4.2.1 Entering BIOS Setup You can enter BIOS setup utility by pressing "Delete". You should always press "F4" to save the settings you have made and exit the setup utility, otherwise those settings will not be saved in BIOS. PPC-306 EHL User Manual 28 Chapter 4 Software Setup 4.2.2 Advanced BIOS Features Setup 4.2.2.1 CPU Configuration CPU Configuration View CPU model and frequency. 29 PPC-306 EHL User Manual 4.2.2.2 COM2 Mode Selection (RS232/RS422/RS485) 1. Select NCT6126D Super IO Configuration in the Advanced tab. 2. Select Serial Port 2 Configuration option. PPC-306 EHL User Manual 30 Chapter 4 Software Setup 3. Select Serial Port 2 Mode option to set the COM2 operation mode as RS232 RS422, or RS485. 1) Setting RS232 2) Setting RS422 31 PPC-306 EHL User Manual 3) Setting RS485 If COM2 mode is set as RS485, the RS485 Auto Flow control option can be Enabled or Disabled. 4.2.2.3 Hardware Monitor PPC-306 EHL User Manual 32 Chapter 4 Software Setup EC Hardware Monitor This page displays all information about system Temperature/Voltage/Current. 4.2.2.4 USB Configuration 33 PPC-306 EHL User Manual Legacy USB Support Enable/Disable USB Mass Storage Driver Support 4.2.3 Chipset Configuration 4.2.3.1 Wake-on-LAN 1. Select PCH-IO Configuration option in the Chipset tab. PPC-306 EHL User Manual 34 Chapter 4 Software Setup 2. Set the Wake On By option to Enabled. 4.2.3.2 Deep Sleep 1. Select PCH-IO Configuration option in the Chipset tab. 35 PPC-306 EHL User Manual 2. Set the Deep Sleep by option to Enabled/Disabled for ERP 4.2.4 Security Administrator Password Set Administrator Password. PPC-306 EHL User Manual 36 Chapter 4 Software Setup 4.2.5 Boot Setup Prompt Timeout Number of seconds that the firmware will wait before initiating the original default boot selection. A value of 0 indicates that the default boot selection is to be initiated immediately on boot. A value of 65535(0xFFFF) indicates that firmware will wait for user input before booting. This means the default boot selection is not automatically started by the firmware. Bootup NumLock State Select the keyboard NumLock state. Quiet Boot Enables or disables Quiet Boot option. Boot Option #1 Sets the system boot order. 37 PPC-306 EHL User Manual 4.2.6 Save & Exit Save Changes and Exit This item allows users to exit the system setup after saving changes. Discard Changes and Exit This item allows users to exit the system setup without saving changes. Save Changes and Reset This item allows users to reset the system after saving changes. Discard Changes and Reset This item allows users to reset the system without saving changes. Save Changes This item allows users to save any changes to the setup options. Discard Changes This item allows users to discard any changes to the setup options. Restore Defaults This item allows users to restore/load default values for all setup options. Save as User Defaults This item allows users to save all current settings as user defaults. Restore User Defaults This item allows users to restore all setup options to the user default values. PPC-306 EHL User Manual 38 A Appendix ABSMI RoHS A.1 BSMI RoHS PPC-306 EHL series( Equipment name Type designation (Type) Restricted substances and their chemical symbols Unit Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Polybrominated Polybrominated chromium biphenyls diphenyl ethers (Cr+6) (PBB) (PBDE) -- -- ( ) -- ( ) -- ( -- ...) 1." 0.1 wt %" " 0.01 wt %" Note 1. "Exceeding 0.1 wt %" and "exceeding 0.01 wt %" indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. 2." " Note 2. ""indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 3." " Note 3. "-" indicates that the restricted substance corresponds to the exemption. 26 20 1 02-27927818 Manufacturer: ADVANTECH Co., Ltd. Address: No. 1 Alley 20 Lane 26, Ruiguang Rd., Neihu District, Taipei City Telephone: 02-27927818 PPC-306 EHL User Manual 40 B Appendix BBSMI Series Models BSMI Series Models PPC-306 PPC-306-RN6A, PPC-306-RN6B, PPC-306-RN6C, PPC-306-RN6D PPC-306-PN6A, PPC-306-PN6B, PPC-306-PN6C, PPC-306-PN6D PPC-306-RN6AU, PPC-306-RN6BU, PPC-306-PN6AU, PPC-306-PN6BU PPC306RN2301-T, PPC306RN2302-T, PPC306RN2303-T PPC306RN2304-T, PPC306RN2305-T, PPC306RN2306-T PPC306RN2401-T, PPC306RN2402-T, PPC306RN2403-T PPC306RN2404-T, PPC306RN2405-T, PPC306RN2406-T PPC306RN2501-T, PPC306RN2502-T, PPC306RN2503-T PPC306RN2504-T, PPC306RN2505-T, PPC306RN2506-T PPC306RN2601-T, PPC306RN2602-T, PPC306RN2603-T PPC306RN2604-T, PPC306RN2605-T, PPC306RN2606-T PPC306RN2701-T, PPC306RN2702-T, PPC306RN2703-T PPC306RN2704-T, PPC306RN2705-T, PPC306RN2706-T PPC306RN2801-T, PPC306RN2802-T, PPC306RN2803-T PPC306RN2804-T, PPC306RN2805-T, PPC306RN2806-T PPC306RN2901-T, PPC306RN2902-T, PPC306RN2903-T PPC306RN2904-T, PPC306RN2905-T, PPC306RN2906-T PPC-306 EHL User Manual 42 Appendix B BSMI Series Models PPC-306 EHL User Manual 43 www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2023