AnyTone AT-5289 II 10 Meter Amateur Radio User Manual
1. FUNCTIONS & FEATURES
- LCD display with 7 colors and backlight dimming.
- FM, AM modes.
- Frequency Tuning Steps: 1 KHz, 10 KHz, 100 KHz, 1 MHz.
- Flexible menu functions.
- RX and TX NRC Noise Reduction.
- SQ, ASQ Function.
- RF GAIN Adjustment.
- VFO / BAND / Memory Channel Modes.
- Repeater Shift / Offset Frequency Function.
- CTCSS/DCS with RX/TX Split functions.
- SCAN Function.
- NB/ANL Function.
- DUAL-WATCH Function.
- SWR, S/RF meter Function.
- TOT function.
- HI-CUT Function.
- SWR Protection.
- Power Supply Voltage Protection.
- Key-Lock Function.
- BEEP Prompt.
- VOX Function.
- ECHO Function.
- RB Function.
- User Defined (PF) key on microphone.
- Recording function.
- Clock function.
- Alarm function.
- Compression and expansion function.
2. STANDARD ACCESSORIES
The standard accessories include:
- Microphone
- Hanger
- Screws
- Pads
- Adhesive Case Protectors
- Fuse (15A 250V)
3. GETTING ACQUAINTED
3.1 Front Panel
The front panel features the following controls:
| No. | Key | Functions |
|---|---|---|
| 1 | SQ/ASQ | Squelch Control |
| 2 | VOL/OFF | Power On/Off; Volume Control |
| 3 | NRC | Activate / deactivate the NRC function |
| 4 | DIM | Backlight brightness / color control |
| 5 | RFG | RF Gain / HI-CUT Control |
| 6 | MODE | FM, AM Switch Mode; NB, VOX function |
| 7 | ECHO | Activate / deactivate the ECHO/RB function |
| 8 | DW | Turn on Dual watch / SCAN function |
| 9 | FRQ | Switch Band: A-I / VFO mode |
| 10 | SET | Function menu settings / CTCSS/DCS function |
| 11 | EXIT | Clock/Date Display/Back Button; Keypad lock |
| 12 | MEM | Use, Store memory channels |
| 13 | EMG | Emergency Channel |
| 14 | PLAY | Recording playback menu |
| 15 | REC | Recording menu |
| 16 | CH/FUNC | Channel Switch; FUNC key |
3.2 Rear Panel
The rear panel includes:
| No. | Functions |
|---|---|
| 17 | Antenna Jack |
| 18 | External Speaker Jack |
3.3 Microphone
The microphone has the following controls:
- PTT (Push-to-Talk)
- UP / DOWN buttons
- PF (User defined) button
- 6-Pin Connector with pins for: MIC, EXT.AF, PTT, MIC.KEY, GND, +DC.
- Microphone cable.
4. MODIFY MENU
To modify the PF key function:
- Long press the [PF] key on the microphone to enter the function menu.
- Rotate the channel switch or press the [UP/DN] key on the microphone to select the desired PF key function.
- Short press the [PUSH] key to enter the settings, and rotate the channel switch to select the custom [PF] key function.
- Press any other key or wait for 5 seconds to save and exit the settings.
Available PF key functions:
| No. | LCD Display | Function (Short Press) |
|---|---|---|
| 1 | ASQ | ASQ function on/off |
| 2 | NRC | NR function on/off |
| 3 | ECHO | ECHO function on/off |
| 4 | RFG | Quickly enter the RFG function menu |
| 5 | BP | BEEP function on/off |
| 6 | MIC GAIN | Quickly enter the MIC GAIN function menu |
| 7 | VOX | VOX function on/off |
| 8 | NB | NB function on/off |
| 9 | HI-CUT | HI-CUT function on/off |
| 10 | SCAN | Scan function on/off |
| 11 | RB | RB function on/off |
| 12 | CT/DCS | Quickly switch to CT/DCS menu |
| 13 | R.COMP | R. COMP function on/off |
| 14 | DISP | Quickly switch the DISP menu |
| 15 | FM.DEV | Quickly switch 2K/4K frequency offset |
| 16 | VFO | Quickly switch VFO mode (VFO mode is effective) |
| 17 | STEP | Switching frequency step in VFO mode (VFO mode is effective) |
5. BASIC OPERATION
5.1 Power on and off
To power on, rotate the [VOL/OFF] knob clockwise. To power off, rotate the [VOL/OFF] knob counterclockwise until it clicks.
5.2 Volume Adjusting
Rotate the VOL knob to adjust the volume. Clockwise increases volume, counterclockwise decreases it.
5.3 Channel Selection
In channel mode, rotate the channel knob to select channels. Clockwise increases the channel number, counterclockwise decreases it.
5.4 Squelch Adjustment
Short press [SQ/ASQ] to display "SQ". Rotate the [SQ/ASQ] knob to adjust the mute level. Higher values mean deeper mute levels.
5.5 Automatic Noise Reduction Adjustment
Short press [SQ/ASQ] to display "ASQ". Rotate the [SQ/ASQ] knob to adjust the automatic mute level. Higher values mean deeper mute levels.
5.6 [NRC]
- Short press the NRC button to toggle NRC reception function (displays RNR on LCD).
- Press PTT + NRC to toggle NRC emission function (displays TNR on LCD).
- Press and hold NRC to enter NRC function menu for reception and transmission levels (1-5).
5.7 [DIM/COLOR]
- Short press the DIM button to adjust backlight brightness (6 levels).
- Press PUSH + DIM to select backlight color.
5.8 [RFG/HI-CUT]
- Short press RFG to adjust receiving gain using the channel switch or UP/DN buttons. Higher values mean higher attenuation. 'RF MAX' indicates no attenuation. 'RF AU' indicates automatic gain is enabled.
- Press FUNC + RFG to toggle the HI-CUT function.
5.9 [MODE/NB/VOX]
- Short press MODE to switch between AM/FM modulation modes.
- Press FUNC + MODE to toggle the NB function.
- Press PTT + MODE to toggle the VOX function.
5.10 [ECHO/RB]
- Short press ECHO to toggle the ECHO function.
- Press FUNC + ECHO to enter the RB function menu and select the desired RB sound.
5.11 [DW/SCAN]
- Short press DW to toggle the DW function. Select the first channel, then the second channel, and press DW again to start scanning.
- Press FUNC + DW to activate scanning; press any key to exit.
- Long press DW to enter scanning settings: SKIP (add/remove channels), MODE (SQ for quiet scanning, 5S/10S/15S for time scanning), RANGE (set channel/BAND scanning range or VFO frequency range).
5.12 [FRQ/BAND]
- Short press FRQ to switch frequency or channel number display.
- Press FUNC + FRQ to enter BAND switching. Select the desired BAND and press any key to exit.
5.13 [SET/TSQ]
- Short press SET to enter the function menu. Navigate with the channel switch or UP/DN buttons. Press PUSH to enter settings. Press EXIT to save and exit.
- Press FUNC + SET to enter CTCSS/DCS menu settings. Press EXIT to exit.
5.14 [EXIT/LOCK]
- Press EXIT to toggle clock/date/voltage display mode.
- Press FUNC + EXIT to toggle the button lock function (displays "lock button" icon).
5.15 [MEM]
- Short press MEM to enter storage channel mode. Select channel with channel switch or UP/DN buttons. Short press again to exit.
- Long press MEM to save a storage channel. Select desired channel, long press MEM, select channel to save (MEM01-MEM99), and long press MEM again to save.
5.16 [EMG]
Short press [EMG] to access emergency channels:
- Press once for CH9.
- Press twice for CH19.
- Press three times to return to the normal channel.
5.17 [PLAY]
- Short press PLAY to enter the recording playback menu. Select recording list with channel switch or UP/DN buttons. Press REC to play. Press PLAY to stop playback.
- Long press PLAY to enter the launch recording menu.
Recording launch menu options:
- AUTO PLAY: Turn on/off automatic transmission of recording information.
- PLAYLIST: Select recording to transmit. Displays NULL if no recordings.
- TIME: Set automatic transmission recording time (5-minute steps, up to 120 minutes).
5.18 [REC]
- Short press REC to enter the recording menu. Select recording list with channel switch or UP/DN buttons.
- Press REC again, then PTT to start recording. Release PTT to stop. Press PLAY to play the current recording.
- If recording information exists, short press REC prompts DELETE?. Press PUSH to delete.
5.19 Clock Settings
To enter clock settings: In shutdown state, hold SET and power on. Short press PUSH to cycle through year, month, day, hour, minute, second. Rotate channel switch to modify values. Press EXIT to save and exit.
Screen saver settings: POWER OFF menu allows display settings after shutdown. If set to ON, the radio enters screen saver mode when powered off.
5.20 Clock Settings (Alarm)
To enter alarm mode: In shutdown state, hold DIM and power on. Set alarm time, minute, and enable/disable alarm. Set alarm interval. Rotate channel switch to modify values. Press EXIT to save and exit.
Note: If no key is pressed when the alarm rings, it will ring for 30 seconds and stop. If repeat alarm is set, it will ring again after the specified time. Pressing any key during ringing stops the alarm.
6. MENU
Access the menu by short pressing the SET key. Navigate with the channel switch or UP/DN buttons. Press PUSH to enter settings. Press EXIT to save and exit.
| No. | LCD Display | Function Description |
|---|---|---|
| 1 | BP | BEEP function enable/disable. Enabled when black background/white text is displayed. |
| 2 | VOX | VOX function on/off. LEVEL: VOX sensitivity. TIME: VOX Delay Time. |
| 3 | EMG | Set EMG1/EMG2 channels and modes. |
| 4 | RB | RB function setting. Enabled when black background/white text/numbers are displayed. 1-6 groups available. |
| 5 | ECHO | ECHO: Enable/disable ECHO function. VOLT: ECHO volume (01-32 levels). TIME: ECHO delay time (01-32 levels). |
| 6 | PWR | Set transmission output power. SWR: Set standing wave protection (OFF to disable). TOT: TOT function setting (OFF, 1-9 minutes). |
| 7 | DISP | COLOR: Backlight color selection. BRIGHT: Backlight brightness. CONTRAST: LCD contrast adjustment. |
| 8 | MIC | GAIN: Microphone Sensitivity. TYPE: Microphone type selection. |
| 9 | CT/DCS | MODE: CTSS/DCS function on/off. T-CDT: CTCS/DCS coding settings. R-CDT: CTCS/DCS decoding settings. |
| 10 | R.COMP | Expansion function on/off. Enabled when black background/white text is displayed. |
| 11 | SPLIT | SPLIT: Enable/disable transmission frequency offset function. FREQ: Transmission frequency offset setting. |
7. SPECIFICATIONS
GENERAL
| Parameter | Value |
|---|---|
| Frequency Range | 28.000-29.700MHz |
| Frequency Band | A/B/C/D/E/F/G/H/I |
| Channel | 40 channels in each band |
| Frequency Step | 1 KHz, 10 KHz, 100 KHz, 1 MHz |
| Frequency Tolerance | ±5.0 ppm |
| Temperature Range | -20°C ~ +50°C |
| Microphone | With Push-to-Talk / UP / DN / PF and coiled cord |
| Input Voltage | 13.2 V DC |
| Dimensions (in mm) | 169(L) x 159(W) x 48(H) |
| Weight | 1.02 kg |
| Antenna Connector | UHF, SO239 |
TRANSMITTER
| Parameter | Value |
|---|---|
| Power Output | AM: 60W; FM: 50W |
| Drain | 10A (with modulation) |
| Modulation | FM/AM |
| Emitted power in the adj.channel | inferior to 20 uW |
| Modulated signal distortion | inferior to 5 % |
| Frequency Response | AM/FM: 300 to 3000 Hz |
| Output Impedance | 50ohms, unbalanced |
RECEIVER
| Parameter | Value |
|---|---|
| Sensitivity | AM: 1.0 μV for 10 dB (S+N)/N FM: 1.0 μV for 20 dB (S+N)/N (All at greater than 1/2 watt of audio output) |
| Adjacent-Channel Selectivity | AM/FM: 60dB |
| Image Rejection | More than 65dB |
| Intermodulation Rejection | AM/FM: 50dB |
| IF Frequency | 10.695 MHz 1st IF, 455KHz 2nd IF |
| RF Gain Control | 45dB adjustable for optimum signal reception |
| Automatic Gain Control(AGC) | Less than 10dB change in audio output for inputs from 10 to 100,000 microvolt. |
| Squelch | Adjustable; threshold less than 1.0 μV. Automatic Squelch Control (AM/FM) 1.0 μV |
| Audio Output Power | 3 watts into 8 ohms |
| Frequency Response | AM/FM: 300 to 3000 Hz |
| Built-in Speaker | 8 ohms, round. |
| External Speaker(Not Supplied) | 8 ohms; disables internal speaker when connected. |
WARNING STATEMENTS
Operating Environment:
- Temperature: -10°C to 55°C. Operation outside this range may damage the radio.
- Altitude: Can operate under 2000m.
EU Declaration of Conformity:
AnyTone declares that the radio equipment type Mobile Radio complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at: www.xxxyyy.com
RF Exposure Warning Statements:
This equipment complies with radiation exposure limits for an uncontrolled environment. Install and operate with a minimum distance of 215 cm between the radiator and body.
Caution:
To prevent possible hearing damage, do not listen at high volume levels for long periods.
External Antenna:
- Antenna Gain: 0 dBi (Typical), 3 dBi (Max)
- Antenna Impedance: 50 Ohms
FCC Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
If this equipment causes harmful interference to radio or television reception, the user is encouraged to try to correct the interference by:
- Reorienting or relocating the receiving antenna.
- Increasing the separation between the equipment and receiver.
- Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consulting the dealer or an experienced radio/TV technician.
Industry Canada Compliance:
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
External Antenna:
- Maximum Antenna Gain: 3 dBi
- Antenna Impedance: 50 Ohms
RF Exposure Statement:
This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 215 cm between the radiator and your body.
