Gosvor Pivot Cordless Pool Vacuum User Manual
Welcome to Gosvor
Thank you for choosing the Gosvor Pivot Cordless Pool Vacuum. Please take a few moments to read through this user manual to ensure proper operation and maintenance of your device.
Important Precautions
When installing and using this electrical equipment, basic safety precautions should always be followed, including the following:
- Read the manual carefully and use the product according to the instructions. Gosvor will not be held responsible for any loss or injury caused by improper use or care of this device.
- Only use authorized accessories recommended or sold by the manufacturer or approved affiliates.
- Ensure that children do not attempt to access the cleaner while it is operating.
- Only use 36112 adapters for the device.
- If needed, the adapter cord should only be replaced by a qualified electrician.
- Do not turn on the device when it is out of the pool.
- The charging adapter must be connected to a surge protector when charging.
- Do not operate the cleaner when people or animals are in the pool.
- Always clean and wash the filter tray after using the device.
- Turn off the cleaner when performing maintenance on or cleaning the device.
- The cleaner should be stored in a cool and well-ventilated place, away from direct sunlight.
- While charging, the cleaner should be kept in a cool place and not directly covered by cloth or other objects, as this may overheat components in the device.
- Only certified professionals are permitted to disassemble the sealed driving kit of the cleaner.
- Do not operate the device while the pool filter is running.
- The motor's oil sealing contains grease, which may cause a small discharge of grease if the component is damaged.
- The device is only suitable for swimming pools up to 1292 sq.ft (120m²). Using the device on larger pools may reduce the cleaning effectiveness.
- If the cleaner needs to be stored for an extended period of time, it should be charged every three months to maintain battery life between 40%-60%. If the cleaner is not charged for an extended period, the battery voltage may lower to levels that could be dangerous when recharging.
- Do not use or store the cleaner near any heat source.
- Do not pierce, bludgeon, or throw the device, as this may cause irreparable damage.
- Make sure the charging socket is dried before charging.
- Do not bury the charging cable.
- Ensure the device is turned off before attempting to charge the device.
- If this device is damaged, liquid may leak from the battery and should not be touched.
- If the device is damaged, cease operations immediately.
- Do not modify or attempt to replace the battery pack.
SAVE THESE INSTRUCTIONS.
1. Introduction
The Gosvor Pivot is an energy-saving, environmentally friendly Cordless Pool Vacuum. Highly efficient, this device can clean pool walls and floors automatically without replacing the pool water.
Read this user manual carefully before use.
Parts Overview
The Gosvor Pivot consists of several key components. Visually, the device has a top shell and a bottom shell, with a handle for portability. Internally, it houses a pump motor block with a built-in battery, a rotor for propulsion, and various wheels and support brackets for movement. A filter bag collects debris, and a charging port is located on the device for power input. The device also includes a retrieval hook for easy removal from the pool.
| Item | Part Number | Parts Description |
|---|
| 1 | 64001 | Charging Port |
| 2 | 64012 | Top Shell |
| 3 | NC1015 | 2.5" Rotor |
| 4 | 85020 | Pump Motor Block with Built-in Battery |
| 5 | 64030 | Right Roller Support Bracket, No Drive |
| 6 | 64060 | Right Front Wheel, with Sensor |
| 7 | 64051 | Bottom Shell – Black |
| 8 | 64040 | Left Front Wheel, No Sensor |
| 9 | NC1026 | Bottom Lid |
| 10 | 64191 | Left Roller Support Bracket, with Drive Motor |
| 11 | 64100 | Drive Roller Tube |
| 12 | 36112 | 1A Plug-in wall charger |
| 13 | 64080 | Rubber Brush Pad 2 Pcs Set, Black |
| 14 | 64120 | Foam Collar 3 Pcs Set |
| 15 | NC1017 | Filter Bag |
| 16 | 64110 | Retrieval Hook |
2. Specifications
| Property | Value |
|---|
| 1. Model | Gosvor Pivot |
| 2. Rated Working Voltage | 25.9V |
| 3. Power | 90W |
| 4. Battery Life | 100 Minutes |
| 5. Charger Input | 100~240V, 50/60Hz |
| 6. Charger Output | 25V/1A |
| 7. Battery Capacity | 2600mAh x 6 |
| 8. Charging Time | 3 Hours |
| 9. Pool Size | 100m²/1076sq.ft |
| 10. Filter Capacity | 71GPM(267LPM) |
| 11. Filter Density | 180µm |
| 12. Moving Speed | 32.8ft/min (10m/min) |
| 13. Waterproof Grade | IPX8 |
| 14. Pool Water Temperature | 50°F~77°F (10°C~25°C) |
| 15. Pool Water PH Value | 7.0~7.4 |
| 16. Charging Environment Temperature | 41°F~95°F (5°C~35°C) |
| 17. Max Water Depth | 3m (10feet) |
| 18. Product Size | 430(L)x390(W)x220(H) mm |
| 19. Storage Temperature | -4°F~113°F (-20°C~45°C), RH ≤ 75% |
3. Operations
3.1. Getting Started
- Find a working electrical outlet.
- Wipe the charging port with a towel to prevent water from entering the charging port. The charging port is typically located on the device, often covered by a plastic cap.
- Twist off the plastic cap to plug in the charging cord. The charging cord connects to the device's charging port, ensuring a secure connection.
- The charger indicator light will turn red, indicating the device is charging. Allow 3 hours to fully charge your device, at which time the indicator will turn green. The indicator light will turn green when charging is complete.
- Unplug the charger and screw the plastic cap onto the device ensuring a firm fit. The device is now ready for use.
WARNING: Do not operate the device out of the water as it may damage some components.
To start cleaning, locate the power button on the device, typically on the top surface. Press this button to initiate the cleaning cycle.
- At your pool, press the button, and the blue LED indicator will blink for ten seconds. Place your device into the water, and rock it side-to-side to help any air trapped in the body to escape, then fully submerge the device.
- If you need to stop the cleaning process for any reason, you can manually shut the device down by pressing the button for three seconds.
- After your device has completed its cleaning cycle, it will automatically park near your pool's wall. Use the provided hook (Item 16, Retrieval Hook) to retrieve the device from the pool. The hook is designed to securely grasp the device's handle for easy lifting.
3.2. Cleaning the Filter Bag
- Place the device on the ground, top side down. The underside of the device will be facing upwards, revealing the filter bag compartment.
- Press the two red tabs at the front of the device inwards and towards the front. These tabs secure the lid of the filter compartment.
- Press in the two red clips at the rear and lift up the lid. The lid will pivot open, exposing the filter bag.
- Pull the red ribbon near the front marked "PULL TO REMOVE BAG." This ribbon is attached to the filter bag, allowing for easy removal.
- Empty any debris inside the bag. Dispose of the collected debris appropriately.
- Flip the bag inside out and use a hose to spray the bag to remove any lingering debris. In some instances, washing the bag by hand may be necessary for thorough cleaning.
- Hose clean the lid and body of the device. Ensure all parts of the filter compartment are free of debris.
- Return the bag to its original position and return the cleaned filter back into the lid. Ensure the filter bag is properly seated within its compartment.
- Starting with the sides, attach the lid back to the device's body and secure the tabs in reverse order. Ensure the body is properly latched and snugly fits with the base of the device, indicating a secure closure.
3.3. Cleaning the Rotor
To clean the rotor, ensure the device is turned off and out of the water. Access the rotor area, typically by removing the bottom lid or a designated access panel. Carefully remove any hair, string, or debris that may be wrapped around the rotor or obstructing its movement. Rinse the rotor and its housing with clean water if necessary. Reassemble the components once clean.
4. Troubleshooting
This section provides solutions to common issues encountered with the Gosvor Pivot Cordless Pool Vacuum. If the device is not operating as expected, review the following:
- Device not turning on: Ensure the battery is fully charged. Check the charging indicator light during charging.
- Poor cleaning performance: The filter bag may be full or clogged. Clean the filter bag thoroughly as described in section 3.2. Check if the rotor is obstructed by debris (see section 3.3). Ensure the pool size is within the recommended specifications (1292 sq.ft / 120m²).
- Device stops unexpectedly: The battery may be low. Recharge the device. If the device stops frequently, check for obstructions in the rotor or wheels.
- Device not moving correctly: Check if the wheels or drive roller tube are obstructed by debris. Ensure the device is fully submerged and air has been expelled.
- Liquid leaking from device: If the device is damaged and liquid is leaking from the battery, cease operations immediately and do not touch the liquid. Contact Gosvor Customer Service.
For persistent issues not covered here, please contact Gosvor Customer Service for assistance.
5. Warranty
Details regarding the warranty for the Gosvor Pivot Cordless Pool Vacuum are typically provided by the manufacturer. This section would outline the warranty period, coverage, and conditions for service or replacement. Users are advised to retain their proof of purchase for warranty claims. For specific warranty terms and conditions, please refer to the documentation provided at the time of purchase or contact Gosvor Customer Service.
