Battery Installation
- Make sure the piano is switched off.
- Remove the battery compartment cover underneath the device with a cross head screwdriver (not provided).
- Insert 2 x 1.5V AAA size batteries with correct polarity.
- Replace the battery compartment cover and tighten the screws.
Diagram Description: The diagram shows the underside of the dollhouse with a battery compartment. It illustrates two 1.5V AAA batteries being inserted, showing the correct positive (+) and negative (-) polarity. It also indicates the compartment cover and screws.
Battery Warnings:
WARNING: BATTERIES ARE TO BE INSERTED WITH THE CORRECT POLARITY (+ and -). DO NOT MIX DIFFERENT TYPES OF BATTERIES OR NEW AND USED BATTERIES. NON-RECHARGEABLE BATTERIES ARE NOT TO BE RECHARGED. RECHARGEABLE BATTERIES SHOULD BE CHARGED BY AN ADULT. RECHARGEABLE BATTERIES ARE TO BE REMOVED FROM THE TOY BEFORE BEING CHARGED. THE SUPPLY TERMINALS ARE NOT TO BE SHORT-CIRCUITED. REMOVE BATTERIES FROM THE TOY WHEN NOT IN USE FOR EXTENDED TIME OR WHEN BATTERIES BECOME EXHAUSTED. BATTERY INSTALLATION BY AN ADULT IS REQUIRED. DISPOSE OF BATTERIES RESPONSIBLY. DO NOT DISPOSE OF IN FIRE.
WARNING: DISPOSE OF USED BATTERIES IMMEDIATELY. KEEP NEW AND USED BATTERIES AWAY FROM CHILDREN. IF YOU THINK BATTERIES MIGHT HAVE BEEN SWALLOWED OR PLACED INSIDE ANY PART OF THE BODY, SEEK IMMEDIATE MEDICAL ATTENTION.
Assembly Information
CAUTION: ADULT ASSEMBLY AND SUPERVISION REQUIRED.
WARNING: UNASSEMBLED PARTS CONTAIN SCREWS WITH FUNCTIONAL SHARP POINTS. PLEASE KEEP UNASSEMBLED PARTS AWAY FROM SMALL CHILDREN.
CAUTION: PLEASE CHECK CONDITION OF ITEM REGULARLY. AS SCREWS MAY LOOSEN WITH USE OVER TIME. TIGHTEN SCREW FITTINGS IF NECESSARY. STOP USING THIS PRODUCT IF THERE IS ANY LOOSE OR MISSING FASTENERS, JOINTS OR BROKEN PARTS.
WARNING: FOR SAFETY REASONS, REMOVE ALL TAGS, LABELS AND PLASTIC FASTENERS BEFORE GIVING THIS TOY TO YOUR CHILD. THIS IS A TOY, INTENDED FOR ROLE PLAY ONLY.
Made in China.
Read and follow instructions carefully and keep for future reference.
Tool required: Cross screwdriver ? (not included)
Parts List
The following parts are included in the set:
- Part 1x1: Base panel
- Part 2x1: Side panel
- Part 3x1: Side panel
- Part 4x1: Floor panel
- Part 5x1: Floor panel
- Part 6x1: Floor panel
- Part 7x1: Back panel
- Part 8x1: Back panel
- Part 9x1: Back panel
- Part 10x1: Roof panel
- Part 11x1: Roof panel
- Part 12x1: Stair section
- Part 13x1: Stair section
- Part 14x1: Stair section
- Part 15x1: Stair section
- Part 16x1: Stair section
- Part 17x1: Vertical support
- Part 18x1: Vertical support
- Part 19x1: Vertical support
- Part 20x1: Balcony/Railing piece
- Part 21x1: Balcony/Railing piece
- Part 22x1: Balcony/Railing piece
- Part 23x1: Balcony/Railing piece
- Part 24x1: Balcony/Railing piece
- Part 25x1: Balcony/Railing piece
- Part 26x1: Balcony/Railing piece
- Part 27x9: Small dowels/pegs
- Part 28x1: Chimney/Decorative piece
- Part 29x1: Decorative piece
- Part 30x1: Decorative piece
- Part 31x2: Window frame
- Part 32x1: Window frame
- Part 33x1: Window frame
- Part 34x1: Window frame
- Part 35x1: Door frame
- Part 36x2: Door frame
- Part 37x1: Door frame
- Part 38x2: Door frame
- Part 39x1: Door frame
- Part 40x1: Door frame
- Part 41x1: Door frame
- Part 42x1: Door frame
- Part 43x1: Toilet/Bathroom fixture
- Part 44x1: Sink/Bathroom fixture
- Hardware Ax5: Screws
- Hardware Bx14: Screws
- Hardware Cx17: Screws
- Hardware Dx2: Screws
- Hardware Ex2: Screws
- Hardware Fx2: Screws
Assembly Steps
Follow these steps to assemble the wooden dollhouse:
Step 1:
Diagram Description: Shows attaching part 43 (toilet) and part 44 (sink) to the back panel (part 1) and a floor panel (part 3). Fasteners A and C are indicated.
Step 2:
Diagram Description: Shows attaching a vertical support (part 17) to a floor panel (part 4) using fasteners C.
Step 3:
Diagram Description: Shows attaching another vertical support (part 1) to the same floor panel (part 4) using fasteners C. Part 3 is also shown attached.
Step 4:
Diagram Description: Shows attaching floor panel 3 to the vertical supports (parts 1 and 44) using fasteners A.
Step 5:
Diagram Description: Shows attaching a vertical support (part 18) and a floor panel (part 5) to the structure, using fasteners C and B. Part 9 is also shown.
Step 6:
Diagram Description: Shows attaching floor panel 6 to the vertical supports (parts 18 and 9) using fasteners C.
Step 7:
Diagram Description: Shows attaching back panel 8 to the structure using fasteners C.
Step 8:
Diagram Description: Shows attaching vertical support 15 and floor panel 5 to the structure, secured with fasteners C and B. Parts 23 and 21 are also shown in place.
Step 9:
Diagram Description: Continues assembly by adding part 20 (balcony railing) to the structure, using fasteners C and B, along with parts 15, 23, 21, and floor panel 5.
Step 10:
Diagram Description: Shows attaching back panel 9 to the structure using fasteners C and B. Parts 14 and 12 are also shown.
Step 11:
Diagram Description: Shows attaching stair section 12 and 14 to the structure using fasteners B and F. Part 29 is also shown.
Step 12:
Diagram Description: Shows attaching floor panel 7 to the structure using fasteners B. Parts 1 and 29 are also shown.
Step 13:
Diagram Description: Shows attaching stair sections 27 (x9) and 28 (chimney) to the dollhouse structure. This step is labeled "Advance assembly".
Step 14:
Diagram Description: Shows attaching window frames (parts 31, 32, 33, 34) and door frames (parts 35, 36, 37, 38, 39, 40, 41, 42) to the exterior of the dollhouse using fasteners C and D.
Step 15:
Diagram Description: Shows attaching balcony/railing pieces (parts 20, 21, 22, 23, 24, 25, 26) to the upper levels of the dollhouse using fasteners C and D.
Step 16:
Diagram Description: Shows attaching roof panels (parts 10, 11) to the top of the dollhouse structure using fasteners C.
Step 17:
Diagram Description: Shows attaching the curved staircase sections (parts 22, 24, 25, 26) and roof panels (parts 10, 11) to the dollhouse structure. This step is labeled "Advance assembly".
Step 18:
Diagram Description: Shows attaching vertical supports (parts 1, 18, 19) and floor panels (parts 4, 5, 6) to the main structure using fasteners B.
Step 19:
Diagram Description: Shows the dollhouse with the main structure assembled, including the staircase and some exterior elements.
Step 20:
Diagram Description: Shows the fully assembled dollhouse, furnished with miniature furniture (lamp, chair, table, computer, bed, etc.) and decorative elements. The exterior features windows, doors, and balconies.
