DeerValley Sliding Shower Door Installation Instructions

Watch the Installation Video

Scan the QR code below or visit the following URL for a step-by-step installation guide video:

https://youtu.be/daqWIGJM6HM?si=57Tt0XBjGSAX5b-g

TIP: We recommend watching the full video before starting the installation.

Product Overview and Parts List

Product Breakdown Diagram

A visual representation of the sliding shower door components, with parts labeled A through S for identification.

Parts List:

• NO:A (2PC): Glass Fixing Components
• NO:B (1PC): Circular Tube Guide Rail
• NO:C (2PC): Water Blocking Strip
• NO:D (4PC): Pulley
• NO:E (1PC): Left Wall Cover
• NO:F (2PC): H-Shaped Strip
• NO:G (1PC): Handle
• NO:H (1PC): Door Glass
• NO:I (3PC): Screw-A (st 3/16*1 3/16")
• NO:J (1PC): Lower Slider
• NO:K (1PC): Lower Water Stop Bar
• NO:L (2PC): Water Stop Bar Fixing Parts
• NO:M (1PC): Fixed Glass
• NO:N (5PC): Wall Entry Plug (4/16")
• NO:O (1PC): Right Wall Cover
• NO:P (2PC): Screw-B (st 3/16*1 3/16")
• NO:Q (1PC): Fixed Clip
• NO:R (2PC): Wall Entry Plug (5/16")
• NO:S (3PC): Screw-A (st 3/16*1 3/16")

General Information

Delivery Notes

Upon receiving the product, please immediately inspect for any transportation damage, missing parts, or manufacturing defects.

Cleaning and Maintenance

1. For daily cleaning, use common liquid detergent and a soft cloth.
2. For stains, use a clean soft towel with a small amount of neutral soap or toothpaste to gently wipe.
3. To keep the glass surface shiny, use a polishing agent.

Precautions

1. Do not use acidic, alkaline, or sharp tools during cleaning to avoid damaging the glossiness of shower trays, glass, metal materials, and other accessories' surfaces.
2. Avoid using strong detergents containing acetone or ammonia ingredients; when disinfected, avoid using disinfectants containing formic acid and formaldehyde to prevent damage to the product's surface glossiness.
3. Do not allow body or hard objects to come into contact with or impact the glass surface during showering to avoid accidents.
4. Regularly check the usage condition of the product, and if any abnormalities are found, please contact the after-sales service department promptly.

Tool List (Not Included)

• Tape measure
• Spirit level
• Marker pen
• 1/4" drill bit
• Utility knife
• Electric drill
• Hammer
• Screwdriver
• Allen wrench
• Silicone sealant

Installation Steps

Step 1: Positioning and Installing the Wall Fixed Clip

Start by positioning the fixed clip against the wall, aligning the floor/base surface at a distance of 9.84 inches above the center (based on the glass opening), and mark it with a marker pen. Use a 1/4" drill bit to create holes for marking points, with a diameter of 1/4". Insert the wall plug into the drilled holes, ensuring the plug's end is flush with the wall surface. Secure the wall fixed clip using screws. Ensure they are tightened securely to maintain stability.

Step 2: Installation Sequence of Fixed Glass Accessories

This step involves attaching accessories to the fixed glass. It shows the sequence of attaching components like glass fixing components (NO:A), circular tube guide rail (NO:B), left wall cover (NO:E), H-shaped strip (NO:F), and fixed glass (NO:M) to the main shower structure.

Step 3: Installation of the Lower Water Stop Bar

Begin by placing the lower water stop bar on the floor/base surface. Install each fixing part separately at both ends, and mark the positions using a marker pen. Use a 1/4" drill bit to create holes for the marked points, with a diameter of 1/4". Insert wall plugs into the holes, then secure the lower water stop bar with screws (NO:I) and cover them with decorative caps.

Step 4: Installation Sequence of Circular Tube Guide Rails for the Room Body

This step details the installation of the circular tube guide rails (NO:B) and associated components (NO:P, NO:R) onto the shower enclosure structure. It shows the process of attaching the rails and wall entry plugs.

Step 5: Assembly of Door Glass Accessories

This step focuses on assembling accessories onto the door glass. It shows the installation of water blocking strips (NO:C), pulleys (NO:D), H-shaped strip (NO:F), and the handle (NO:G) onto the door glass (NO:H).

Step 6: Hanging Door Glass and Installing Anti-Detachment Pulley

This step illustrates hanging the door glass onto the installed guide rails and installing the second set of pulleys (NO:D). It shows the process of securing the door glass with the pulleys.

Step 7: Debugging the Door Glass

Use a hexagonal wrench to rotate the eccentric circular disc of the pulley. Adjust the upper and lower pulleys to the appropriate balance point (vertical state) and ensure that they are positioned correctly on the circular tube guide rail. This is primarily to prevent improper use and to serve as a means of preventing detachment. The door glass is considered qualified when it is in a vertical state without shaking. [❌] indicates incorrect, [✔️] indicates correct.

Final Check

After installation, confirm that there are no abnormalities, and apply glass glue for waterproofing. Allow 24 hours for curing. [24 hours] [shower] [❌] [✔️]

Limited Warranty Coverage

5 Year Limited Warranty

DeerValley products are warranted against defects in materials or craftsmanship under regular use for five years from delivery. DeerValley will provide replacement parts or, at its option, replace the defective product or part at no charge. This warranty applies only to the original purchaser, and proof of purchase is required. Scratches are not covered.

The manufacturer warrants the product to be free from manufacturing defects for the warranty period. Retain the original invoice as proof of purchase.

DeerValley may, at its option, repair or replace defective parts/products, issue a refund (within 30 days of delivery), or issue a credit towards a new DeerValley product. Shipping/delivery charges may apply.

DeerValley recommends professional installation by a licensed plumber. DeerValley is not responsible for damage or failure due to improper installation, misuse, or failure to hire a licensed professional. Removal or installation costs are not covered.

This warranty excludes damage from accidents, negligence, improper installation, product abuse, misuse, or cleaners containing abrasives, alcohol, or organic solvents.

DeerValley's responsibility is limited to part replacement; labor charges or consequential damages are not covered. This warranty replaces all other expressed or implied warranties.

Responsibilities of Others

The installer or building contractor is responsible for inspecting the unit for defects or damage prior to installation. If a problem is identified, the unit must not be installed. DeerValley is not responsible for failures that could have been prevented by proper inspection.

Damage occurring during transit is the carrier's responsibility. Inspect the unit upon delivery and report any damage immediately to the seller and carrier in writing.

Limitations and Exclusions

The warranty does not cover negligence, misuse, abuse, improper installation, carelessness, accidents, hard water or mineral deposits, exposure to corrosive materials, misapplication, improper maintenance, or alterations. The warranty is void if the product is altered or repaired with unauthorized parts.

DeerValley is not liable for loss of use, inconvenience, or incidental/consequential costs.

Disclaimer

No other warranties or obligations are provided, whether express, implied, or statutory. No dealer or individual is authorized to make warranties on behalf of DeerValley.

Warranty Service

To obtain warranty service, provide:

• A copy of the original invoice
• Date of installation
• Description and pictures of the defect
• Model number or product description

Contact DeerValley Customer Service for assistance.