SimpleSight™ RVS-155W-HD Wireless Backup HD Camera System
Introduction
NOTE! Please read all installation instructions carefully before installing the product. Improper installation will void manufacturer's warranty.
Congratulations on purchasing a Rear View Backup Camera System! This manual will guide you through proper installation and operation.
The Backup Camera System is intended as a supplement to your standard rear view mirror and should not be used as a substitute for safe, proper, or legal driving. It is not a substitute for any other mirror that exists in your vehicle.
In some jurisdictions, it is unlawful to drive a motor vehicle equipped with a TV viewer or screen located forward of the driver's seat or in any location visible to the driver while operating the vehicle.
Safety Information
Please read the entire manual and follow all instructions and warnings carefully. Failure to do so can cause serious damage, injury, or loss of life. Obey all applicable local traffic and motor vehicle regulations.
Usage
- The Rear View Camera System is designed to help the driver safely detect people and/or objects, helping to avoid damage or injury. Proper use by the driver is essential. This system is not a substitute for safe, proper, or legal driving.
- Never back up solely by looking at the monitor. Always check behind and around the vehicle when backing up, as you would without the system. Back up slowly to avoid damage or injury.
- The system is not intended for extensive back-up maneuvers or backing into cross traffic or pedestrian walkways.
- Remember, the area displayed by the Rear View Camera System is limited and does not show the entire panorama behind you.
Installation
- Incorrect installation can cause electric shock or product malfunction.
- Use the product within the specified voltage range to prevent electronic shock or malfunction.
- Clean the monitor with special care.
- Ensure the product is firmly affixed before use.
- If smoke or a burning smell is detected, disconnect the system immediately.
- Cover any power cable touching a metal case with friction tape to prevent short circuits, which can cause fire.
- Be careful with wire positioning during installation to avoid wire damage.
- The system should only be used when the vehicle is in reverse.
- Do not watch movies or operate the monitor while driving, as it may cause accidents.
- Do not install the monitor where it obstructs driver view or an airbag device.
- Dropping the unit may cause mechanical failure.
Contact Information
For questions about this product, contact:
Rear View Safety
1797 Atlantic Avenue
Brooklyn, NY 11233
Tel: 1.800.764.1028
IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before You Begin
Before drilling, check for cables or wiring on the other side of the wall. Clamp wires securely to prevent damage during vehicle use. Keep cables away from hot/moving parts and electrical noisy components.
We recommend a benchmark test before installation to ensure all components are working properly.
Installation Steps
- Choose the monitor and camera locations.
- Install all cables in the vehicle. Drill a 0.8 (20mm) hole if necessary for passing the camera cable through vehicle walls. Install split grommets where applicable.
- Once all cables and wiring are properly routed, perform a system function test by temporarily connecting the system.
System Operation
Warning!
- This monitor is high voltage. Only professionals should open the monitor's case.
- Do not watch video while driving unless you are monitoring the rear view camera display.
Press "POWER ON" to turn the monitor on. Press "MENU" to access the main menu. Use the arrow keys [arrow-up] [arrow-down] to navigate and the "MENU" button to confirm selections. Press "MENU" again to go back a screen.
Instant Pair
- Connect the camera to power.
- Short press "PAIR".
- The system will automatically pair.
- NOTE: Ensure the camera is receiving power when pairing.
Monitor Dimensions
Diagram Description: A front view of the 5-inch monitor. Buttons are labeled: CAMERA SELECTION, MENU/SELECTION BUTTON, POWER ON/OFF. Below the screen are buttons labeled MENU, MIR/NOR, UP ARROW, DOWN ARROW, PAIR. Dimensions shown are 6.1" width and 4.5" height. An antenna is shown extending upwards.
NOTE: The menu on the RVS-155W-HD and RVS-255W-HD use icons.
Connection Options
Diagram Description:
Top: Shows the monitor and camera. The monitor connects to a power source via a cable labeled "FEMALE TO MALE". Power options for the monitor are shown: "HARDWIRE" or "CIGARETTE LIGHTER PLUG", both connected to a "LOOSE POWER CABLE". The camera connects via its own "LOOSE POWER CABLE".
Bottom: Illustrates "WATERPROOF CONNECTION" in three steps: 1. "PUT IN", 2. "TWIST & TIGHTEN", 3. "WATERPROOF". It shows male and female plugs being connected.
Camera Dimensions
Diagram Description: Shows the camera from multiple angles (front, side, rear) with dimensions. The rear view shows mounting holes. A separate diagram displays a mounting bracket with various dimensions, all in millimeters (mm). Key dimensions for the camera body are approximately 1.77" x 0.59" and 2.35" in depth. The overall unit with bracket is approximately 3.46" x 2.8".
Note: Certain models include bracket for a pre-wired Furrion mount.
Monitor Specifications
| Feature | Specification |
|---|---|
| Panel Size | 5" LED Digital Panel |
| Video System | NTSC / PAL Auto Detection |
| Resolution | 800 X 3 (RGB) X 480 |
| Brightness | 650 cd/m² |
| Contrast Ratio | 500:1 |
| Screen Mode | 16:9 |
| Field of View | Top 50°, Bottom 70°, L/R 70° |
| Power Input | DC10-32V |
| Operating Temperature | -20°C ~ +65°C |
| Storage Temperature | -30°C ~ +70°C |
| Transmission Type | Digital Wireless |
| Transmission Range | 100' in open area |
| Auto Pair | Yes |
| Power Consumption | <5W |
| Power Supply | DC 10-36V |
| Overall Dimensions | 5.25" (H) x 7" (L) x 1.5" (D) |
Camera Specifications
| Feature | Specification |
|---|---|
| Image Sensor | 1/3" Color |
| Active Pixels | 1292 x 968V |
| Chief Ray Angle | 9 degrees linear |
| Night Vision Range | About 5M |
| Audio Input | High sensitivity, -36DB microphone |
| Waterproof Level | IP69K |
| Transmission Range | 2.4G Wireless - 100' in open area |
| Power Supply | DC 10-36V |
| Viewing Angle | 120° |
| Amp Draw | 12V/260mA±10% / 3.12W±10% |
| Power Consumption | <5W |
| S/N Ratio | More than 48 Db |
| Electronic Shutter | 1/100,000(s), ON/OFF |
| Video Output | 1Vp-p 75Ω |
| Maximum current | <250mA |
| Working Temperature | -20 to +65 °C |
| Storage Temperature | -30 to +70 °C |
One Year Warranty
Rear View Safety, Inc. warrants this product against material defects for one year from the date of purchase. The company reserves the right to repair or replace defective units at its sole discretion. Rear View Safety, Inc. is not responsible for defects resulting from misuse, improper installation, damage, or mishandling of electronic components. Rear View Safety, Inc. is not responsible for consequential damages of any kind.
Warranty Void If: Defects in materials or workmanship, or damages resulting from repairs or alterations made by others, unauthorized use of nonconforming parts, normal wear and tear, abuse, improper maintenance, neglect, or accident; or damage due to use of the system after partial failure or with improper accessories.
Warranty Performance
During the warranty period, if the Rear View Safety product exhibits a defect in material or workmanship, the defect will be repaired when the complete product is returned, postage prepaid and insured, to Rear View Safety, Inc. No charge will be made for repairs covered by this warranty, excluding postage and insurance costs.
Warranty Disclaimers
No other warranty, oral or written, expressed or implied, is made. Rear View Safety, Inc. disclaims any implied warranty of merchantability or fitness for a particular use or purpose, and all other warranties. In no event shall Rear View Safety, Inc. be liable for any incidental, special, consequential, or punitive damages, or for any costs, attorney fees, expenses, losses, or delays alleged to be a consequence of any damage to, failure of, or defect in any product, including claims for loss of profits.
Disclaimer
Rear View Safety and/or its affiliates do not guarantee that users will not be involved in an accident or collide with objects or persons. The systems are not a substitute for careful and cautious driving or for adherence to applicable traffic laws and motor vehicle safety regulations. The Rear View Safety products are not a substitute for rearview mirrors or other legally mandated motor vehicle equipment. Camera systems have a limited field of vision and do not provide a comprehensive view of the rear or side area of the vehicle. Always look around your vehicle and use your mirrors to confirm rearward clearance and safe maneuvering. Rear View Safety and/or its affiliates shall have no responsibility or liability for damage and/or injury resulting from accidents occurring with vehicles having these products installed. The manufacturer, distributor, and seller shall not be liable for any injury, loss, or damage, incidental or consequential, arising out of the use or intended use of the product. In no event shall Rear View Safety and/or its affiliates have any liability for any losses (whether direct or indirect, in contract, tort, or otherwise) incurred in connection with the systems, including damaged property, personal injury, and/or loss of life. Neither shall Rear View Safety and/or its affiliates have any responsibility for any decision, action, or inaction taken by any person in reliance on Rear View Safety systems, or for any delays, inaccuracies, and/or errors in connection with system functions.
