Velleman VTSS210 Multifunctional SMD Repair Station

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol [recycling symbol] on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

2. Safety Instructions

This device can be used by children aged from 8 years and above, and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.

[manual symbol] Read and understand this manual and all safety signs before using this appliance.

[indoor use symbol] Indoor use only. Keep this device away from rain, moisture, splashing and dripping liquids. Never put objects filled with liquids on top of or close to the device.

[power cord symbol] Always disconnect mains power when the device is not in use or when servicing or maintenance activities are performed. Handle the power cord by the plug only.

Caution! After switching off, leave the power cord plugged in for a few minutes. When you switch off the unit, the automatic cooling function blows cooling air through the heater pipe for a short period. This protects the heater from damage and extends its lifetime. Do not disconnect the mains plug during this cooling process.

Do not crimp the power cord and protect it against damage.

Warning! If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid any hazard.

Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

Plug the power cord into a suitable, earthed mains outlet.

[electrical hazard symbol] Risk of electroshock when opening the cover. Touching live wires can cause life-threatening electroshocks. Do not disassemble or open the housing yourself. Have the device repaired by qualified personnel.

Do not operate the device with wet hands.

[electrical hazard symbol] Never use the device on live electronic circuits. Make sure power to the work piece is cut and capacitors are discharged.

[warning symbol] Do not use near inflammable products or in explosive atmospheres. Heat can cause fire to inflammable products even when they are not in sight. Only use in properly ventilated rooms.

[warning symbol] Incorrect use may cause fire. Do not touch the shafts, tips, or hot air gun as this can cause serious burns. Keep the tips and hot air away from the body, clothes, or other flammable material. Do not aim the hot air gun at the eyes. Use gloves and/or heat-resistant tools to pick up the PCB assembly to prevent burns. Always return the irons and gun to their stands between uses; always let the device cool down after use and before storage.

Place the device on a level, stable, and fire resistant working surface.

[warning symbol] WARNING! - This tool must be placed on its stand when not in use; do not leave the tool unattended when switched on.

[toxic fumes symbol] Do not inhale solder fumes. The vapours that are released during soldering are harmful. Therefore, you shall only use the soldering station in well-ventilated areas or under an exhaust hood (solder fume extractor). Dispose of fume filters and solder residue in accordance with local regulations.

• Use the soldering iron on a heatproof workbench.
• Place the soldering iron in its holder after use.
• Let a hot soldering iron cool down naturally and do not immerse in water.

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

• Protect this device from shocks and abuse. Avoid brute force when operating the device.
• Keep this device away from rain, moisture, splashing and dripping liquids.
• Familiarise yourself with the functions of the device before actually using it.
• All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
• Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
• Nor Velleman nor its dealers can be held responsible for any damage (extraordinary, incidental or indirect) – of any nature (financial, physical...) arising from the possession, use or failure of this product.

4. How to Solder

• File off any dirt, rust or paint on the parts you wish to solder.
• Heat the parts with the soldering iron.
• Apply resin-based solder to the part and melt it with the soldering iron. NOTE: Be sure to apply a solder paste to the part before applying non resin-based solder.
• Wait for the solder to cool and harden before moving the soldered part.
• CAUTION: Handle a heated soldering iron with extreme care as the high temperatures may cause burns.
• The soldering iron may produce smoke at first use due to a dried out heating element. This is normal and should only last for approx. 10 minutes.
• Never file the soldering tip.
• Use a soldering iron stand in order to avoid burns.
• The temperature of the soldering iron will drop if it is used without the tip.
• Let the soldering iron cool after use.
• The mains cable of this device should not be replaced. Discard the device if the power cable has been damaged.
• Cleaning and user maintenance shall not be made by children without supervision.

5. Features

• auto-standby function
• adjustable airflow and temperature to suit your needs
• automatic cooling system and power-off function
• compatible with various types of air nozzles
• fast heat-up
• can also be used as a hot air gun
• brushless motor fan ensures a soft air flow, long lifespan and low noise during operation

6. Overview

Refer to the illustrations on page 2 of this manual.

7. Operating Temperature

The most common soldering alloys used in the electronics industry consist of 60% tin and 40% lead. The operating temperature of this type of solder is detailed below and can vary from manufacturer to manufacturer. However, to meet RoHS requirements, these solders are no longer allowed and are replaced by lead-free solders that require a working temperature which is ± 30°C (54°F) higher.

A good joint is assured if the iron's operating temperature is set within the parameters suitable for the type of solder being used. The solder will flow too slowly if the temperature is too low; if the temperature is too high, the flux in the solder may burn which will give rise to billowing white smoke. In turn, this will result in a dry joint or in permanent damage to the PCB.

8. Operation

1. Switch on the unit. Wait for the unit to warm up and reach the desired temperature.
2. Apply some solder paste onto the SMD. Position the SMD onto the PCB.
3. Preheat the SMD.

9. Cleaning and Maintenance

• Keep the ventilation openings clear, clean and dust-free at all times.
• If the device is running erratically or something unusual occurs during use, immediately switch off the device and unplug from the mains. Inspect the device before using it again. Repair must only be carried out by a qualified technician.
• If the supply cord is damaged, it must be replaced by a qualified technician.
• Wipe with a damp cloth to keep it looking new. Do not use harsh chemicals, cleaning solvents or strong detergents.
• Clean the device and accessories before storing.

Storing

• Store the device, its accessories and this user manual in the original packaging.
• Always store in a cool and dry place.

10. Technical Specifications

Use this device with original accessories only. Velleman nv cannot be held responsible in the event of damage or injury resulting from (incorrect) use of this device. For more info concerning this product and the latest version of this manual, please visit our website www.velleman.eu. The information in this manual is subject to change without prior notice.

© COPYRIGHT NOTICE The copyright to this manual is owned by Velleman nv. All worldwide rights reserved. No part of this manual may be copied, reproduced, translated or reduced to any electronic medium or otherwise without the prior written consent of the copyright holder.