Olafus Smart Wireless Floodlight Camera

Product Overview

The Olafus Smart Wireless Floodlight Camera combines a powerful LED floodlight with a high-definition security camera, offering smart features for home monitoring.

Key Components and Structure:

• Camera Lock Collar
• Reset Button
• USB Interface
• Micro SD Card Slot
• LED Light
• Speaker
• LED Indicator
• Microphone
• Lens
• PIR Motion Detector
• LED Floodlight

Specifications

Camera:

• 3MP Full HD video quality
• 125° Wide viewing angle
• 170° Advanced PIR motion detecting distance up to 32.8ft
• Two-Way Talk with Audio and advanced noise cancellation
• Remote-activated 67db siren (level measured at 16.4ft distance)

Floodlight:

• Model: 3-LBC55M
• Input Voltage: 100-240V~50/60Hz
• Input Current: 0.6A
• Rated Power: 55W
• Luminous Flux: 5500lm
• CCT: 6500K
• CRI: ≥80
• Power Factor: ≥0.9
• L70B50 lifetime: 30000hours
• Beam Angle: 120°

General:

• Luminaire Location: SUITABLE FOR WET LOCATIONS
• Operating Temperature: -20-40°C (-4°F-104°F)
• Internet Requirements: Recommended minimum upload speed of 2 Mbps per device
• Connectivity: 802.11 b/g/n/ac Wi-Fi connection @2.4GHz, 902-928 Mhz Radio
• Storage: Micro SD Card up to 128GB (not included)

Safety Information

WARNING: Risk of electrical shock

• Disconnect power at the fuse or circuit breaker before installing.
• Verify that the supply voltage is correct. Connect fixture to a 100-240V~50/60Hz power source.
• Properly ground fixture.
• Always follow code standards when installing wire connections.
• If you are outside of North America, installation and wiring must be performed by a licensed electrician.

CAUTION: Risk of fire

• Do not install near combustible or flammable surfaces.

NOTICE

• Do not connect this light fixture to a dimmer switch or timer.
• Floodlight Camera must be installed on a wall and on a UL listed junction box.

WARNING: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

DO NOT CONNECT THIS LIGHT FIXTURE TO AN UNGROUNDED ELECTRICAL SYSTEM. ATTACH GROUND FIXTURE WIRE TO EITHER GREEN GROUND SCREW ON MOUNTING PLATE OR THE GROUND WIRE IN THE OUTLET BOX.

Installation Steps

1. SHUT POWER OFF AT THE BREAKER: Turn off power to the work area at the main circuit breaker or fuse box. Consult a licensed electrician if unsure.
2. PREPARATION: Ensure all parts are present. Estimated Assembly Time: 30-60 minutes. Recommended installation height: 2.5m (8.2ft) to 5m (16.4ft).
3. TOOLS REQUIRED (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Silicone Sealant, Eye Protection, Step Ladder.
4. MOUNTING: Attach the mounting bracket using screws. Ensure the EVA gasket is properly sealed with silicone sealant for wet locations.
5. WIRING: Connect wires using wire nuts: House Live (Black) to Fixture Live (Black), House Neutral (White) to Fixture Neutral (White). Connect ground wires.
6. SECURE FIXTURE: Mount the floodlight camera to the junction box. Ensure the raised part of the metal plate engages with the recessed part of the base.
7. RESTORE POWER: Turn power back on at the breaker. The floodlight camera will enter setup mode.

Connection Preparation

• Install the Floodlight Camera within Wi-Fi coverage.
• Ensure your smartphone is connected to your wireless router.
• The camera only supports 2.4GHz Wi-Fi (not 5GHz).
• Supported smartphones: iOS 9.0 or Android 4.4 and above. Tablets, Mac, or Windows computers are not supported.
• Avoid special characters or symbols in Wi-Fi network name and password.

Pairing with "Smart Life" App

1. Download App: Scan the QR code or search "Smart Life" in the App Store or Google Play.
2. Register/Login: Create an account or log in to your existing Smart Life account.
3. Connect Device: Ensure Wi-Fi and Bluetooth are enabled on your smartphone.
4. Add Device: In the app, tap '+' and select "Add Device" > "Camera & Lock" > "Floodlight Camera".
5. Enter Wi-Fi Password: Select your 2.4GHz Wi-Fi network and enter the password.
6. Scan QR Code: Hold the QR code from the app in front of the camera lens (15-20cm distance).
7. Confirmation: The camera will indicate successful scanning with audio cues and LED status changes (red indicator flashing, then blue indicator flashing).
8. Pairing: Press "I hear prompt" on your phone. The camera will connect to the network.
9. Complete: Wait for the device registration (40-60s). The blue LED will turn solid when connected. Tap "Done" to finish.

Camera LED Indicator Status:

• Red indicator always on: System starting up
• Red indicator flashing: Waiting for pairing to network
• Blue indicator flashing: Network pairing
• Blue indicator always on: Camera connecting to network successful

Resetting the Camera: If pairing fails, long-press the reset button for 3-5 seconds until the red indicator flashes and you hear audio cues. Then, repeat the pairing process.

How to Operate the App

• Motion Detection: Enable "Motion Detection" and "PIR" simultaneously. Adjust sensitivity (Low, Medium, High). When enabled, the lamp can be triggered by motion in darkness.
• Notifications: Receive alert notifications and captured photos when motion is detected. You can disable notification pushes if desired.
• Two-Way Talking: Enable "Microphone" and disable the slash on the "Earpiece" in the app settings to activate two-way communication.
• Siren: Manually activate the siren (67db) via the app.
• Light Control: Manually switch the lamp on/off, adjust brightness, and set timers.
• Micro SD Card Recording: Use a Class 10 or higher speed Micro SD card (up to 128GB). Format to FAT32 before first use. Power off the device before inserting/removing the card.
• Playback: Access recorded videos via the "Playback" section, requiring a Micro SD card.
• Sharing: Share device access with family members. Shared users can view monitoring and notifications but cannot change settings.
• Removing Device: Remove the device from your old phone before switching or connecting to a new one. The device can only be connected by one person at a time unless shared.

Connecting with Alexa Show and Google Assistant

Tap the '+' icon in the app, find the desired voice assistant (e.g., Alexa Show, Google Assistant), and follow the on-screen instructions to link your Olafus camera.

FAQ

1. Cannot connect to camera: Reset the camera. If the issue persists, contact customer support with the camera's serial number.
2. Micro SD Card not found: Use reputable brands (Samsung, SanDisk, Kingston) with Class 10 speed. Format the card to FAT32.
3. Floodlight not turning on automatically: Ensure "Motion Detection" and "PIR" are enabled in the app.
4. Siren not turning on automatically: The siren is designed for manual activation to avoid nuisance alarms.
5. Two-way audio not working: Enable "Two-way talk" in Settings > Basic function settings > Talk Mode.
6. No video feed: Ensure the camera is close to the router and the network connection is stable. Avoid thick walls between the camera and router.

For further questions, use the "FAQ & Feedback" section within the app.

Compliance Information

FCC ID: 2AT7E-3-LBC55M

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.