Altronix Home
User Guide for HubSat models including: HubSat4Di, Passive UTP, Transceiver Hub, Hub, HubSat43Di, HubSat42Di
Altronix HUBSAT4DI | UTP Passive Transceiver Hub, 4 Channel,
File Info : application/pdf, 12 Pages, 922.80KB
DocumentDocumentVideo · Data · Power HubSat4Di Series Passive UTP Transceiver Hub with Integral Isolated Camera Power Models Include: HubSat4Di - Four (4) Camera Channels HubSat42Di - HubSat4Di with four (4) HubWayAv Video Balun/Combiners for 24VAC Cameras HubSat43Di - HubSat4Di with four (4) HubWayDv Video Balun/Combiners for 12VDC Cameras Installation Guide Rev. 090209 More than just power.TM Installing Company: _______________ Service Rep. Name: __________________________________ Address: _____________________________________________ Phone #: __________________ Table of Contents: Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Additional Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 3 Installation Instructions HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power . . . . . . . . . . . . . pg. 3 HubSat4Di for use as a Remote Accessory Module with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 4 Alternate 24VAC Fixed Camera Hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 5 HubSat4Di Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 6 HubWayAv, HubWayAv2, HubWayDv Video Balun/Combiners . . . . . . . . . . . . . . . . . . . . . . . . pg. 7 CAT-5 Structured Cable Wiring Color Codes and PIN Configurations . . . . . . . . . . . . . . . . . . . pg. 7 Typical Application Drawings HubSat4Di as a Passive UTP Transceiver Hub with Integral Camera Power. . . . . . . . . . . . . . . . pg. 9 HubSat4Di as a Remote Accessory Module with HubWay UTP Transceiver Hubs. . . . . . . . . . . . pg. 9 Enclosure Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 12 - 2 - HubSat4Di Installation Guide Overview: Altronix HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power transmits UTP video, RS422/RS485 data and power over a single CAT-5 or higher structured cable. Unit provides 4 camera channels in a wall mount enclosure. Video transmission range is up to 750 ft. max. per channel. Units are compatible with AC and/or DC fixed or PTZ cameras when utilizing Altronix HubWayAv or HubWayDv Video Balun/Combiners. In addition, the unit features individually selectable 24VAC or 28VAC electronically isolated PTC protected outputs with surge suppression. Optionally, the HubSat4Di can be used as an accessory module to transmit video from up to 4 cameras over a single CAT-5 or higher structured cable back to the HubWay, HubWayLD or HubWayLDH Passive and Active UTP Transceiver Hubs. In addition, the HubSat4Di provides power to these cameras locally to eliminate the possibility of voltage drop associated with long cable runs. Specifications: Input: · 115VAC, 50/60Hz, 1.25A. Video: · Four (4) channels of quality video over twisted pair up to a distance of 750 ft. per channel. · Four (4) 75 Ohm video outputs. Data: · RS422/RS485 data input. Power: · Individually selectable 24VAC or 28VAC power outputs with OFF position. · Unit provides up to 1A max. per channel not to exceed a total of 4A maximum current. · Individual electronically isolated outputs. Power (cont.): · PTC protected outputs are rated @ 1A per channel. · Surge suppression. Visual Indicators: · Four (4) power LED indicators. Enclosure Dimensions (H x W x D): 8.5" x 7.5" x 3.5" (215.9mm x 190.5mm x 88.9mm). Optional Accessories: · Video Balun/Combiners: - HubWayAv - for use with 24VAC cameras. - HubWayAv2 - for use with 24VAC cameras. - HubWayDv - for use with 12VDC cameras. Additional Models: HubSat42Di · HubSat4Di w/four (4) HubWayAv Video Balun/ Combiners for 24VAC Cameras. HubSat43Di · HubSat4Di w/four (4) HubWayDv Video Balun/ Combiners for 12VDC Cameras. Installation Instructions: WARNING: To reduce the risk of fire or electric shock do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes. HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power. 1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure's upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install two fasteners. Place the enclosure's upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 12). Secure green wire lead to earth ground. 2. Set illuminated master power disconnect circuit breaker to the [OFF] position (Fig. 4a, pg. 8). 3. Connect 115VAC 50/60Hz to the black and white flying leads of open frame transformer. Secure ground wire (Green) to earth ground (Fig. 5, pg. 9). The power LEDs (Green) for Channels 1-4 of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 6) 4. Select 24VAC or 28VAC power output for each of the Channels 1-4 on HubSat4Di (Fig. 4, pg. 8) with the corresponding output voltage switches. Select OFF position when servicing or installing individual cameras (Fig. 1d, pg. 6). 5. Connect the BNC video outputs marked [Video 1-4] on HubSat4Di to the corresponding video inputs on the head end equipment (DVR) (Fig. 1a, pg. 6). 6. Connect terminals marked [+ Data ] on HubSat4Di (polarity must be observed) to the RS422/RS485 output of the head end equipment (DVR) (Fig. 1f, pg. 6). When using fixed cameras disregard this step. HubSat4Di Installation Guide - 3 - 7. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on HubSat4Di (Fig. 1i, pg. 6). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. · For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e. pg. 7). · For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 7). The total cable distance must not exceed 750 ft. for video transmission between the HubSat4Di and each camera. Repeat this step for all other camera channels [PVD2-4]. 8. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). Power LEDs (Green) of the HubSat will illuminate when AC power is present (Fig. 1e, pg. 6) and HubWayAv and HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 7). 9. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 7) before making connections to each camera to ensure proper operation and avoid possible damage. 10. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8). 11. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power inputs of cameras (Figs. 2a-2e, pg. 7). Polarity must be observed. · HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 7). · HubWayDv - Terminals marked [ 12VDC +] (Figs. 2c, 2d, pg. 7). 12. Connect the terminals marked [+ DATA ] of HubWayAv, HubWayAv2v or HubWayDv Video Balun/ Combiners to the data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 7). Polarity must be observed. When using fixed cameras disregard this step. 13. Connect the BNC connector of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the BNC video outputs of cameras (Figs. 2b-2d, pg. 7). 14. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). 15. The power LEDs (Green) of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 6). Note: If any of the power LEDs are not illuminated the cause may be due to the following: a. AC mains fail. b. Illuminated master power disconnect circuit breaker is tripped. c. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 6). d. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs. To reset the PTC: 1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig. 1d, pg. 6). 2. Eliminate the trouble condition (short circuit or overload). 3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 6). HubSat4Di for use as a Remote Accessory Module with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs. After completing steps 1-4 of Installation Instructions for HubSat4Di Passive UTP Transceiver Hub with Integral Isolated Camera Power proceed with the following. 1. For fixed cameras, run a single CAT-5 cable between HubSat4Di and HubWay, HubWayLD or HubWayLDH to allow video transmission of up to four (4) cameras. For PTZs, run two (2) CAT-5 cables between HubSat4Di and HubWay, HubWayLD or HubWayLDH (Fig. 6, pg. 9). a. Connect one (1) of the CAT-5 cables to the RJ45 jack marked [Video 1-4] on HubSat4Di. Connect the opposite end of this CAT-5 cable into the RJ45 jack marked [CH 1-4] of HubWay, HubWayLD or HubWayLDH unit (Fig. 6, pg. 9). b. For data (PTZ), connect the second CAT-5 cable to the RJ45 jack marked [Data 1-4] on HubSat4Di. Connect the opposite end of this CAT-5 cable into any unused RJ45 jack marked [1-16] of HubWay, HubWayLD or HubWayLDH unit (Fig. 6, pg. 9). Note: Data inputs of HubWay, HubWayLD or HubWayLDH units must be wired in parallel for proper operation. When using fixed cameras disregard this step. - 4 - HubSat4Di Installation Guide 2. Plug the RJ45 connector at one end of the CAT-5 or higher structured cable into the RJ45 jack marked [PVD1] on HubSat4Di (Fig. 1i, pg. 6). Plug the RJ45 connector at the opposite end of the CAT-5 or higher structured cable into the RJ45 jack of the Video Balun/Combiner to be installed at camera 1. · For 24VAC cameras use Altronix model HubWayAv/HubWayAv2 Video Balun/Combiner (Figs. 2a, 2b, 2e, pg. 7). · For 12VDC cameras use Altronix model HubWayDv Video Balun/Combiner (Figs. 2c, 2d, pg. 7). The total cable distance must not exceed 750 ft. for video transmission between the HubSat4Di and each camera. Repeat this step for all other camera channels [PVD 2-4]. 3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). Power LEDs (Green) of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 6) and HubWayAv, HubWayDv Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 7). 4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 7) before making connections to each camera to ensure proper operation and avoid possible damage. 5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8). 6. Connect power outputs of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to power inputs of the cameras (Figs. 2a-2e, pg. 7). Polarity must be observed. · HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 7). · HubWayDv/ - Terminals marked [ 12VDC +] (Figs. 2c, 2d, pg. 7). 7. Connect the terminals marked [+ DATA ] of HubWayAv, HubWayAv2 or HubWayDv Video Balun/ Combiners to the data input terminals of cameras for PTZ control (Figs. 2b-2e, pg. 7). Polarity must be observed. When using fixed cameras disregard this step. 8. Connect the BNC connector of HubWayAv, HubWayAv2 or HubWayDv Video Balun/Combiners to the BNC video outputs of cameras (Figs. 2b-2e, pg. 7). 9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). 10. The power LEDs (Green) of the HubSat4Di will illuminate when AC power is present (Fig. 1e, pg. 6). Note: If any of the power LEDs are not illuminated the cause may be due to the following: a. AC mains fail. b. Illuminated master power disconnect circuit breaker is tripped. c. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 6). d. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs. To reset the PTC: 1. Set the voltage output selector switch for that corresponding channel to the OFF position. Switch must remain in the OFF position for approximately 2 minutes in order for the PTC to reset (Fig. 1d, pg. 6). 2. Eliminate the trouble condition (short circuit or overload). 3. Set the voltage output selector switch for either 24VAC or 28VAC (Fig. 1d, pg. 6). Alternate 24VAC Fixed Camera Hookup (Fig. 7a, pg. 9). After completing steps 1-5 of Installation Instructions Remote Accessory Module for use with HubWay, HubWayLD or HubWayLDH UTP Transceiver Hubs proceed with the following. 1. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 4a, pg. 8). 2. Connect one end of the coaxial cable to the BNC connector marked [Video1] on HubSat4Di (Fig. 1a, pg. 6). Connect the opposite end of the coaxial cable to the BNC video output of camera 1 (Fig. 6a, pg. 9). 3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 4a, pg. 8). Measure the output voltage at terminal pair marked [AUX1] on HubSat4Di to ensure proper operation and avoid possible damage (Fig. 1c, pg. 6). 4. Connect the power output terminal pair marked [AUX1] on HubSat4Di to the power inputs of camera 1 (Fig. 1c, pg. 6). Repeat steps 1-3 for each additional camera [AUX2-4]. HubSat4Di Installation Guide - 5 - Fig. 1 - HubSat4Di Circuit Board 1c 1c 1d 1b 28VAC AUX1 AUX2 28VAC 28VAC AUX3 AUX4 28VAC OFF OFF OFF OFF 24VAC VIDEO1 1a 24VAC 24VAC VIDEO2 VIDEO3 24VAC 1e VIDEO4 + DATA - 1f 1i PVD1 PVD2 DATA 1-4 VIDEO 1-4 PVD3 PVD4 1h 1g 1a - BNC Connector: Video in from remote camera video out to DVR. 1b - Output PTCs: Protects each output. 1c - Power Terminals: 24VAC/28VAC power outputs. 1d - Output Voltage Switches: Selects 24VAC/28VAC/OFF for each output. 1e - LED(s) 1-4: Power output indicators. 1f - Data: RS422/RS485 input from head end equipment (DVR) for PTZ control. 1g - Channels 1-4: Single CAT-5 or higher structured cable out to HubWay, HubWayLD or HubWayLDH enables transmission of up to four (4) video signals. Pin out configuration (Fig. 3, pg. 7). 1h - Data: CAT-5 or higher structured cable to data port on HubWay, HubWayLD or HubWayLDH or head end equipment (DVR). 1i - Channels 1-4: CAT-5 or higher structured cable to cameras. Pin out configuration (Fig. 3, pg. 7). - 6 - HubSat4Di Installation Guide HubWayAv, HubWayAv2, HubWayDv Video Balun/Combiners: Altronix Model Number Input Voltage from HubWay Unit Output Voltage to Camera HubWayAv *24VAC/28VAC *24VAC/28VAC HubWayAv2 *24VAC/28VAC *24VAC/28VAC HubWayDv *24VAC/28VAC 12VDC *Based on camera load and structured cable length. Fig. 2 Camera Type *24VAC/28VAC *24VAC/28VAC 12VDC cameras Power LED Green N/A Red Fig. 2a VIDEO HubWayAv VIDEO BALUN/COMBINER CAT5 AC +DATA-- POWER Fig. 2c VIDEO HubWayDv VIDEO BALUN/COMBINER CAT5 +DATA-- -- 12VDC+ * Also Available as: HubWayDvi Video Balun/ Combiner for non-isolated 12VDC cameras Fig. 2b RJ45 Jack Wire Connectors Fig. 2d RJ45 Jack Wire Connectors To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Fig. 2e - HubWayAV2 Cat5 back to HubWay or HubSat Green Power LED AC Power to Camera -- Data to + Camera To BNC Connector of Camera Structured Cable from HubWay8CD or HubWay16CD Power to Camera Data to Camera Red Power LED + 12VDC Power -- to Camera -- Data to + Camera HubWayAv/HubWayAv2 passes AC voltage from pins 4, 5, 7, 8 to terminals marked [AC Power] (Fig. 3, pg. 7). Video from Camera HubWayDv converts AC voltage to DC voltage from pins 4, 5, 7, 8 to terminals marked [ 12VDC +] (Fig. 3, pg. 7). Fig. 3 - CAT-5 Structured Cable Wiring Color Codes and PIN Configurations 1 - White/Orange [VIDEO +] 2 - Orange [VIDEO ] 3 - White/Green [DATA +] 4 - Blue [AC 1] 5 - White/Blue [AC 2] 6 - Green [DATA ] 7 - White/Brown [AC 2] 8 - Brown [AC 1] HubSat4Di Installation Guide - 7 - OFF Green Lead (ground) + DATA - non power-limited OFF Fig. 4 Fig. 4a - Illuminated master power disconnect circuit breaker: · OFF position: circuit breaker tripped Switch not illuminated. · RESET (ON) position Switch illuminated. (ON) 28VAC AUX1 AUX2 28VAC 28VAC AUX3 AUX4 28VAC OFF OFF 24VAC VIDEO1 24VAC 24VAC VIDEO2 VIDEO3 24VAC PVD1 PVD2 DATA 1-4 VIDEO 1-4 PVD3 PVD4 non powerlimited Input 115VAC, 60Hz non power-limited - 8 - HubSat4Di Installation Guide Typical Application Drawing for HubSat4Di Passive UTP Transceiver Hub with Integral Camera Power: Fig. 5 Head End Equipment (DVR) RS485 Monitor Data Data Video Power 12VDC PTZ Camera CAT-5 HubWayDv Video Balun Combiner Video Power CAT-5 BNC CAT-5 HubWayAv Video Balun Combiner Data Video Power 24VAC PTZ Camera CAT-5 Video Power 12VDC Fixed Camera HubWayDv Video Balun Combiner 115VAC Input, 50/60Hz 24VAC/28VAC Camera Power Provided by HubSat4i HubWayAv Video Balun Combiner 24VAC Fixed Camera Typical Application Drawing for HubSat4Di Remote Accessory Module for use with HubWay/HubWayLD/HubWayLDH UTP Transceiver Hubs: Fig. 6 Head End Equipment (DVR) RS485 Data Rear Video Monitor 8 7 6 5 4 3 2 1 PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN PICTURE GAIN AC POWER 1 2 3 4 CH 1-4 5 6 7 8 CH 5-8 + DATA 1-8 28VAC OFF 24VAC Data Video Power Data (CAT-5) CAT-5 Four (4) Video signals on a single CAT-5 CAT-5 Data Video Power Four (4) Video signals on a single CAT-5 Power Video (Coax) Front Power Video (Coax) HubWayDv 12VDC PTZ Video Balun Combiner Camera CAT-5 Video Power HubWayDv 12VDC Fixed Video Balun Combiner Camera HubSat4Di Installation Guide 24VAC/28VAC Camera Power Provided by HubSat4i 115VAC Input, 50/60Hz HubWayAv Video Balun Combiner 24VAC PTZ Camera CAT-5 Video Power HubWayAv Video Balun Combiner 24VAC Fixed Camera 24VAC Fixed Camera Power Video (Coax) 24VAC Fixed Camera 24VAC/28VAC Camera Power Provided by HubSat4i 115VAC Input, 50/60Hz 24VAC Fixed Camera Power Video (Coax) 24VAC Fixed Camera Fig. 6a - Alternate 24VAC fixed camera hookup. - 9 - Notes: - 10 - HubSat4Di Installation Guide Notes: HubSat4Di Installation Guide - 11 - The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product's enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel. Enclosure Dimensions (H x W x D approximate): 8.5" x 7.5" x 3.5" (215.9mm x 190.5mm x 88.9mm) 7.25" (184.2mm) 3.625" (92mm) 1.25" (31.8mm) 3.5" (88.9mm) 1.25" (31.75mm) 0.6" (15.2mm) 1.125" (28.6mm) 6.05" (153.7mm) 0.6" (15.2mm) 1.125" (28.6mm) 8.125" (206.4mm) 2" (50.8mm) 2" (50.8mm) 1" (25.4mm) 0.6" (15.2mm) 6.05" (153.7mm) 1" (25.4mm) 0.6" (15.2mm) 1.25" (31.75mm) 3.5" (88.9mm) 1" (25.4mm) 5.25" (133.35mm) 1" (25.4mm) 1" (25.4mm) Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIHubSat4Di I20U MEMBER - 12 - HubSat4Di Installation Guide