ZEISS Supreme Prime Instruction Manual

Disclaimer

To ensure proper and safe use, it is recommended to read these safety and operating instructions before using the product and store them in a safe place. Non-observance of these instructions could lead to injury or damage.

Carl Zeiss AG reserves the right to change these specifications without prior notice. An updated version of the instruction manuals can be found at www.zeiss.com/cine/manuals.

All rights reserved. This manual, or parts thereof, may not be reproduced without prior written permission from Carl Zeiss AG, stored in retrieval systems, or transmitted in any form, whether electronically, mechanically, by photocopy, recording or other media. Copyright 2018, Carl Zeiss AG.

Technical Data

Versions

The ZEISS Supreme Prime lenses are available with PL mount and can be converted into the following mounts:

• LPL (with electronic interface)

Further technical information on the lenses can be found on: www.zeiss.com/cine/supremeprime

Lens Components

The following diagram illustrates the components of the lens:

1. Front lens element
2. Focus ring
3. Focus index mark
4. External socket (4-pin mechanical connector)
5. Aperture index mark
6. Aperture ring
7. Lens mount
8. Rear lens element

Safety & Handling

Safety Tips

• Never point the lens directly towards the sun, as there is a significant risk of harming your eyesight.
• Always attach the lens cap when the lens is not in use. Otherwise, there is a danger of fire!

Storage & Transportation

Use the product only in temperatures ranging between -20°C and 55°C. Store this product only in temperatures ranging between -40°C and +70°C.

The product is not completely water resistant, dust resistant, or waterproof. Protect the camera and lens appropriately when in the rain and in damp or dusty environments. Should the product be exposed to moisture, remove it from the camera. Allow the device to dry completely before you use it again. Do not attempt to dry the product with the aid of an external heat source, e.g., in a microwave oven or with a hairdryer.

Modification, Service and Repair

You are allowed to perform the following modifications: Changing the mount, changing the external socket, adjusting the flange focal distance, switching the scale ring, and updating the firmware. Please follow the instructions on our website: www.zeiss.com/cine/manuals.

Do not undertake any other unauthorized modifications or repairs on the product yourself. By disassembling it, damage may be caused which is not covered by the warranty. If it needs repair, please contact your authorized dealer and distributor. For this purpose, see www.zeiss.com/cine/service.

European Directive of Regulation

When the product left the factory, it was in a completely safe working condition. It meets the electromagnetic compatibility requirements set out in Directive 2014/30/EU and bears the CE test mark.

Disposal

Do not dispose of the product as household waste but please follow the applicable statutory regulations of the relevant country. Consult local authorities about the options for disposal and recycling if necessary.

Warranty

The product is subject to the statutory warranty of 12 months.

Damage to or problems caused by the unauthorized opening of the product are not covered by the warranty. Before submitting a warranty claim, make sure that the possibility of an operator error has been ruled out. Please refer to the support information in this regard at www.zeiss.com/cine.

Handling

Intended Use

ZEISS Supreme Prime lenses are designed for use on cameras with interchangeable lenses. Usage in any other scenario is not recommended.

Removing the Rear Cap

Remove the rear cap from the lens by turning it counter-clockwise.

Attaching the Rear Cap

Attach the rear cap to the lens by turning it clockwise.

Mounting and Removing the Lens

Please refer to the mounting instructions in the user guide of your camera.

Lens Care Tips

To ensure that your lens is always in perfect condition, avoid any form of dirt or humidity on the glass surface. Dust on the lens can be removed carefully with a soft brush. Stains and fingerprints can be removed with a soft, dry, and clean microfiber cloth. To remove stubborn dirt, ZEISS cleaning fluid is additionally recommended. Please follow the instructions of the ZEISS Lens Cleaning Kits.

Customer Support

Your nearest ZEISS dealer can be found on the homepage www.zeiss.com/cine.