Omada by TP-Link

For technical support, replacement services, user guides, and more, please visit https://support.omadanetworks.com/.

Note: Images may differ from the actual products.

Installing the RJ45 SFP / RJ45 SFP+ Module

1. Lock the yellow latch into place and insert the module into an SFP/SFP+ slot with the label side up.
2. Gently push the module into the slot until you hear a click. Then, insert the RJ45 network cable.

Removing the RJ45 SFP / RJ45 SFP+ Module

1. Press the RJ45 crystal head and pull out the cable.
2. Pull down the latch and remove the module.

Positioning the 10G RJ45 SFP+ Modules

The 10G RJ45 SFP+ modules consume more power than optical modules, which may generate more heat. To avoid overheating, it is recommended to place the modules separated by multiple optical transceivers or empty slots. When used in high temperature environments, additional cooling must be applied.

The figures below only show the recommended positioning. The actual number of modules that can be inserted depends on the switch's heat dissipation and power margin.

Scenario 1:

Recommended: [Module] [Empty Slot] [Module]

Not Recommended: [Module] [Module] [Module]

Scenario 2:

Recommended: [Module] [Empty Slot] [Module]

Not Recommended: [Module] [Module] [Module]

Specifications

General Specifications

Compatibility

We recommend using only Omada modules for your Omada devices. To find the compatible Omada devices for your module, please visit our website.

Notes:

• SM5310-T does not support the data rate of 10 Mbps or 100 Mbps.
• When using a gigabit RJ45 SFP module in a 10G SFP+ slot, additional port speed configuration may be required.
• When a 10G RJ45 SFP+ module operates at 1 Gbps, manual port speed configuration may be required. If inserted into a 10 Gbps SFP+ slot and the peer port supports only 5 Gbps or 2.5 Gbps, flow control must be manually enabled on the 10 Gbps SFP+ slot.

Environmental and Physical Specifications

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact TP-Link.
• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
• This equipment can be powered only by equipments that comply with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.

Declarations of Conformity

EU Declaration of Conformity

TP-Link hereby declares that the SFP module is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce.

UK Declaration of Conformity

TP-Link hereby declares that the SFP module is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016. The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca.

FCC compliance information statement

Product Name: 1000BASE-T RJ45 SFP Module/10GBASE-T RJ45 SFP+ Module

Model Number: SM331T/SM5310-T

Responsible party: TP-Link Systems Inc.

Address: 10 Mauchly, Irvine, CA 92618

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

We, TP-Link Systems Inc., have determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Industry Canada Statement

CAN ICES-003 (A)/NMB-003(A)

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Ukrainian Conformity Statement

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Explanation of the symbols on the product label

Note: The product label can be found at the bottom of the product. Symbols may vary from products.