KSIV REMOTE CONTROLLER OWNER'S MANUAL

Remote Controller Specifications

Quick Start Guide

Follow these steps to get started:

1. FIT BATTERIES: Insert batteries into the remote control.
2. SELECT MODE: Press the MODE button to cycle through AUTO, COOL, DRY, HEAT, FAN modes.
3. SELECT TEMPERATURE: Use the TEMP ⬆️ or TEMP ⬇️ buttons to set your desired temperature.
4. SELECT FAN SPEED: Press the FAN SPEED button to choose AUTO, LOW, MED, or HIGH.
5. POINT REMOTE TOWARD UNIT: Aim the remote at the air conditioning unit.
6. PRESS POWER BUTTON: Press the ON/OFF button to start the unit.

NOT SURE WHAT A FUNCTION DOES? Refer to the "How to Use Basic Functions" and "How to Use Advanced Functions" sections of this manual for detailed descriptions.

SPECIAL NOTE:

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function's button on the remote control will have no effect.
• When there are significant differences between the "Remote Controller Manual" and "USER'S MANUAL" on function descriptions, the description in the "USER'S MANUAL" shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries

Your air conditioning unit may come with two batteries. Put the batteries in the remote control before use.

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.

BATTERY NOTES:

• For optimum product performance: Do not mix old and new batteries, or batteries of different types.
• Do not leave batteries in the remote control if you don't plan on using the device for more than 2 months.

BATTERY DISPOSAL: Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when a remote signal is received.
• Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used for more than 2 months.

NOTES FOR USING REMOTE CONTROL (Compliance)

The device could comply with local national regulations.

• In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In USA, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the "How to Use Basic Functions" section of this manual.

• ON/OFF: Turns the unit on or off. ?
• TEMP ⬆️: Increases temperature in 1°C (1°F) increments. Max. temperature is 30°C (86°F).
• SET: Scrolls through operation functions: Fresh (?) → Sleep (?) → Follow Me (?) → AP mode (?) → Fresh... The selected symbol will flash on the display area; press OK to confirm.
• TEMP ⬇️: Decreases temperature in 1°C (1°F) increments. Min. temperature is 17°C (62°F).
• FAN SPEED: Selects fan speeds in the order: AUTO → LOW → MED → HIGH. Note: Holding this button down for 2 seconds activates the Silence feature. ?️
• SWING: Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate the vertical louver auto swing feature. ?
• MODE: Scrolls through operation modes: AUTO (☁️) → COOL (❄️) → DRY (?) → HEAT (?) → FAN (?). Note: HEAT mode is not supported by cooling-only appliances.
• ECO: Press this button to enter the energy efficient mode. ?
• OK: Used to confirm the selected functions. ✔️
• TIMER: Set timer to turn the unit on or off. ⏰
• SHORTCUT: Used to restore the current settings or resume previous settings. ⭐
• CLEAN: Used to start/stop the Self Clean function. ✨
• LED: Turns the indoor unit's LED display and air conditioner buzzer on and off (model dependent), creating a comfortable and quiet environment. ?
• TURBO: Enables the unit to reach the preset temperature in the shortest possible time. ?

Model Information: For models RG10A4(D)/BGEF, RG10A4(D1)/BGEFU1, RG10A5(D)/BGEF, RG10A5(D1)/BGEFU1, RG10A5(D)/BGCEF & RG10A5(D1)/BGCEFU1 (Cooling only models, AUTO and HEAT modes are not available), RG10A11(D)/BGEF (20-28°C).

Note: For models RG10A4(D1)/BGEFU1, RG10A5(D1)/BGEFU1, and RG10A5(D1)/BGCEFU1, press the TEMP ⬆️ and TEMP ⬇️ buttons together for 3 seconds to alternate the temperature display between °C and °F. The Fresh feature is not available for models RG10A4(D)/BGEF and RG10A4(D1)/BGEFU1.

Remote Screen Indicators

Information is displayed when the remote controller is powered up.

• Transmission Indicator: Lights up when the remote sends a signal to the indoor unit.
• TIMER ON display: Indicates timer ON is set.
• TIMER OFF display: Indicates timer OFF is set.
• Silence feature display: Indicates Silence mode is active. ?
• Fresh feature display: (Some units) Shows when Fresh feature is activated. (No display when Fresh feature is activated). ?
• Sleep mode display: Shows when Sleep mode is active. ?
• Follow me feature display: Shows when Follow Me feature is active. ?
• Wireless control feature display: Shows when wireless control is active. ?
• Low battery detection display: Flashes when the battery is low. ?
• MODE display: Shows the current mode: AUTO (☁️), COOL (❄️), DRY (?), HEAT (?), FAN (?).
• ECO display: (Some units) Shows when ECO feature is activated. ?
• LOCK display: Shows when LOCK feature is activated. ?
• FAN SPEED display: Shows selected fan speed: LOW (?️), MED (?️?️), HIGH (?️?️?️), AUTO (?️ AUTO). This fan speed cannot be adjusted in AUTO or DRY mode.
• Temperature/Timer/Fan speed display: Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.
  • Temperature range: 17-30°C / 62-86°F (20-28°C) (Model dependent).
  • Timer setting range: 0-24 hours.
  This display is blank when operating in FAN mode.

Note: All indicators shown in the figure are for clear presentation. During actual operation, only the relevant function signs are shown on the display window.

How to Use Basic Functions

Basic Operation

ATTENTION! Before operation, please ensure the unit is plugged in and power is available.

Setting Temperature

The operating temperature range for units is 17-30°C (62-86°F) / 20-28°C. You can increase or decrease the set temperature in 1°C (1°F) increments.

AUTO Mode

In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT operation based on the set temperature.

1. Press the MODE button to select AUTO (☁️).
2. Set your desired temperature using the TEMP ⬆️ or TEMP ⬇️ button.
3. Press the ON/OFF button (?) to start the unit.

NOTE: FAN SPEED cannot be set in AUTO mode.

COOL Mode

1. Press the MODE button to select COOL (❄️) mode.
2. Set your desired temperature using the TEMP ⬆️ or TEMP ⬇️ button.
3. Press the FAN SPEED button to select the fan speed: AUTO, LOW, MED, or HIGH. ?️
4. Press the ON/OFF button (?) to start the unit.

DRY Mode (Dehumidifying)

1. Press the MODE button to select DRY (?) mode.
2. Set your desired temperature using the TEMP ⬆️ or TEMP ⬇️ button.
3. Press the ON/OFF button (?) to start the unit.

NOTE: FAN SPEED cannot be changed in DRY mode.

FAN Mode

1. Press the MODE button to select FAN (?) mode.
2. Press the FAN SPEED button to select the fan speed: AUTO, LOW, MED, or HIGH. ?️
3. Press the ON/OFF button (?) to start the unit.

NOTE: You cannot set the temperature in FAN mode. As a result, your remote control's LCD screen will not display temperature.

HEAT Mode

1. Press the MODE button to select HEAT (?) mode.
2. Set your desired temperature using the TEMP ⬆️ or TEMP ⬇️ button.
3. Press the FAN SPEED button to select the fan speed: AUTO, LOW, MED, or HIGH. ?️
4. Press the ON/OFF button (?) to start the unit.

NOTE: As outdoor temperature drops, the performance of your unit's HEAT function may be affected. In such instances, it is recommended to use this air conditioner in conjunction with other heating appliances.

Setting the TIMER

Set the amount of time after which the unit will automatically turn on/off.

TIMER ON Setting

Press the TIMER button (⏰) to initiate the ON time sequence. Press the TEMP ⬆️ or TEMP ⬇️ button multiple times to set the desired time to turn on the unit. Point the remote at the unit and wait 1 second; the TIMER ON will be activated.

TIMER OFF Setting

Press the TIMER button (⏰) to initiate the OFF time sequence. Press the TEMP ⬆️ or TEMP ⬇️ button multiple times to set the desired time to turn off the unit. Point the remote at the unit and wait 1 second; the TIMER OFF will be activated.

NOTE:

1. When setting TIMER ON or TIMER OFF, the time increases by 30-minute increments up to 10 hours. After 10 hours, it increases in 1-hour increments up to 24 hours. (e.g., press 5 times for 2.5h, press 10 times for 5h). The timer will revert to 0.0 after 24 hours.
2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF Setting (Example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If the current time is 1:00 PM, to set the timer as described, the unit will turn on 2.5 hours later (3:30 PM) and turn off at 6:00 PM.

How to Use Advanced Functions

Swing Function

Press the Swing button (?) to start/stop horizontal louver movement. The horizontal louver will swing up and down automatically. Press again to make it stop.

Keep pressing the Swing button for more than 2 seconds to activate the vertical louver swing function (model dependent).

LED DISPLAY

Press the LED button (?) to turn the display on and off. Press this button to turn on and turn off the display on the indoor unit.

Press this button for more than 5 seconds (some units). The indoor unit will display the actual room temperature. Pressing more than 5 seconds again will revert back to displaying the setting temperature.

Silence Function

Keep pressing the Fan button for more than 2 seconds to activate/disable the Silence function (some units). Due to low frequency operation of the compressor, it may result in insufficient cooling and heating capacity. Pressing ON/OFF, Mode, Sleep, Turbo, or Clean button while operating will cancel the silence function. ?

ECO Function

Press the ECO button (?) to enter the energy efficient mode. Note: This function is only available under COOL mode.

ECO Operation: Under cooling mode, pressing this button adjusts the temperature automatically to 24°C/75°F and fan speed to Auto to save energy (only when the set temperature is less than 24°C/75°F). If the set temperature is above 24°C/75°F, pressing the ECO button changes the fan speed to Auto, while the set temperature remains unchanged.

NOTE: Pressing the ECO button, or modifying the mode, or adjusting the set temperature to less than 24°C/75°F will stop ECO operation. Under ECO operation, if the set temperature is 24°C/75°F or above, it may result in insufficient cooling. If you feel uncomfortable, press the ECO button again to stop it.

FP Function

This function is for heat pump air conditioners only. The unit will operate at high fan speed (while the compressor is on) with the temperature automatically set to 8°C/46°F.

To activate the FP function, press the button 2 times within one second under HEAT Mode and setting temperature of 17°C/62°F or 20°C/68°F (for models RG10B10(D)/BGEF, RG10A11(D)/BGEF).

Pressing ON/OFF, Sleep, Mode, Fan, and Temp buttons while operating will cancel this function.

LOCK Function

Press the Clean button (✨) and Turbo button (?) together for more than 5 seconds to activate the Lock function. ? All buttons will not respond except for these two buttons, which can be pressed for two seconds again to disable locking.

SHORTCUT Function

Press the SHORTCUT button (⭐). When the remote controller is on, the system will automatically revert to the previous settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

If you push the button for more than 2 seconds, the system will automatically restore the current operation settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

Clean Function

Press the CLEAN button (✨). Airborne bacteria can grow in the moisture that condenses around the heat exchanger in the unit. With regular use, most of this moisture is evaporated from the unit. By pressing the CLEAN button, your unit will clean itself automatically. After cleaning, the unit will turn off automatically. Pressing the CLEAN button mid-cycle will cancel the operation and turn off the unit. You can use CLEAN as often as you like.

Note: You can only activate this function in COOL or DRY mode.

TURBO Function

Press the TURBO button (?). When you select the Turbo feature in COOL mode, the unit will blow cool air with the strongest wind setting to jump-start the cooling process.

When you select the Turbo feature in HEAT mode, for units with Electric heat elements, the Electric HEATER will activate and jump-start the heating process.

SET Function

Press the SET button (⚙️) to enter the function setting. Then, press the SET button or TEMP ⬆️ or TEMP ⬇️ button to select the desired function. The selected symbol will flash on the display area; press the OK button (✔️) to confirm.

To cancel the selected function, perform the same procedures as above.

Press the SET button to scroll through operation functions: Fresh (?) → Sleep (?) → Follow Me (?) → AP mode (?).

Note: If your remote controller has dedicated Fresh and Sleep buttons, you cannot use the SET button to select these features.

FRESH Function (?) (Some units):

When the FRESH function is initiated, the ion generator is energized and will help to purify the air in the room.

Sleep Function (?):

The SLEEP function is used to decrease energy use while you sleep (and don't need the same temperature settings to stay comfortable). This function can only be activated via remote control. For details, see "Sleep Operation" in the "USER'S MANUAL". Note: The SLEEP function is not available in FAN or DRY mode.

AP Function (?) (Some units):

Choose AP mode to do wireless network configuration. For some units, it doesn't work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

Follow Me Function (?):

The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes. When using AUTO, COOL, or HEAT modes, measuring ambient temperature from the remote control (instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

NOTE: Press and hold the Turbo button (?) for seven seconds to start/stop the memory feature of the Follow Me function.

• If the memory feature is activated, "On" displays for 3 seconds on the screen.
• If the memory feature is stopped, "OF" displays for 3 seconds on the screen.
• While the memory feature is activated, pressing the ON/OFF button, shifting the mode, or a power failure will not cancel the Follow Me function.

Contact Information

KLIMAIRE

7999 NW 81 Place - Medley, FL 33195 USA

Tel: (305) 594 - 4972 Fax: (305) 675-2212

www.klimaire.com | sales@klimaire.com

The Klimaire logo is a registered trademark of Klimaire Products, Inc. Copyright 2025.

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.