Holy Stone HS460 Drone User Manual
Thank you for purchasing the Holy Stone HS460 drone. This manual provides comprehensive instructions for setup, operation, and maintenance.
Contact Information:
- USA: usa@holystone.com, +1 (833) 766-4733
- EU: eu@holystone.com
- AU: au@holystone.com
Product Overview
The HS460 is a quadcopter drone designed for aerial photography and videography. It features GPS positioning, a high-definition camera, and a user-friendly transmitter.
Package Contents
The package typically includes:
- 1x HS460 Drone
- 1x Transmitter
- 1x Drone Battery
- 1x USB Charging Cable
- 1x USB Adapter
- Propellers (A and B)
- Screwdriver
- User Manual
Drone Diagram
The drone features:
- Propellers (A and B)
- Drone Status Light
- Camera
- Battery Lights
- Power Button (long press to turn on/off)
- TF Card Slot
- Optical Flow Lens
- Drone Battery
Powering On/Off: Long press the power button on the drone to turn it on or off. The status lights indicate the flight control system's status, and battery lights show the remaining battery level.
Transmitter Diagram
The transmitter includes:
- Front:
- Mobile Phone Holder
- Power Button (short press to turn on/off)
- Headless Mode Button (short press)
- Return to Home/GPS Switch (short press)
- Right Joystick (controls throttle, yaw, pitch, roll; short press for video recording, lens up)
- Left Joystick (controls throttle, yaw, pitch, roll; short press for unlock/takeoff/landing, long press for compass calibration)
- Top:
- Charging Port
- Bottom:
- Foldable Handgrip
- Video Recording Button (short press)
- Photo Button (short press)
- Lens Up/Down Controls
Joystick Modes
The default mode is MODE 2. In this mode:
- Left Joystick: Up (Ascend), Down (Descend), Left (Yaw Left), Right (Yaw Right)
- Right Joystick: Up (Pitch Forward), Down (Pitch Backward), Left (Roll Left), Right (Roll Right)
Charging Instructions
Drone Battery Charging:
- Remove the battery from the drone.
- Connect it to the USB charging cable and plug into a 5V/2A USB adapter or power bank.
- Charging indicators: Red light solid, green light blinking while charging; both lights solid when fully charged.
- Charging time: Approximately 180 minutes.
Transmitter Charging:
- Connect the USB charging cable to the transmitter's charging port and plug into a 5V/2A USB adapter or power bank.
- Charging indicator: The indicator light on the transmitter turns on while charging and turns off when fully charged.
- Charging time: Approximately 60 minutes.
Important: Read the battery safety instructions before charging. Do not charge the battery immediately after flight if it is hot. Allow it to cool to room temperature.
Pre-Flight Preparations
Folding Arms
Unfold the drone arms before flight: first the front arms, then the rear arms.
TF Card Installation
Insert a TF card (Class 10 or higher, up to 64GB) into the TF card slot to save photos and videos.
Propeller Installation
Ensure the correct propellers (marked 'A' or 'B') are attached to the corresponding motor shafts. Secure them with screws by tightening clockwise. To remove, use the screwdriver to loosen screws counter-clockwise while holding the motor.
Drone Battery Installation
Ensure the battery is correctly inserted into the drone until it clicks. To remove, press the battery lock button and pull the battery out.
Transmitter Setup
Unfold the foldable handgrip. Adjust the clamp to securely hold your mobile phone.
Transmitter Signal Range
Maintain optimal signal reception by adjusting the orientation and distance between the transmitter and the drone.
Pre-Flight Checklist
- Ensure the transmitter, mobile phone, and drone battery are fully charged.
- Ensure the camera lens is clean.
- Ensure the motors are not blocked.
- Ensure the drone battery and propellers are securely mounted.
Flight Operations
Pairing the Transmitter and Drone
- Place the drone on a flat surface. Long press the power button to turn on the drone (red status lights will blink).
- Short press the power button on the transmitter to turn it on (indicator light will blink).
- Move the left joystick up and then down to pair. Successful pairing is indicated by the transmitter's indicator light changing from blinking to solid.
Wi-Fi Connection
- Go to your phone's Wi-Fi settings.
- Connect to the drone's Wi-Fi network (e.g., "HolyStoneFPV-XXXX").
- Launch the "HS GPS V5" app. A live video feed should appear in the app.
Note: The drone's Wi-Fi does not provide internet access. Ignore any warnings about unsafe or no internet connection.
Compass Calibration
- Step 1: Long press the compass calibration button on the transmitter (it will beep).
- Step 2: Hold the drone horizontally and rotate it three times. Status lights will change from fast to slow blinking.
- Step 3: Hold the drone vertically (nose up) and rotate it three times. Status lights will turn solid green or double red blink, indicating successful calibration.
Recommendation: Calibrate the compass before each flight, especially in areas prone to magnetic interference.
GPS Signal Search
After compass calibration, place the drone on a flat surface. The drone will automatically search for GPS signals. Solid green status lights indicate a successful GPS lock.
GPS Mode: The default mode is GPS. Once GPS is acquired outdoors, the drone will remain in GPS mode. If GPS signal is weak or flying indoors, you can exit GPS mode by short pressing the RTH button. The drone will be ready to unlock and take off with a solid yellow light, but GPS functions will be unavailable.
Gyro Calibration
Ensure the drone is on a flat surface. Simultaneously push both joysticks to the bottom right corner. The drone's status lights will blink and then turn solid, indicating completion.
Recommendation: Calibrate the gyro after pairing and after any crash.
Motor Unlock
Short press the unlock button. The motors will spin, and the drone is unlocked.
Takeoff/Landing
- Takeoff: After unlocking motors, short press the takeoff/landing button. The drone will automatically ascend to about 1.2 meters and hover.
- Landing: During flight, short press the takeoff/landing button. The drone will automatically land.
Speed Control
Short press the left joystick to switch between low (1 beep) and high (2 beeps) speed modes. Max speed: 9 m/s.
Camera Angle Adjustment
Use the dedicated buttons on the transmitter to tilt the camera up or down within a range of -70° to 0°.
Photo/Video Recording
- Video: Short press the video button. Two beeps indicate recording start; one long beep indicates recording stop.
- Photo: Short press the photo button. One beep indicates a photo has been taken.
Headless Mode
Activation: Short press the headless mode button (2 beeps). The drone will fly in the direction the joystick is pushed, regardless of its orientation.
Deactivation: Press the button again (1 beep). The drone returns to normal mode.
Why Orientation Matters: In normal mode, the drone's direction affects control. In headless mode, the drone remembers its initial 'head' direction, making controls intuitive.
Emergency Stop
In an emergency, long press the emergency stop buttons simultaneously. The drone will descend rapidly. Use with caution as it may cause damage.
Return to Home (RTH)
Smart RTH: Press the RTH button when the GPS signal is strong and a Home Point is recorded. The drone will return to the Home Point. Pressing the button again cancels RTH.
Failsafe RTH: Activates automatically if the transmitter connection is lost for over 15 seconds (requires strong GPS and recorded Home Point).
RTH Altitude: If the drone is below 20m, it will ascend to 20m before returning. If above 20m, it maintains current altitude. Be aware of obstacles during RTH.
Stabilization Functions
Optical Flow Positioning
The optical flow system uses a camera to track visual features for precise positioning, especially useful indoors or where GPS is weak. It works best at altitudes below 0.5-3 meters.
Limitations: Performance can be affected by lighting, surface textures, and movement. Avoid flying over featureless, very dark/bright, or reflective surfaces. Ensure sensors are clean and the environment is suitable.
App Functions
Interface Overview
- Main Menu: Return to the main menu.
- Status Bar: Displays drone status.
- GPS Signal: Shows GPS signal strength.
- Drone Battery Level: Real-time battery status.
- Flight Settings: Adjust flight parameters like altitude and distance limits.
- Speed: Current speed mode.
- Takeoff/Landing: Initiate takeoff or landing.
- Return to Home: Initiate RTH.
- Multi-functions: Access advanced features like GPS Follow, Waypoint, and Orbit.
- VR Mode: For viewing 3D live feeds with compatible VR goggles.
- Map View: Switch between camera and map views.
- Flight Distance/Altitude: Displays distance and altitude from the Home Point.
- Flight Attitude Display: Shows drone orientation and position relative to the operator.
- Flight Record: Logs flight parameters.
- Photo/Video: Switch between photo and video modes.
- Shutter Button: Take photos or start/stop video recording.
- Album: View captured photos and videos.
Beginner Mode
The default mode limits flight distance to 30m and altitude to 30m. Disable Beginner Mode in the app settings to access full flight parameters.
Drone Status Light Meanings
| Light Status | Meaning |
|---|---|
| Red Slow Blinking | Unsuccessful pairing after powering on drone. |
| Yellow Double Blinking | Successfully paired / Searching for GPS signals. |
| Green Solid | GPS signal search successful. |
| Yellow Solid | Successfully exited GPS mode. |
| Red Double Slow Blinking | Initiated second stage of low-voltage RTH. |
| Red Double Fast Blinking | Low voltage warning. |
Technical Specifications
Drone
- Model: HS460
- Weight: 214g
- Max Flight Time: 26 minutes
- Max Flight Altitude: 328 ft / 100m
- Max Wind Resistance: 3.5 m/s
- Max Takeoff Altitude: 11483 ft / 3500m
- Max Flight Speed: 9 m/s
- Operating Temperature: 0° to 40°C
- Dimensions (Folded): 266 × 220 × 55 mm
- Dimensions (Unfolded): 125 × 81 × 55 mm
Drone Battery
- Model: HW782768
- Capacity: 1700mAh
- Voltage: 7.6V
- Energy: 12.92Wh
- Battery Type: Lithium-ion Polymer
- Charging Temperature Range: 5° to 40°C
- Charging Time: Approx. 180 minutes
USB Charging Cable
- Input: 5V/2A
- Rated Power: <10W
Transmitter
- Operating Frequency: 2408-2472MHz
- Max Flight Distance: 1640 ft / 500m
- Battery Type: 3.7V 380mAh Lithium-ion Polymer
- Operating Temperature: 0° to 40°C
- Charging Time: 60 minutes
Camera
- Operating Frequency: 5150-5250MHz
- Controllable Range: -70° to 0°
- Photo Resolution: 3840*2160P
- Video Resolution: 2048*1152P@25fps (TF Card), 1920*1080P@25fps (Phone)
- Max Transmission Distance: 1640ft / 500m
- Lens: FOV 100°
- Photo Format: JPEG
- Video Format: MP4
- Supported TF Cards: Class 10 or higher, up to 64GB
- Supported File Systems: FAT32
Troubleshooting
| Problem | Possible Cause | Suggested Solution |
|---|---|---|
| Motors do not start | Weak GPS reception. | Fly in an area with good GPS reception. For indoor use, short press the RTH button to exit GPS mode. |
| Drone battery is low (indicated by blinking red light). | Charge the battery. | |
| Compass not calibrated. | Perform compass calibration. | |
| Unstable flight or abnormal attitude | GPS signal instability near buildings or obstacles. | Fly in open areas free from obstacles. |
| Compass interference. | Land immediately, recalibrate compass, or try a different location. | |
| Drone malfunction or after a crash. | Calibrate the drone on a flat surface by moving both joysticks to the bottom right corner until drone lights are solid. | |
| Unstable air pressure or poor optical flow. | Consider flying in a more suitable environment. | |
| Propeller deformation or damage. | Replace propellers. | |
| TopFly function cannot be performed. | Map not pre-loaded. | Pre-load the map using mobile data or Wi-Fi. |
| Flight too low. | Use this function at altitudes of 15 meters or higher. |
Compliance Information
EU RF Power
EIRP: <10 dBm (2400MHz-2472MHz)
Manufacturer Information
Manufacturer: XIAMEN HUOSHIQUAN IMPORT & EXPORT CO.,LTD
Address: Unit 1, Room 501, Hongxiang Building, No.258 Hubin Nan Road, Siming District, Xiamen, China
MTOM Declaration
The HS460 has a Maximum Take-Off Mass (MTOM) of 214g, complying with C0 requirements. Do not add unauthorized accessories or parts.
Safety Precautions
- Use the Emergency Stop function in critical situations.
- Refer to sections on Optical Flow Positioning and Return to Home for stabilization features.
- Avoid flying in restricted airspace.
The firmware of this toy product cannot be upgraded. App updates are available through the App Store (search for "HS GPS V5").
