YR10F Setting Sheet
Driver: Tyronne Wilken
Date: 2017-03-04
Circuit: Welkom - SARDA Nationals (TQ & Win)
Environment: Indoor ✔️, Outdoor
Track: Asphalt ✔️, Carpet
Traction: High ✔️, Medium, Low
Track Situation: Flat ✔️, Bumpy
Temperature: [Not Specified], Humidity: [Not Specified]
Front Suspension Settings
Description: This section details the front suspension geometry and components.
Wheel Offset and Camber Angle
Configuration: Wide / Narrow
Camber Angles:
- 1°
- 1.5°
- 2°
- 2.5°
Visual Description: Diagrams show circular indicators for camber angles from 1° to 2.5°.
Spacers and Ride Height
Spacers: Various spacer sizes are used to adjust suspension geometry:
- 2 mm spacer (for lower arm)
- 4 mm spacer (for upper arm mount)
- 0.5 mm spacer (for upper arm mount)
- 0 mm spacer (for upper arm mount)
Visual Description: Diagrams illustrate the placement of these spacers on the front suspension components.
Caster Angle
Caster Angles:
- Upper: 6°, 9°, 12°
- Lower: 6°, 9°, 12°
Visual Description: Diagrams show circular indicators for caster angles from 6° to 12° for upper and lower positions.
Ride Height
Ride Height: 3.5 mm
Visual Description: A ruler-like graphic indicates the measurement for ride height.
Tread
Tread: [Value not specified]
Visual Description: A diagram shows the width of the front tires.
Toe Angle
Toe Angle: 1.5°
Rebound
Rebound: [Value not specified]
Visual Description: A diagram indicates the shock rebound setting.
Spring
Spring: Xray Silver
Wing
Wing: Montech
Notes
- 10K Lube on kingpin.
- 4 Additional holes drilled for more options on ackerman, same spacing used as existing holes. Used the lowest option.
- Front bulkheads replaced with BD-201 P7 posts.
Rear Shock Settings
Description: Details the rear shock absorber configuration.
Rear Shock Position
Position: [Value not specified]
Visual Description: A diagram shows the mounting positions for the rear shock absorber.
Ride Height Adjustment
Spacer Options for Ride Height:
| Spacer Size | Hole Position (Top/Bottom) |
|---|---|
| 0 mm | Top ✔️ / Bottom |
| 0.25 mm | Top / Bottom |
| 0.5 mm | Top / Bottom |
| 0.75 mm | Top / Bottom |
| 1.0 mm | Top / Bottom |
| 1.25 mm | Top / Bottom |
| 1.5 mm | Top / Bottom |
| 1.75 mm | Top / Bottom |
| 2.00 mm | Top / Bottom |
Visual Description: A table lists various spacer sizes (0mm to 2.00mm) used to adjust the rear shock absorber's ride height, with options for top or bottom mounting.
Shock Absorber Details
Hole Height: 4.5 mm
Shock Absorber:
- Pitch: [Value not specified]
- Oil: 1000
- Spring: Kit
Roll Settings
Roll:
- Oil: 30K
- Side Spring: Kit
Shock Length: 62.5 mm
Spacers: 7 mm spacer (for shock mount), 2 mm spacer (for lower shock mount).
Visual Description: Diagrams show the shock absorber assembly with specific spacer placements and the overall shock length.
Other Components and Settings
Description: Details on motor, battery, ESC, radio system, body, and tire treatments.
Motor
| Type | Motiv Mcode 21.5 |
|---|---|
| Timing | 37 |
| Gearing (Spur Gear) | 76 |
| Gearing (Pinion Gear) | 33 |
Battery
| Type | Turnigy 4600 90C |
|---|
Electronic Speed Controller (ESC)
| Type | Team Powers XPS |
|---|
Radio System
| Transmitter | Futaba T4PKS |
|---|---|
| Receiver | Futaba R604FS |
| Servo | Futaba |
Body
| Type | Protoform F15 |
|---|
Tires
| Position | Tire Type | Diameter | Wheel |
|---|---|---|---|
| Front | Ride XR | [Value not specified] mm | [Value not specified] |
| Rear | Ride XR | [Value not specified] mm | [Value not specified] |
Tire Treatment
| Position | Treatment | Treatment Area |
|---|---|---|
| Front | Paragon FX II | Left, Right |
| Rear | Paragon FX II | Left, Right |
Visual Description: Diagrams show the tire treatment application areas on the left and right sides of the tires.
Setup Adjustments
| Steering Expo | -15% |
|---|---|
| Brake End Point (E.P.) | 30 |
| Throttle Expo | 100% |
