ASUS PCIe Wi-Fi Card / Intel AX200 Installation

Installation Steps

1. Install the M.2 Wi-Fi card into the M.2 Wi-Fi slot.

   Diagram Description: Shows the M.2 Wi-Fi card being inserted into its designated M.2 slot.

2. Firmly insert the pin ends of the two RF cables into the holes on the M.2 Wi-Fi card.

   Diagram Description: Illustrates connecting the small connectors of the two RF cables to the pins on the M.2 Wi-Fi card.

3. Attach the plastic cover to the M.2 Wi-Fi card and secure it with the bundled screw.

   Diagram Description: Shows a plastic cover being placed over the M.2 Wi-Fi card and fastened with a small screw.

4. Insert the two RF cables separately into the bracket and secure them with the bundled screws.

   Diagram Description: Depicts the RF cables being routed and secured into a mounting bracket.

5. Install the M.2 Wi-Fi card into the PCIe slot on your motherboard.

   Diagram Description: Shows the assembled M.2 Wi-Fi card and bracket being inserted into a standard PCIe slot on the motherboard.

6. Connect the USB 2.0 cable to the BT_USB header on the M.2 Wi-Fi module.

   Diagram Description: Illustrates connecting one end of the USB 2.0 cable to the specific BT_USB header on the M.2 Wi-Fi card module.

7. Connect the USB 2.0 cable to the USB 2.0 header on your motherboard.

   Diagram Description: Shows the other end of the USB 2.0 cable being connected to a standard USB 2.0 header on the motherboard.

8. Install the bracket to your chassis.

   Diagram Description: Shows the bracket assembly being mounted to the computer's chassis.

9. Connect the bundled antenna to the RF cable.

   Diagram Description: Illustrates connecting the external Wi-Fi antenna to the RF cable connector on the installed bracket.

Important Notes & Warnings

• ⚠️ This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and your body.
• Before installing and using the M.2 card, carefully read the manual that came with the package.
• Use ONLY the bundled RF cable and antenna.
• Any changes or modifications to this device not expressly approved by ASUS could cause harmful interference to radio communications and void the user's authority to operate the equipment.

Regulatory Information

FCC Compliance Information

Responsible Party: Asus Computer International

Address: 48720 Kato RD., Fremont, CA 94538

Phone / Fax No: (510)739-3777 / (510)608-4555

Identification of the assembled product: PCIE WIFI CARD/INTEL AX200

Identification of the modular components used in the assembly: Model Name: AX200NGW FCC ID: PD9AX200NG

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Warning

This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Innovation, Science and Economic Development Canada (ISED) Compliance

This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B)/NMB-3(B)

Simplified EU Declaration of Conformity

ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.com/support/.

The WiFi operating in the band 5150-5350MHz shall be restricted to indoor use for countries listed in the table below.