XB-024 Bluetooth Game Controller - Product Specifications

Product Description

This product is a Switch Pro Bluetooth game controller, connecting to the Switch console via Bluetooth and also supporting wired connection.

Product Features

• Includes all buttons and functions of the original Switch controller, with added turbo speed, motor vibration, and 3D joystick sensitivity adjustment functions.
• Provides 4-channel LED status indicators, with light ring effects for the left and right 3D joysticks.
• Equipped with a dedicated Bluetooth "pairing" [NS Button] button.
• Built-in HD dual motors, Hall effect high-precision 3D joysticks.
• Two switch buttons on the back to independently turn on/off the 3D light rings and motor vibration function.
• The controller's [HOME Button] can wake up the console; [HOME Button] can also wake up the controller to reconnect to the console.
• Equipped with a 6-axis gyroscope for fast and accurate target locking.
• Compatible with PC consoles, supports XINPUT mode.

Function Description

Controller Connection Methods:

• Wired connection: Connect to the Switch console using a USB data cable.
• Bluetooth connection: Connect to the Switch console via Bluetooth communication.

Bluetooth Connection to Switch Console:

• When the Switch console is on, navigate to the pairing interface in the console's settings.
• Long press the controller's [NS Button] for approximately 3 seconds until the LED1-4 indicators flash in a scrolling pattern. Release the button.
• Perform Bluetooth pairing on the Switch console. Once successfully paired, all controller functions can be used normally, and the console will assign a channel LED indicator that stays lit. If pairing fails, the controller will automatically enter sleep mode after 60 seconds.

Bluetooth Pairing Modes:

• XINPUT Mode (for PC/Android/etc.): When in sleep mode, long press the [BT Button] for 3 seconds to enter XINPUT mode pairing. The indicator lights (LED1, LED4) will flash rapidly. Search for the Bluetooth device named "Xbox Wireless Controller" on your device and connect.
• DINPUT Mode (for PC/Android/etc.): When in sleep mode, long press the [BT Button] and [A Button] simultaneously for 3 seconds to enter DINPUT mode pairing. The indicator lights (LED2, LED3) will flash rapidly. Search for the Bluetooth device named "Gamepad" on your device and connect.
• 2.4G Mode (for PC/Android/etc.): When in sleep mode, long press the [2.4G Button] for 3 seconds. The controller can connect to Windows computers or Android TVs using the 2.4G receiver.

Note: Pressing the [HOME Button] can reconnect to the mode used before the last shutdown.

• Press [NS Button] to reconnect to the Switch console.
• Press [BT Button] to reconnect in XINPUT mode.
• Press [BT Button] and [A Button] to reconnect in DINPUT mode.
• Press [2.4G Button] to reconnect to the receiver.

Console Wake-up:

• When the controller is connected to the Switch console, if the console enters sleep mode, pressing the controller's [HOME Button] can wake up the console.

PC Connection (XINPUT Mode):

• When connected to a PC via USB data cable, the device will be recognized as "Xbox 360 Controller", enabling Xbox 360 controller functionality.
• While in Xbox 360 mode, simultaneously press the [Screenshot Button] and the directional [Down Button] to swap the button assignments of A, B, X, Y. This will switch to the Xbox 360 button layout. Performing this action again or disconnecting and reconnecting the PC will restore the Switch Pro controller button layout.

Firmware Update:

• If certain controller functions do not work correctly due to Switch console firmware updates, the controller may require a firmware update. The controller does not support automatic updates via the Switch console; users must obtain the update program and instructions, and connect to a PC for the update.

Button Programming (Mapping) Mode Operation Steps

1. Press and hold the [M Button] for programming mode for 2 seconds. The left and right 3D light rings will flash slowly, indicating the controller has entered programming mode.
2. Press any button you wish to program (map), such as A/B/X/Y/LB/RB/L3/R3/D-PAD. The left and right 3D light rings will flash rapidly.
3. Press either the left or right programming button. The left and right 3D light rings will change from rapid flashing to a steady glow, indicating successful button programming (mapping).
4. Note: Up to 16 buttons can be programmed. If no button is pressed for over 1 minute, programming mode will exit automatically.
5. To program the next button, repeat step 3.

Note: Programmed functions are retained after power off.

Clear Programming (Mapping) Function

1. Press and hold the [M Button] for programming mode for 2 seconds. The left and right 3D light rings will flash slowly, indicating the controller has entered programming mode.
2. Press the [ML Button] or [MR Button] for the programming key you wish to clear. The left and right 3D light rings will flash and then turn solid, indicating that all programming (mapping) functions have been cleared.

Turbo Function and Speed Adjustment

The controller supports rapid fire and rapid fire speed adjustment. To activate rapid fire: hold the [TURBO Button] and press a function button, then release both. Pressing the function button again will trigger rapid fire. Pressing the function button while holding [TURBO Button] again will enable auto-fire. To pause auto-fire, press the button once. To cancel rapid fire for that button, repeat the previous steps or long press the [TURBO Button] for 3 seconds to clear all button rapid fire functions.

To adjust rapid fire speed: hold the [TURBO Button] and move the right 3D joystick up or down. The speed can be adjusted in three levels: fast, medium, and slow. The default is slow. (Factory lock mode will also clear all button rapid fire functions).

Controller Wake-up and Standby

• When the controller is powered on, long press the [HOME Button] for 5 seconds to turn off the controller.
• If the controller is in pairing mode and fails to pair within 60 seconds, it will automatically enter standby mode.
• If the controller is connected to the console and remains inactive for 5 minutes, it will automatically enter standby mode.

Reset Function

If the controller malfunctions, you can reset it by long pressing the [HOME Button] for 10 seconds to turn it off and reset.

Receiving Distance

The controller's effective receiving distance is within 10 meters.

Reference Current

• Sleep current: ≤ 5µA
• Working current (without vibration): ≤ 90mA
• Working current (with vibration): ≤ 180mA
• Pairing current: ≤ 86mA

Controller Electrical Specifications

• Power supply method: Built-in polymer battery
• Battery capacity: 800mAh
• Charging voltage: DC 5V
• Playtime: 10 hours
• Charging time: Approximately 2.5 hours
• Maximum charging current: 500mA

Bluetooth Connection Guide for Switch Console

Step 1: Turn on the Switch console. Click the "house" icon on the right side of the screen to enter the main menu.

Step 2: Click the "Controllers" option on the Switch console's main menu.

Step 3: Select "Change Grip/Order" from the menu.

Step 4: Enter the "Change Grip/Order" screen. Long press the controller's [NS Button] for 3 seconds to initiate pairing. The 4 LED indicators will flash rapidly. Release the [NS Button]. Wait for 5 to 30 seconds. The controller will connect to the console, and the console screen will display the controller icon. The assigned channel LED indicator on the controller will stay lit.

Factory Reset ("Lock Mode")

When the controller is powered on (connected to the console or PC), long press the [L1 Button] and [L3 Button] for 3 seconds. The 4 channel indicators will light up for 1 second. Then, press the [HOME Button] to power off. The controller will enter "Lock Mode". In "Lock Mode", all button functions are disabled to prevent accidental activation during packaging and shipping. This mode is set before the product leaves the factory.

Exiting "Lock Mode"

When the controller is in "Lock Mode", no buttons can wake it up. To exit "Lock Mode", connect the controller to a USB data cable for charging. This will restore normal controller functions.

Calibrating Controller Gyroscope Sensor with Switch Console

After the Switch console and controller are successfully connected, return to the console's home screen. Navigate to "Settings" > "Controllers & Sensors" > "Calibrate Motion Controls". In the pop-up menu, select "Calibrate Controller". On the controller calibration screen, place the controller on a flat surface. Follow the on-screen prompts, long pressing the controller's [- Button] or [+ Button] to complete the gyroscope calibration. The calibration screen shows prompts like "Hold or on the controller you want to calibrate."

Calibrating Controller 3D Joysticks with Switch Console

After the Switch console and controller are successfully connected, return to the console's home screen. Navigate to "Settings" > "Controllers & Sensors" > "Calibrate Control Sticks". On the "Calibrate Control Sticks" confirmation screen, press the controller's [X Button]. A prompt menu will appear. Press the controller's [A Button] to confirm calibration. On the joystick calibration screen, follow the on-screen prompts to perform movements for the joysticks, such as moving them up, down, left, right, and in a circular motion. The screen displays "Move the stick toward and release it when the color of the triangle changes."