PETLIBRO Granary Automatic Pet Feeder - User Manual

Safety Guidelines

WARNING

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation; keep away from children and pets.
• Do NOT allow small children to play with, in or around the pet feeder.
• To reduce the risk of injury, please keep close supervision when an appliance is used near children.
• Do NOT use the feeder with pets not able to reach the food tray or with any physical disability.
• Do NOT immerse the base part in water at any time as it may damage electronic components like the control panel.
• Do NOT place any foreign object in the pet feeder.
• Do NOT use outdoors. Check operation frequently to be sure the unit is dispensing properly.
• Do NOT use wet, canned or moist food.
• Do NOT disassemble the unit other than as instructed in this User Guide.
• Do NOT use the feeder for anything other than its intended use.
• Only use attachments recommended or sold by the manufacturer. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do not modify the pet feeder.
• Do not operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the pet feeder yourself. Contact customer service immediately for further instructions.
• Always unplug when not in use and before cleaning.
• Never pull on the electrical power cord to remove the plug from the wall outlet.
• If the plug of this device gets wet, turn off electricity to that wall outlet. Do not attempt to unplug.
• Examine the feeder after installation. Do not plug in if there is water on the power cord or plug.
• To avoid tripping, always position power cord out of the way of foot traffic.

CAUTION

• Do NOT allow pets to chew on or swallow any parts. If you are concerned about the power cord, purchase a cord conduit (a hard-plastic protector) at any hardware store to protect the power cord.
• If an extension cord is necessary, one unit with a proper rating should be used.
• Do NOT install or store the pet feeder where it will be exposed to weather or temperatures below 4°C / 40°F.
• Use alkaline D batteries to power. Do NOT use rechargeable batteries.
• Check the batteries regularly. Before leaving for extended time, always replace batteries with new ones.
• Do NOT lift the pet feeder by lid, food tank, or food tray. Lift and carry it using both hands and the base, while keeping the unit in an upright position.
• Suitable for dry food ONLY, with kibble size ranging from 2-15mm / 0.07-0.6in in diameter. Larger kibble may get stuck at the food outlet.
• Do not put your fingers into the food outlet or let your fingers touch the rotor.
• Read and observe all important notices listed on the pet feeder and in the packaging.

FCC Compliance and Radiation Exposure

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Radiation Exposure Statement: To maintain compliance with FCC's RF Exposure guidelines, This equipment should be installed and operated with minimum distance of 20cm from your body.

Warranty

• 1-year warranty
• Lifetime support

For guidance on product use and warranty extension, please contact PETLIBRO brand after-sales staff via email: support@petlibro.com

If any questions related to orders, please contact the seller through the shopping platform.

In the Box

The following items are included:

• Automatic Pet Feeder (x1)
• Double Food Bowls with Holder (x1)
• Meal Splitter (x1)
• Power Adapter (x1)
• User Guide Kit (x1)
• Desiccant Bag (x1)

Product Overview

The PETLIBRO Granary Automatic Pet Feeder consists of the following parts:

• 1: Lid
• 2: Seal Strip
• 3: Food Tank
• 4: Transparent Window
• 5: Tank Base
• 6: Anti-Clog Detector
• 7: Meal Splitter
• 8: Stainless Steel Bowls
• 9: Control Panel
• 10: Display Panel
• 11: Food Outlet
• 12: Bowl Holder
• 13: Feeder Base

Additional components:

• 14: Desiccant Box (integrated into the lid)
• 15: Power Jack (on the back of the feeder)
• 16: Power Adapter
• 17: Battery Compartment (at the bottom of the feeder)
• 18: Compartment Lid
• 19: Speaker

Buttons and Display Overview

The feeder has several buttons and a display panel:

Buttons:

• Unlock Button: Press and hold for 3 seconds to unlock other buttons and the screen.
• Manual Feeding Button: Press 1-5 times to dispense 1-5 portions of food.
• Record Button: Press once for a beep ?. Speak and record your message (max 10 seconds). Press again to save (two beeps ?? indicate saving).
• Number Decrease Button: In unlocked status, press to switch between meal numbers. In setting status, press to decrease the number.
• Number Increase Button: In unlocked status, press to switch between meal numbers. In setting status, press to increase the number.
• Setting Button: In setting status, press to confirm and enter the next step. Press and hold for 3 seconds to return to the locked interface.

Display Icons:

• Time Setting Icon (⏰): Indicates readiness for current time setting.
• Battery Level Icon (?): Lights up when batteries are installed. Turns red and flashes when battery level is low, indicating batteries need replacing.
• Lock Icon (?): Lights up when other buttons are locked.
• Record Icon (?): Indicates readiness for setting the times for meal calls.
• Meal Number Indicators (1️⃣, 2️⃣, 3️⃣, 4️⃣, 5️⃣, 6️⃣): Show the selected meal number.
• AM/PM Indicator: Shows AM or PM for the time.

The display area shows time, number of feedings, and recording playback status.

How to Use

Assembly and Prepare for Setting

1. Twist the lid anticlockwise to open it.
2. Place the desiccant bag [desiccant bag] into the inner box under the lid.
   • Note: It is recommended to change the desiccant bag every 15 days to prevent mold growth.
   • Remove the desiccant bag before cleaning the lid.
3. Add dry pet food to the food tank [food tank].
   • Notes:
   • To prevent uneven food dispensing, add enough pet food to the visible level.
   • Recommended kibble size: 2-15mm / 0.07-0.6 inch in diameter. Larger kibble may get stuck at the food outlet [food outlet].
   • Do not use canned, wet, or moist food.
4. Put the lid back on. To snap into place, turn the lid clockwise from the right rotating sign to the left rotating sign.
5. Take out and install the double food tray [food tray]. Attach the double food tray to the notch underneath the feeder base.
6. Install the meal splitter [meal splitter] by aligning it with the round hole.

Adjusting Food Dispensing Amount

To dispense the same amount of food, move the splitter to its end – to its maximum right (slightly leaning towards the right from the middle of the food outlet until it can't be moved). This ensures Left = Right food amount.

If the splitter lies in the middle, the feeder may not dispense an equal amount of food (Left ≠ Right).

Note: To remove the bowl holder [bowl holder] from the feeder base, move the meal splitter away from the food outlet.

If there is grain in the food bowl, handle it gently to avoid spilling. Hold the base instead of any other parts when lifting the feeder.

Connect Power

1. Plug the 5V power adapter [power adapter] into a power socket [power socket] and the USB cable [USB cable] into the USB port on the back of the feeder.
2. The LED display [LED display] will light up automatically to indicate the feeder is on.
3. Open the battery compartment [battery compartment] at the bottom of the feeder. Install three alkaline D batteries (not included) in case of a power outage. Ensure batteries match positive and negative poles with compartment markings.
4. After batteries are installed, the battery icon (?) will light up. When the icon turns red and flashes, the battery level is low and batteries need replacing.

Notes:

• Batteries are not included.
• Do not use batteries as the sole power source to avoid sudden power outages affecting feeding. Batteries are for emergency use only.
• To prevent battery leakage, remove batteries if the device will not be used for an extended period.

Program Setting

1. Set the Current Time

Please use the 12-hour AM/PM format. Time changes automatically.

1. Press and hold the Unlock Button (?) for 3 seconds to unlock buttons and screen. The Time Setting Icon (⏰) will flash, indicating setting mode.
2. Press the Setting Button (⚙️). The hour digits will flash.
3. Use the Increase/Decrease buttons (+/-) to set the current hour. Press the Setting Button (⚙️) to save and move to the minutes.
4. The tens digit of the minute flashes. Use Increase/Decrease (+/-) to set the tens digit, then press Setting Button (⚙️) to save. Set the single digit and press Setting Button (⚙️) to save. Current time setting is complete.

Note: Control buttons and screen lock automatically after 1 minute of standby.

2. Set the Time and Portion of Meals

Set the time of the first meal

1. After setting the current time, the feeder enters feeding plan setting mode. The '1️⃣' icon will flash, indicating readiness for the first meal settings.
2. Press the Setting Button (⚙️) to set the feeding time of the first meal. The hour digits will flash.
3. Use Increase/Decrease (+/-) buttons to set the hour. Press Setting Button (⚙️) to save and move to minutes.
4. The tens digit of the minute flashes. Use Increase/Decrease (+/-) to set the tens digit, then press Setting Button (⚙️) to save. Set the single digit and press Setting Button (⚙️) to save.

Set the portion of the first meal

Once the first meal time is set, the feeder enters portion setting mode. The screen will display P-XX (XX for portions).

1. Press Increase/Decrease (+/-) buttons to set the portion (Max 50). Set the tens digit first, press Setting Button (⚙️) to save. Set the single digit, press Setting Button (⚙️) to save.

Note: The default feeding times for the first four meals are 6:00 AM, 12:00 PM, 6:00 PM, 12:00 AM. The fifth and sixth meal times are 1:00 AM. The default portion is 0. These can be changed.

3. Record a Meal Call

1. In unlocked state, press the Record Button (?) once. A beep ? will be heard.
2. Speak and record your message (max 10 seconds). Press the Record Button (?) again to end. Two beeps ?? confirm saving.
3. The recording will play back automatically once for review.

Notes:

• The meal call playback defaults to 2 times and plays when feeding time is up.
• The meal call does not play during manual feeding, only at designated meal times.

4. Set the Times the Meal Call Plays

The meal call can play 0-5 times per meal. If set to 0, it won't play for that meal.

1. In unlocked state, press and hold the Record Button (?) for 3 seconds. The Record Icon (?) will be on, and the Meal Icon (1️⃣) will flash.
2. Press Increase/Decrease (+/-) buttons to choose the meal number. Press the Setting Button (⚙️) to save.
3. The screen will display F-XX (playback times). Use Increase/Decrease (+/-) to set the number of times the meal call plays. Press the Setting Button (⚙️) to save.
4. Repeat for other meals.

Note: After all settings are complete, press and hold the Setting Button (⚙️) for 3 seconds to return to the locked interface.

Manually Feeding Your Pet

In the unlocked state, press the manual feeding button (?️) once. The feeder dispenses one portion of food. You can press it up to 5 times for 5 portions. The normal schedule and portion are not affected.

Clear All Settings

Press and hold the Increase/Decrease buttons (+/-) simultaneously for 6 seconds. The device will emit three beeps ???, and all screen icons will light up, indicating resetting is complete.

Clean and Care

Regular cleaning is recommended for pet health. Washable parts include: lid [lid], food tank [food tank], tank base [tank base], stainless steel bowls [stainless steel bowls], and bowl holder [bowl holder]. Clean other parts with a dry cloth.

Clean the Tank Lid, Food Tank, Tank Base

Before removing the food tank, ensure it is empty to prevent spills.

1. Disconnect power before cleaning.
2. Twist the lid anticlockwise to remove it and take out the desiccant bag [desiccant bag] from the inner box under the lid.
3. Pull up along the notches to remove the tank [food tank].
4. Twist the tank base anticlockwise to remove it.
5. Thoroughly rinse and air dry [air dry] the lid, tank, and tank base.
6. Refit them to the machine. Turn the tank base clockwise until it snaps into place.
7. Then install the tank and lid.

Clean the Bowls and Holder

1. Remove the bowl holder [bowl holder] from the feeder base.
2. Rinse the stainless steel bowls [stainless steel bowls] and holder, and air dry [air dry] them thoroughly before refitting.

Specifications

Troubleshooting

For assistance with common issues, consult the table below. If problems persist, contact the Customer Care Center at support@petlibro.com.