Product Information
PETLIBRO Granary Automatic Pet Feeder
Model: PLAF005 & PLAF006
©Libro Corp. All Rights Reserved.
Manufacturer: Shenzhen Libro Technology Co., Ltd.
Address: Building 3, Cloud Park, Shenzhen, China, 518129
Made in China
Document Version: PLAF005&006_V1.0
Compliance Information:
RoHS Compliant ✅ CE Certified ✅ FCC Certified ✅ UKCA Certified ✅ CAN ICES-3 (B)/NMB-3(B) Compliant ✅
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This user manual only applies to PETLIBRO Granary Automatic Pet Feeder with one bowl. Read and save the manual.
Safety Guidelines
⚠️ WARNING
- Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation; keep away from children and pets.
- Do NOT allow small children to play with, in or around the pet feeder.
- To reduce the risk of injury, please keep close supervision when an appliance is used near children.
- Do NOT use the feeder with pets not able to reach the food tray or with any physical disability.
- Do NOT immerse the base part in water at any time as it may damage electronic components like the control panel.
- Do NOT place any foreign object in the pet feeder.
- Do NOT use outdoors. Check operation frequently to be sure the unit is dispensing properly.
- Do NOT use wet, canned or moist food.
- Do NOT disassemble the unit other than as instructed in this User Guide.
- Do NOT use the feeder for anything other than its intended use.
- Only use attachments recommended or sold by the manufacturer. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do not modify the pet feeder.
- Do not operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the pet feeder yourself. Contact the customer service immediately for further instructions.
- Always unplug when not in use and before cleaning.
- Never pull on the electrical power cord to remove the plug from the wall outlet.
- If the plug of this device gets wet, turn on electricity to that wall outlet. Do not attempt to unplug.
- Examine the feeder after installation. Do not plug in if there is water on the power cord or plug.
- To avoid tripping, always position power cord out of the way of foot traffic.
❗ CAUTION
- Do NOT allow pets to chew on or swallow any parts. If there is concern about the power cord, purchase a cord conduit (a hard-plastic protector) at any hardware store to protect the power cord.
- If an extension cord is necessary, one unit with a proper rating should be used.
- Do NOT install or store the pet feeder where it will be exposed to weather or temperatures below 4°C / 40°F.
- Use alkaline D batteries to power. Do NOT use rechargeable batteries.
- Check the batteries regularly. Before leaving for extended time, always replace batteries with new ones.
- Do NOT lift the pet feeder by lid, food tank, or food tray. Lift and carry it using both hands and the base, while keeping the unit in an upright position.
- Suitable for dry food ONLY, with kibble size ranging from 2-15mm / 0.07-0.6in in diameter. Larger kibble may get stuck at the food outlet.
- Do not put fingers into the food outlet or let fingers touch the rotor.
- Read and observe all important notices listed on the pet feeder and in the packaging.
In The Box
The PETLIBRO Granary Automatic Pet Feeder package includes:
- 1 x Automatic Pet Feeder (main unit, cylindrical with a transparent window for food level, and a control panel at the base)
- 1 x Food Bowl with Holder (a shallow bowl with a separate base for stability)
- 1 x Power Adapter (a standard power brick with a cable)
- 1 x User Guide Kit (documentation)
- 1 x Desiccant Bag (a small packet for moisture absorption)
Visual description: The components are shown separately. The automatic pet feeder is a tall, cylindrical unit. The food bowl is a wide, shallow dish. The power adapter is a typical wall plug with a cord. The user guide is represented by a small booklet icon. The desiccant bag is a small rectangular packet.
Product Overview
The PETLIBRO Granary Automatic Pet Feeder consists of several key components:
- Lid: The top cover of the feeder.
- Seal Strip: A gasket located under the lid to maintain freshness.
- Food Tank: The main container for storing dry pet food.
- Transparent Window: A clear section on the food tank to view the food level.
- Tank Base: The lower part of the food tank assembly.
- Anti-Clog Detector: A mechanism to prevent food blockages (located near the food outlet).
- Control Panel: The interface with buttons for operating the feeder.
- Display Panel: The screen showing time, meal settings, and other information.
- Food Outlet: Where the food dispenses from the tank into the bowl.
- Feeder Base: The main structural base of the feeder.
- Stainless Steel Bowl: The removable bowl for pet food.
- Bowl Holder: The base that supports the stainless steel bowl.
- Desiccant Box: A compartment under the lid for the desiccant bag.
- Power Jack: The port for connecting the power adapter.
- Power Adapter: The external power supply unit.
- Battery Compartment: Located at the bottom of the feeder for backup batteries.
- Compartment Lid: The cover for the battery compartment.
- Speaker: For playing recorded meal calls.
Visual description: A detailed exploded diagram of the feeder shows each numbered component. The main unit is cylindrical, with the lid at the top, followed by the seal strip, food tank with a transparent window, and tank base. The anti-clog detector is shown as a small sensor near the food outlet. The control panel and display panel are on the front of the feeder base. The stainless steel bowl sits on the bowl holder at the bottom. A separate view shows the underside of the lid revealing the desiccant box, and the bottom of the feeder showing the power jack, battery compartment, and speaker.
How To Use
Assembly and Prepare for Setting
- Remove Components: Take out the food bowl from inside the food tank. Twist the lid anticlockwise to remove it. Pull up along the notches on either side to remove the food tank.
Visual description: Diagrams show the lid being twisted anticlockwise and lifted, then the food tank being lifted upwards from the base along its notches.
- Place Desiccant Bag: Place the desiccant bag into the inner box under the lid.
Notes:
- It is recommended to change the desiccant bag every 15 days to prevent mold growth.
- Remove the desiccant bag before cleaning the lid.
Visual description: A diagram shows a desiccant bag being placed into a small compartment on the underside of the lid.
- Install Food Tank: Align the food tank with the notches on both sides of the tank base and press down to secure.
Visual description: Diagrams show the food tank being lowered onto the feeder base, aligning with two vertical notches on the sides.
- Add Dry Pet Food: Add dry pet food to the food tank.
Notes:
- To prevent uneven food dispensing, add enough pet food to the visible level.
- Recommended kibble size: 2-15mm / 0.07-0.6 inch in diameter.
- Do not use canned, wet, or moist food.
Visual description: A diagram shows kibble being poured into the food tank. A measurement scale indicates the recommended kibble size (15mm). A line inside the tank indicates the "Minimum Grain Level".
- Replace Lid: Put the lid back on. To snap into place, turn the lid clockwise from the right rotating sign to the left rotating sign.
Visual description: A diagram shows the lid being placed on top of the food tank and then twisted clockwise to lock it into position, indicated by an arrow moving from an unlocked padlock symbol to a locked padlock symbol.
- Install Food Bowl: Attach the bowl to the designated notches underneath the feeder base.
Note: Before moving the feeder, press the bowl down to remove it from the feeder base. If there is grain in the food bowl, handle it gently to avoid spilling. Hold the base instead of any other parts when lifting the feeder.
Visual description: A diagram shows the food bowl being slid into place underneath the feeder base, indicated by an upward arrow.
- Connect Power:
- Plug the 5V power adapter into a power socket and the USB cable into the USB port on the back of the feeder.
- The LED display will light up automatically to indicate the feeder is on.
- Open the battery compartment at the bottom of the feeder. Install three alkaline D batteries (not included) in case of a power outage. Ensure the batteries match the positive and negative poles with the markings in the compartment.
- After the batteries are installed, the battery icon will light up on the screen; when the icon turns red and flashes, it means the battery level is low and the batteries need replacing.
Notes:
- Batteries are not included.
- To avoid sudden power outage and feeding disruption, do not use the batteries as the only power source. Batteries are for emergency backup only.
- To avoid battery leakage, remove the batteries if the device will not be used for some time.
Visual description: Diagrams show the power adapter being plugged into the back of the feeder and into a wall outlet. Another diagram shows the battery compartment at the bottom of the feeder, indicating where three D batteries are inserted.
Program Setting
- Set the Current Time: Pay attention to the 12-hour AM/PM format. Time will change from AM to PM automatically according to the setting.
Time Chart of 12-hour Format:
| AM | PM |
|---|
| 01:00 AM | 01:00 PM |
| 02:00 AM | 02:00 PM |
| 03:00 AM | 03:00 PM |
| 04:00 AM | 04:00 PM |
| 05:00 AM | 05:00 PM |
| 06:00 AM | 06:00 PM |
| 07:00 AM | 07:00 PM |
| 08:00 AM | 08:00 PM |
| 09:00 AM | 09:00 PM |
| 10:00 AM | 10:00 PM |
| 11:00 AM | 11:00 PM |
| 12:00 PM | 12:00 AM |
- Press and hold the ? Unlocked Button for 3 seconds to unlock other buttons and the screen. The ⏰ Current Time Setting Icon on the screen flashes, indicating it has entered setting mode.
- Press the ⚙️ Setting Button; the hour digits will flash.
- Use the ➕/➖ Increase/Decrease buttons to set the current hour, then press the ⚙️ Setting Button to save and move to the minutes setting.
- The tens digits of the minute will flash. Press the ➕/➖ Increase/Decrease buttons to set the tens digit first and press the ⚙️ Setting Button to save. Then set the single digit and press the ⚙️ Setting Button to save. The current time setting is complete.
Note: The control buttons and the screen will be locked automatically after 1 minute of standby.
Visual description: Diagrams show the display panel with flashing hour and minute digits during time setting, illustrating the progression of setting the time.
- Set the Time and Portion of Meals:
Set the time of the first meal:
- After the current time is set, the feeder enters feeding plan setting mode. The icon "1" will flash, indicating it is ready for settings of the first meal.
- Press the ⚙️ Setting Button to set the feeding time of the first meal. The hour digits will flash.
- Press the ➕/➖ Increase/Decrease buttons to set the hour. Then press the ⚙️ Setting Button to save and move to the minutes setting.
- The tens digits of the minute will flash. Press the ➕/➖ Increase/Decrease buttons to set the tens digit first and press the ⚙️ Setting Button to save. Then set the single digit and press the ⚙️ Setting Button to save.
Set the portion of the first meal:
Once the first meal time is set and saved, the feeder enters portion setting mode. The screen will display "P-XX", standing for portions.
- Press the ➕/➖ Increase/Decrease buttons to set the portions (Max 50). Set the tens digit first and press the ⚙️ Setting Button to save, then set the single digit and press the ⚙️ Setting Button to save.
- Repeat the steps above to set the time and portion for other meals if needed. The feeder supports up to 6 scheduled meals per day.
Note: The default feeding time for the first four meals is 6:00 AM, 12:00 PM, 6:00 PM, 12:00 AM, and the time for the fifth and sixth meal is 1:00 AM. The default portion is 0. These presettings can be changed.
Visual description: Diagrams show the display panel indicating meal number "1" flashing, then showing "P-01" for portion setting, and then "P-XX" for setting the portion amount.
- Record a Meal Call:
- In the unlocked state, press the ? Record Button once; a beep will be heard.
- Speak and record a message (maximum record time is 10 seconds). Press the ? Record Button again to end; two beeps will be heard indicating the recording is saved.
- The recording will automatically play once for checking the recorded voice.
Notes:
- The default meal call playback is 2 times, and the meal call will play when feeding time is due.
- The meal call does not play during manual feeding, only at each designated meal.
Visual description: A diagram shows a hand pressing the record button on the control panel, with a speech bubble indicating recording.
- Set the Times the Meal Call Plays: The meal call playback times can be set from 0-5. If set to zero, the meal call will not play at the corresponding meal.
- In the unlocked state, press and hold the ? Record Button for 3 seconds. The record icon will be on and the meal icon "1" will keep flashing.
- Press the ➕/➖ Increase/Decrease buttons to choose the number of meals to set, then press the ⚙️ Setting Button once to save.
- The screen will display "F-XX", standing for playback times. Press the ➕/➖ Increase/Decrease buttons to set the times the meal call plays, then press the ⚙️ Setting Button to save.
- Repeat the steps above to set the number of times the meal call plays for other meals.
Note: After all settings are complete, press and hold the ⚙️ Setting Button for 3 seconds to return to the locked interface.
Visual description: Diagrams show the display panel indicating "F-02" for setting playback times.
- Manually Feeding Your Pet:
In the unlocked state, press the ?️ Manual Feeding Button once; the feeder dispenses one portion of food. The manual feeding button can be pressed at most 5 times, dispensing up to 5 portions of food.
Note: The normal schedule and portion are not affected by manual feeding.
Visual description: A diagram shows a hand pressing the manual feeding button on the control panel, with food dispensing into the bowl.
- Clear All Settings:
Press and hold the ➕/➖ Increase/Decrease buttons simultaneously for 6 seconds until the machine emits three beeps. All icons on the screen will light up, indicating the resetting is complete.
Visual description: A diagram shows a hand pressing both the plus and minus buttons simultaneously on the control panel, with an 'X' symbol indicating reset.
Clean and Care
It is recommended to clean the feeder regularly for the health of pets.
The washable parts are: lid, food tank, tank base, stainless steel bowl, and bowl holder. Clean other parts with a dry cloth.
Clean the Tank Lid, Food Tank, Tank Base
Before removing the food tank, ensure it is empty to prevent food spilling.
- Disconnect Power: Unplug the feeder before cleaning.
Visual description: A diagram shows the power adapter being unplugged from the feeder.
- Remove Lid and Desiccant Bag: Twist anticlockwise to remove the lid and take out the desiccant bag from the inner box under the lid.
Visual description: Diagrams show the lid being twisted anticlockwise and lifted, and the desiccant bag being removed from its compartment.
- Remove Tank: Pull up along the notches to remove the tank.
Visual description: A diagram shows the food tank being lifted upwards from the base along its notches.
- Remove Tank Base: Twist anticlockwise to remove the tank base.
Visual description: A diagram shows the tank base being twisted anticlockwise and separated from the main unit.
- Rinse and Air Dry: Thoroughly rinse and air dry the lid, tank, and tank base.
Visual description: Diagrams show water droplets indicating rinsing, and sun rays indicating air drying for the lid, tank, and tank base.
- Refit Tank Base: Refit the tank base to the machine. Turn the tank base clockwise until it snaps into place.
Visual description: A diagram shows the tank base being twisted clockwise to lock it into position, indicated by an arrow moving from an unlocked padlock symbol to a locked padlock symbol.
- Install Tank and Lid: Then install the tank and lid.
Visual description: A diagram shows the food tank being lowered onto the base, and then the lid being placed on top.
Clean the Food Bowl
- Remove Food Bowl: Press down the food bowl with its holder to remove them.
Visual description: A diagram shows the food bowl being pressed down and then pulled away from the feeder base.
- Rinse and Air Dry: Rinse and air dry them thoroughly before refitting them to the machine.
Visual description: Diagrams show water droplets indicating rinsing, and sun rays indicating air drying for the food bowl and holder.
Specifications
Model PLAF005
| Model | PLAF005 |
| Capacity | 3 liters |
| Screen | LED screen |
| Power | DC 5V power adapter; 3 x alkaline D batteries (not included) |
| Power Adapter | AC100-240V Input, DC 5V output |
| Operating Temperature | 0°C - 55°C / 32°F - 131°F |
| Dimensions | 28 x 19 x 19 cm / 11 x 7.5 x 7.5 in |
| Net Weight | 1.5 kg / 3.3 lbs |
Model PLAF006
| Model | PLAF006 |
| Capacity | 5 liters |
| Screen | LED screen |
| Power | DC 5V power adapter; 3 x alkaline D batteries (not included) |
| Power Adapter | AC100-240V Input, DC 5V output |
| Operating Temperature | 0°C - 55°C / 32°F - 131°F |
| Dimensions | 34.6 x 19 x 19 cm / 13.6 x 7.5 x 7.5 in |
| Net Weight | 1.64kg / 3.6lbs |
Troubleshooting
The answers to these questions should help resolve most problems with the pet feeder. If issues persist, please contact PETLIBRO Customer Care Center via support@petlibro.com.
| Problem | Solution |
|---|
| I forget the meal settings. | - The number of the meals that have been set will show on the locked interface (not shown if not set).
- In the unlocked state, press the ➕/➖ Increase/Decrease button to choose the meal number to check, then press the ⚙️ Setting button to check the settings.
|
| The food won't come out. | - Ensure the food in the tank is dry, and food size is within 2-15 mm / 0.07-0.6 inches in diameter.
- Remove the food tank and tank base, check if the chute inside is blocked.
- Check if the anti-clog detector at the food outlet is dirty or blocked.
- Check whether the battery level is low, whether the power adapter is connected, and whether a power outage occurs when the power adapter is connected and batteries are not installed.
|
| "E1" shows on the screen and flashes. | - Remove any blockages at the food outlet.
- The anti-clog detector needs cleaning.
|
| LED display is off. | - Press and hold the ? Unlocked Button for 3 seconds to unlock the screen.
- Check whether the power adapter is connected.
- Contact the PETLIBRO support team at support@petlibro.com if the display still won't light up when the appliance is well connected to power.
|
| I can't remove the food tank. | Pull upwards along the notches on either side to remove the food tank. |
| The food amount of each portion is not the same. | The first few portions may vary, but it does not mean it is faulty. After about 6 feedings, it should be almost even. |
Warranty
PETLIBRO provides a 1-year warranty for this appliance. Customers can email the support team at support@petlibro.com for any questions, attaching their order ID in the email for prompt assistance.
For more information, please visit www.petlibro.com.
