Olight Seeker 3 Pro User Manual

IN THE BOX

Seeker 3 Pro (With Battery)

Holster

USB Magnetic Charging Cable

Lanyard Hole

PRODUCT OVERVIEW

Brightness Level Indicator: Indicates the current brightness level.

Battery Level Indicator: Shows the remaining battery power.

Magnetic Tailcap: Allows for magnetic attachment and charging.

Rotary Knob Brightness Controller: Used for adjusting brightness and mode selection.

SPECIFICATIONS

* All specifications are based on ANSI/NEMA FL1-2009 Standard, tested with the included battery. Maximum output brightness may decrease as battery voltage drops.

INDICATORS ON BOTH SIDES

Right Side Indicators:

• 5% < 5% (Red light indicates low battery)
• 10%
• 25% (10%~25%)
• 50% (25%~50%)
• 75% (50%~75%)
• 100% (75%~100%)

Note: When the flashlight is on, if the battery power is less than 10%, the lowest indicator on the right side will glow red.

AVAILABLE BATTERIES

1 x customized 5000mAh 21700 rechargeable lithium battery

BEFORE FIRST USE

1. Unscrew the tailcap and remove the insulating film within the battery compartment.
2. Screw the tailcap back on tightly.

Note: The flashlight arrives in lockout mode for shipping. To unlock, rotate the knob switch quickly over 90 degrees. The surrounding indicators will light up to confirm successful unlocking.

USB MAGNETIC CHARGING CABLE -- MCC3

Input: USB A - DC 5V 2A

Charging Pattern: CC&CV

Maximum Charging Current: 2A

Voltage of Fully Charged Battery: 4.2V ± 0.05V

Time to Fully Charge: Approximately 4.5 hours (with a 5V 2A power source).

Charge Indication: Red = Charging, Green = Fully Charged (over 95%) or disconnected.

Charging: Connect the magnetic USB end of the charging cable to a USB power source (5V 2A recommended for best efficiency) and attach the other end to the flashlight's charging port.

Attention:

• Keep the front lens clean to ensure the proximity sensor works correctly.
• Protect the front lens surface; scratches can reduce light output.
• Only use the standard MCC charging cable.

PROXIMITY PROTECTION FUNCTION

1. When the light is on at Level 3 brightness or higher, if the proximity sensor detects an obstruction, the brightness will automatically reduce. Stepless dimming is invalid in this state. Brightness restores when the obstruction is removed.
2. To disable the proximity sensor temporarily, quickly double-click (or triple-click) the knob switch within 5 seconds after the brightness automatically reduces. The light will enter the corresponding mode. Turning the light off will re-enable the proximity sensor.

OPERATING INSTRUCTIONS

LOCKOUT/UNLOCK:

The knob switch locks automatically if no operation is made within 30 seconds after the light is turned off. In lockout mode, a single click will not turn on the light but will show the battery level. To unlock, rotate the knob switch over 90 degrees; the indicators around it will light up for 3 seconds.

IN THE UNLOCKED STATE:

• ON/OFF: Single-click the knob switch. The light will return to the previously selected brightness level. (High mode and above are memorized as High. Other modes are memorized as they were. Medium mode and above are memorized as Medium after 1 minute of being off.)
• CHANGE BRIGHTNESS LEVEL: When the light is on, press and hold the knob switch. It will cycle through Low, Medium, and High modes. Release the switch to select the mode. (Moonlight and Turbo are not in this automatic cycle.)
• MOONLIGHT: When the light is off, press and hold the knob switch for over one second to access Moonlight mode.
• TURBO AND RETURN: Quickly double-click the knob switch to enter Turbo mode. Double-click again to return to the previous mode. (Medium mode and above are memorized as Medium.)
• STROBE: Quickly triple-click the knob switch to activate Strobe mode. Single-click or press and hold to exit.
• ROTATE CLOCKWISE (STEPLESS INCREASING): When the light is on, rotate the knob switch clockwise to ramp up the brightness to the maximum allowed. The brightness level indicator will flash when the maximum brightness is reached.
• ROTATE COUNTERCLOCKWISE (STEPLESS DECREASING): When the light is on (not in Moonlight mode), rotate the knob switch counterclockwise to decrease brightness to the lowest level. The brightness level indicator will flash when the minimum brightness is reached. Rotating counterclockwise in Moonlight mode will not change the mode.
• TIMER: The Seeker 3 Pro has a long (9 minutes) and short (3 minutes) timer for automatic shut-off. When the light is on, double-click and hold the knob switch at the current brightness level to access timer settings. A single blink selects the short timer; two blinks select the long timer. The light will automatically turn off when the timer expires.

SAFETY PRECAUTIONS

DANGER

• DO NOT shine the light directly into human eyes. This may cause temporary blindness or permanent damage.
• Keep out of reach of children.
• DO NOT cover the flashlight when it is on. Heat buildup can cause nearby objects to burn or result in disasters.
• DO NOT use a rechargeable battery without a protection board or if it is damaged.
• DO NOT immerse the flashlight in seawater or other corrosive media, as it can damage the charging port.
• DO NOT use other chargers to charge the customized battery; it may cause damage.

WARNING

• DO NOT repeatedly activate high mode in high temperatures to prevent the flashlight body from overheating and causing burns.
• Keep the charging port clean and dry before charging and maintain it regularly.
• If the battery needs replacement, store it carefully away from conductive metal.
• If the light will be stored or transported for a long time, unscrew the tailcap and remove the battery to disconnect the circuit.

NOTICE

• The light will automatically dim if it overheats to protect the user's hands.

EXCLUSION CLAUSE

Olight is not liable for damages or injuries sustained from usage inconsistent with the warnings in this manual, including usage inconsistent with the recommended lockout mode.

WARRANTY

• Within 30 days of purchase: Contact the original seller for repair or replacement.
• Within 5 years of purchase: Contact Olight for repair or replacement.
• Battery warranty: Olight offers a one-year warranty for all rechargeable batteries.
• MCC magnetic USB charging cable: One year.
• For fragile or low-value fittings (like lanyard and clip) not covered above, contact after-sales support within 30 days of purchase for quality issues under normal use. For issues occurring after 30 days or under abnormal use, conditional quality assurance will be offered.

CUSTOMER SUPPORT

• USA Customer Support: cs@olightstore.com
• Global Customer Support: Customer-service@olightworld.com
• Visit www.olightworld.com to see the complete product line.
• EU-Declaration of Conformity can be found here: https://olightworld.com/ec-declaration

MANUFACTURER INFORMATION

Dongguan Olight E-Commerce Technology Co., Ltd

4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.

Made in China