SIEMENS RTLS4083T RTLS Transponder Instruction Manual

Instruction Manual for SIEMENS models including: RTLS4083T RTLS Transponder, RTLS4083T, RTLS Transponder, Transponder

SIMATIC RTLS4083T

US

Siemens AG

Manual

Siemens Aktiengesellschaft 4083T02 SCF4083T02 SCF4083T02 4083t02

File Info : application/pdf, 30 Pages, 1.49MB

GetApplicationAttachment.html?id=7114469

SIMATIC RTLS Localization systems SIMATIC RTLS4083T
Operating Manual

Introduction

Device description

Installation & operation

Technical specifications

Approvals

02/2024
C79000-G8976-C646-06

Legal information
Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
DANGER indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION indicates that minor personal injury can result if proper precautions are not taken.
NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage.
Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems.
Proper use of Siemens products Note the following:
WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG Digital Industries Postfach 48 48 90026 NÜRNBERG GERMANY

C79000-G8976-C646-06 09/2023 Subject to change

Table of contents

1 Introduction ........................................................................................................................................... 5

2 Device description ................................................................................................................................. 9

2.1

Characteristics ..................................................................................................................... 9

2.2

Order data for RTLS4083T and accessories............................................................................ 9

2.3

LED status indicator, display & function key ........................................................................ 10

2.4

Dimension drawing of RTLS4083T...................................................................................... 11

2.5

Dimension drawing of RTLS charging station ...................................................................... 12

2.6

Dimension drawing of RTLS4083T mounting clip................................................................ 13

2.7

Dimension drawing of RTLS4083T Power mounting clip...................................................... 14

3 Installation & operation....................................................................................................................... 15

3.1

Notes on installation .......................................................................................................... 15

3.2 3.2.1 3.2.2

Operation .......................................................................................................................... 17 RTLS4083T operation......................................................................................................... 17 RTLS4083T operation with Power mounting clip................................................................. 18

3.3

Cleaning and maintenance................................................................................................. 18

3.4

Charging instructions for the RTLS charging station ............................................................ 18

4 Technical specifications ....................................................................................................................... 21

4.1

RTLS4083T technical specifications..................................................................................... 21

4.2

RTLS charging station technical specifications..................................................................... 22

4.3

Technical specifications of the mounting clip RTLS4083T .................................................... 23

4.4

Technical specifications of the RTLS4083T Power mounting clip .......................................... 23

5 Approvals ............................................................................................................................................. 25

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Table of contents

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Introduction

Purpose of the operating instructions
These operating instructions support you when installing and connecting the SIMATIC RTLS4083T transponder.
The configuration and the integration of the transponders in a network and the programming of the programming interface are not described in these operating instructions. For more information, refer to the section "Export module "ExportEpaperAPI"" in the "SIMATIC RTLS Data Export Service" document.

Scope of validity of the operating instructions These operating instructions apply to the following transponders and the associated accessories: · RTLS4083T (CE; article number: 6GT2700-5DC05) · RTLS4083T (FCC/NOM/ANATEL; article number: 6GT2700-5DC15)

Further documentation
You can find the complete documentation for all SIMATIC RTLS products at the following address: Link: (https://support.industry.siemens.com/cs/us/en/ps/25277)

Trademarks

The following and possibly other names not identified by the registered trademark sign ® are registered trademarks of Siemens AG:
SIMATIC RTLS

Industry Online Support
In addition to the product documentation, the comprehensive online information platform of Siemens Industry Online Support offers support at the following Internet address: (https:// support.industry.siemens.com/cs/start?lc=en-US)
Apart from news, there you will also find:
· Project information: Manuals, FAQs, downloads, application examples etc.
· Contacts, Technical Forum
· The option submitting a support query: (https://support.industry.siemens.com/My/us/en/)
· Our service offer: Right across our products and systems, we provide numerous services that support you in every phase of the life of your machine or system - from planning and implementation to commissioning, through to maintenance and modernization.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Introduction

You will find contact information on the Internet at the following address: (https:// www.automation.siemens.com/aspa_app/?ci=yes&lang=en)
SITRAIN Training for Industry
The training offer includes more than 300 courses on basic topics, extended knowledge and special knowledge as well as advanced training for individual sectors - available at more than 130 locations. Courses can also be organized individually and held locally at your location.
You will find detailed information on the training curriculum and how to contact our customer consultants at the following Internet address: (https://new.siemens.com/global/en/ products/services/industry/sitrain/personal.html)
RTLS Technology and Practice (ID-RTLS-TP)
Training and certification
After completing the RTLS certification training, you will be able to plan and implement small and medium-sized RTLS projects and provide efficient and multifaceted support in large projects. Your RTLS basics will be strengthened and, building upon them, you will receive new tools of the trade in order to offer customers the optimal solution for them. The complete project sequence is taken as a reference and important steps, resources and work results for each phase are presented. Comprehensive practical exercises in connection with troubleshooting techniques and a great deal of input from industrial projects allow you to internalize a confident approach to working with different types of localization projects. With the training documents, you also receive extensive reference material for your daily work.
Link: (https://www.sitrain-learning.siemens.com/EN/en/rw35251/Industrielle-IdentifikationRTLS-Technologie-und-Praxis)
Cybersecurity notes
Siemens provides products and solutions with industrial cybersecurity functions that support the secure operation of plants, systems, machines, and networks.
In order to protect plants, systems, machines, and networks against cyber threats, it is necessary to implement and continuously maintain a holistic, state-of-the-art industrial cybersecurity concept. Siemens' products and solutions form one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems, machines and networks. Such systems, machines and components should only be connected to an enterprise network or the internet if and to the extent such a connection is necessary and only when appropriate security measures (e.g. firewalls and/or network segmentation) are in place.
For more information on industrial cybersecurity measures that may be implemented, please visit: (https://www.siemens.com/global/en/products/automation/topic-areas/industrialcybersecurity.html)
Siemens' products and solutions undergo continuous development to make them more secure. Siemens strongly recommends performing product updates as soon as they are available and using only the latest product versions. Use of product versions that are no longer supported, and failure to apply latest updates may increase customer's exposure to cyber threats.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Introduction
To stay informed about product updates, subscribe to the Siemens Industrial Cybersecurity RSS Feed under: (https://new.siemens.com/global/en/products/services/cert.html)

Note on firmware/software support Check regularly for new firmware/software versions or security updates and apply them. After the release of a new version, previous versions are no longer supported and are not maintained.
Security recommendations
General Note the following security recommendations to prevent unauthorized access: · Keep the firmware up to date. Check regularly for security updates for the device. You can
find information on this at the Industrial Security (https://new.siemens.com/global/en/ company/topic-areas/future-of-manufacturing/industrial-security.html) website. · Inform yourself regularly about security recommendations published by Siemens ProductCERT (https://new.siemens.com/global/en/products/services/cert.html). · Evaluate your plant as a whole in terms of security. Use a cell protection concept with suitable products. · This product requires an additional security concept to prevent unauthorized access. · Transponder and infrastructure can be configured for radio channels according to IEEE 802.15.4-2015. You will find details in the section "Technical specifications". · Ensure that the radio frequencies are not used for other purposes and are not affected by other interfering signals. This should be ensured within the operating range of the localization system. · Interference in the frequency band used can impair the system and, in extreme cases, lead to localization failure.
Physical access · Restrict physical access to the device to qualified personnel. · Disable unused physical interfaces of the device. Unused interfaces could be used to gain
access to the operating site.
Recycling and disposal The products are low in harmful substances, can be recycled and meet the requirements of the Directive 2012/19/EU for disposal of waste electrical and electronic equipment (WEEE). Do not dispose of the products at public disposal sites. For environmentally compliant recycling and disposal of your electronic waste, please contact a company certified for the disposal of electronic waste or your Siemens representative.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Introduction Note the different national regulations.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Device description

2.1

Characteristics

SIMATIC RTLS4083T

Characteristics Design

General
1

2 3

Status indicator L1 (LED) Function key F1 Display
The transponder is a mobile device for localiza- tion in the RTLS localization system. It sends po- sition data to gateways which transmit the data to the Locating Manager server.
Information can be transmitted to the transpond- er via a programming interface on the Locating Manager and shown on the display.

2.2

Order data for RTLS4083T and accessories
Table 2-1 RTLS4083T order data

SIMATIC RTLS4083T

CE FCC/NOM/ANATEL

Article number 6GT2700-5DC05 6GT2700-5DC15

Table 2-2 Accessories order data (not included in product package)
SIMATIC RTLS charging station for 10 transponders with power supply unit and power plug for region: EU SIMATIC RTLS charging station for 10 transponders with power supply unit and power plug for region: USA Charging cradle without power supply unit for 10 transponders Power supply unit for charging cradle without power plug Power plug for region: EU Power plug for region: USA SIMATIC RTLS mounting clip for RTLS4083T (10 units) SIMATIC RTLS Power mounting clip for RTLS4083T (1 unit)

Article number 6GT2790-0DD02
6GT2790-0DD03
6GT2790-0DD20 6GT2790-0DD40 6ES7900-0AA00-0XA0 6ES7900-0DA00-0XA0 6GT2790-0DE30 6GT2790-0DE40

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Device description 2.3 LED status indicator, display & function key

2.3

LED status indicator, display & function key
The operating states of the transponder are indicated by the LEDs. The states can be off , on and flashing .

Table 2-3 LED status indicator

LED

Meaning

Lights up green once for 1.5 seconds when the transponder is restarted.

Briefly flashes green once when the F1 function button is pressed, the battery voltage is sufficient and the transponder is outside of the charging station or the Power mounting clip.
Continuously flashes green when the transponder is fully charged and in the charging station or the Power mounting clip.
Lights up green when the transponder is fully charged and in the charging station or the Power mounting clip.
Briefly flashes red once when the F1 function button is pressed, the battery voltage is low and the transponder is outside of the charging station or the Power mounting clip. However, the transponder is available and localizable.
Flashes red (user LEDs flash) if you trigger flashing via the Locating Manager. You can config- ure the duration and frequency of flashing via the Locating Manager.
Note that error states may not be detected by the user LED flashing.
Continuously flashes red when the transponder is in the charging station or the Power mount- ing clip and the battery is defective.
Remove the transponder from the charging station or the Power mounting clip immediately and do not recharge this transponder. Contact customer service.
Lights up red if there is an error during charging.

Note
Observe the notes in sections "RTLS4083T operation (Page 17)" and "Charging instructions for the RTLS charging station (Page 18)".

Table 2-4 Display and function key

Display Display
F1 function key

Meaning
5 background images can be saved
20 text fields with 58 characters each
20 fonts and font sizes, including bar codes
If this function key is pressed, the message is forwarded to the program interface.
When the F1 function button is pressed, the charge state of the battery is evaluated and, depending on its voltage, the LED briefly flashes green or red. In the Locating Manager, you can configure a transponder parameter to define the threshold value below which the battery voltage is defined as too low for operation, a "low power" message is generated and the LED flashes red. Refer to the notes in the section "RTLS4083T operation (Page 17)".

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Device description 2.4 Dimension drawing of RTLS4083T

2.4

Dimension drawing of RTLS4083T

6,0$7,& / 57/67

)

Figure 2-1

Dimension drawing of SIMATIC RTLS4083T - All dimensions are given in millimeters

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Device description 2.5 Dimension drawing of RTLS charging station

2.5

Dimension drawing of RTLS charging station

Figure 2-2 Dimension drawing of SIMATIC RTLS charging station (not included with the product) - All dimensions are given in millimeters

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Device description 2.6 Dimension drawing of RTLS4083T mounting clip

2.6

Dimension drawing of RTLS4083T mounting clip

Dimension drawing of SIMATIC RTLS mounting clip for RTLS4083T (not included with the product) - All dimensions are given in millimeters

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Device description 2.7 Dimension drawing of RTLS4083T Power mounting clip

2.7

Dimension drawing of RTLS4083T Power mounting clip

Figure 2-3 Dimension drawing of SIMATIC RTLS Power mounting clip for RTLS4083T (not included in product package) - All dimensions are given in millimeters

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Installation & operation

3.1

Notes on installation
Note Before you install the transponders, read this section carefully to ensure problem-free installation and commissioning.
The transponders can only be used in conjunction with the RTLS localization system. Install the transponder in such a way that it has a direct line-of-sight connection to the gateways (360° panorama view). Any type of material can impact wireless localization. Wireless localization through metal is not possible. In this case, localization via wireless reflections can occur which results in an inaccurate localization. Check the transponder for damage before installation. Protect the display from objects that could scratch or otherwise damage it. The specified operating temperature ranges must be observed. The transponder contains one lithium ion battery.
CAUTION Contact with the battery fluid Incorrect handling of the transponder may damage the battery and cause fluid to leak out of the battery. Avoid contact with the battery fluid. Rinse skin that comes into contact with battery fluid with water. If fluid from the battery gets into the eye, seek medical attention.
CAUTION Handling batteries There is a risk of fire and, in extreme cases, of explosion in the following cases: · If the battery is improperly charged and discharged · If the polarity is reversed · If a short-circuit occurs This applies to lithium-ion batteries: · Do not squeeze · Do not heat and do not burn · Do not short-circuit · Do not disassemble · Do not immerse in liquid - the battery may crack or burst

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Installation & operation 3.1 Notes on installation
CAUTION Fires and burns Improper handling of the battery can lead to fire and skin injuries.
The enclosure of the transponder must not be squashed, punctured or exposed to other mechanical influences. Never expose the transponder to fire, temperatures above 40 °C or direct sunlight for an extended period of time.
Reflections and interferences The antenna fields are weakened by absorbing materials and reflected by conducting materials. When electromagnetic fields are reflected or there are other radio sources, this will result in interferences. These circumstances will result in incorrect measurements; however, these can be largely detected and corrected with the appropriate software (e.g. SIMATIC RTLS Locating Manager). We still recommend that you prevent these influences. Especially objects that cannot be penetrated by radio waves can cause localization errors.
Note Metal surfaces reflect radio waves more than any other types of surfaces. Water, on the other hand, attenuates radio waves. You should therefore evaluate your working environment and integration for these influences. During installation, pay attention to sufficient distance from such reflective surfaces so that localization is not impaired.
Coexistence and de-sensing To prevent interfering with each other, radio applications will use different frequency bands. Use of these frequency bands is subject to state regulation. Because a frequency range is considered a finite good, technologies were developed over the years that enable a coexistence of different radio applications in the same frequency band. These technologies are also used by SIMATIC RTLS. However, interferences can still be caused by other radio devices. Arrangements are being made here, too, so that these interferences do not impact the operation of the RTLS localization system. To keep interferences to a minimum, the RTLS infrastructure components must not be installed in the close vicinity of other radio applications. Strong senders in close vicinity can interfere with the reception, even when they are located in neighboring frequency bands (desensing). This is true, for example, for the 2.4 GHz ISM band and PULSE in the UWB channel 5.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Installation & operation 3.2 Operation
Installation with Power mounting clip
NOTICE Observe general installation instructions Observe the general installation instructions for the transponder described above this paragraph.
The Power mounting clip is only intended for vertical installation, so that the contacts of the Power mounting clip are at the bottom. Installation can be performed as described in section "Technical specifications of the RTLS4083T Power mounting clip (Page 23)". Only operate the Power mounting clip with a suitable power supply with the permissible values, see section "Technical specifications of the RTLS4083T Power mounting clip (Page 23)". Use the lug at the bottom of the Power mounting clip to relieve the strain on the cables to the plug on the left of the Power mounting clip.

3.2

Operation

3.2.1

RTLS4083T operation
Note Operate the transponder only with the accessories intended for this purpose, which are listed in the section "Order data for RTLS4083T and accessories (Page 9)".
The transponder is delivered in the switched-off state. To commission the transponder, it has to be inserted into the associated charging station or Power mounting clip once so that the green LED on the device lights up. The transponder is operated with the F1 function key on the front panel. The function of the key can be programmed via the programming interface. If the voltage is too low, the transponder switches off automatically and sends a "Low-Power" message to the Locating Manager. The limit above which the transponder sends this message is configurable. In this case, the transponder must be fully recharged within 3 months to avoid deep self-discharge and damage to the battery.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Installation & operation 3.4 Charging instructions for the RTLS charging station

3.2.2

RTLS4083T operation with Power mounting clip

Note
Operate the transponder only with the accessories intended for this purpose, which are listed in the section "Order data for RTLS4083T and accessories (Page 9)".

The transponder is delivered in the switched-off state. To commission the transponder, it has to be inserted into the associated charging station or Power mounting clip once so that the green LED on the device lights up. The mode of the transponder in the active clip behaves like operation in the charging station. There is no differentiation by the transponder or Locating Manager. This also includes charging of the battery like in the charging station. When the transponder is operated continuously in the active clip, the battery is regularly charged, with the transponder being supplied by the external supply voltage. The transponder is only charged if the ambient conditions as described in the sections "Charging instructions for the RTLS charging station (Page 18)" and "RTLS4083T technical specifications (Page 21)" are met.

3.3

Cleaning and maintenance
The enclosure of the transponder must not be opened. The devices specified in this document may only be repaired or opened for other types of work by an authorized maintenance company. Improper opening or repairing of the devices may result in serious risks for the user. Opening the devices without permission renders the warranty of the Siemens AG null and void. Do not clean the devices with liquids or abrasive, caustic or flammable cleaning products.
Note Due to the integrated battery, the RTLS4083T transponder is a hazardous good. Observe the applicable regulations when shipping.

3.4

Charging instructions for the RTLS charging station

Mount the charging station in a location with cool ambient temperature. Then, fully charge the transponder using the charging station.

The temperature of the transponder and the ambient temperature must not exceed 40 °C for the transponder to be charged. The higher the temperature, the longer it takes to charge the transponder.

If the transponder exceeds 55 °C during charging, remove the transponder from the charging station. Allow the transponder to cool down and try charging it again. If the transponder becomes too hot again, remove the transponder from the charging station and contact customer service.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Installation & operation
3.4 Charging instructions for the RTLS charging station
The battery has a natural self-discharge. When stored in a state not fully charged, the transponder is discharged after approximately 6 months and must be recharged. If the transponder is completely discharged, the integrated battery may be damaged.
To charge, insert the transponder fully in a charging bay of the charging station. The front of the transponder must face away from the side of the cable guide. The start and status of the charging process are signaled via the LED display on the transponder. A full charging process takes approximately 8.5 hours. To ensure correct operation of all 10 charging bays and to avoid damage to the transponders, only use the power supply unit provided with the charging station.
Read also the descriptions of the operating states of the transponder in section "LED status indicator, display & function key (Page 10)".

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Installation & operation 3.4 Charging instructions for the RTLS charging station

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Technical specifications

4.1

RTLS4083T technical specifications

Table 4-1 Technical specifications of the transponder RTLS4083T

Product name

SIMATIC RTLS4083T

6GT2700-5DC05, 6GT2700-5DC15

PULSE radio frequencies (localization) Wireless method Transmission speed Operating frequency rated value
Bandwidth Frequency range
Transmit power Range Accuracy of the localization (typical) Antennas

IEEE 802.15.4-2015 UWB HRP PHY 850 Kbps 3993.6 MHz (UWB channel 2; CE, FCC, NOM, ANATEL) 6489.6 MHz (UWB channel 5; CE) 499.2 MHz 3100 MHz ... 4800 MHz (CE, FCC, NOM, ANATEL) 6000 MHz ... 7000 MHz (CE) 0.037 mW (-41.3 dBm/MHz) Maximum 30 m 0.1 m Built-in UWB antenna

PHASE radio frequencies (communication and optional localization)

Wireless method

IEEE 802.15.4

Transmission speed

1 Mbit/s

Operating frequency rated value

2405 MHz ... 2480 MHz

Bandwidth

2 MHz; data transmission on 802.15.4; channels configurable

Frequency range

2400 MHz ... 2483.5 MHz

Transmit power

0.00025 mW ... 4 mW (configurable)

Range

Maximum 50 m

Accuracy of the localization (typical)

3 m

Antennas

Built-in 2.4 GHz antenna

Supply voltage Supply voltage Service life (at 20 )

3.7 V lithium ion rechargeable battery (1950 mAh) Standby: 1 year Operation: 100% UWB localization at 1 second: 6 months Display updates every 10 seconds without localization: 25 days

Permitted ambient conditions

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Technical specifications 4.2 RTLS charging station technical specifications
Ambient temperature · During storage · During transport · During operation · During display operation · During charging
Design, dimensions, weights and connectors Dimensions (L x W x H) Weight Degree of protection Fastening method Enclosure Color

6GT2700-5DC05, 6GT2700-5DC15
· -10 °C ... +50 °C · -10 °C ... +50 °C · -10 °C ... +50 °C · 0 °C ... +40 °C · +10 °C ... +40 °C
95 mm x 64,6 mm x 13,8 mm 85 g IP65 Mounting clips Plastic enclosure Titanium gray

4.2

RTLS charging station technical specifications

Table 4-2 Technical specifications of the SIMATIC RTLS charging station (not included in the product package)

Product name Power supply unit Input voltage of RTLS charging station Power loss of RTLS charging station

6GT2790-0DD02, 6GT2790-0DD03 SIMATIC RTLS charging station 110 V ... 220 V 5 V DC 25 W

Permitted ambient conditions of RTLS charging station Ambient temperature · During storage · During transport · During operation

· -10 °C ... +50 °C · -10 °C ... +50 °C · See Permitted ambient conditions of the RTLS4083T trans-
ponder

Design, dimensions, weights and connectors of RTLS charging station Dimensions (L x W x H) Weight Degree of protection Enclosure Color

298.4 mm x 180.6mm x 83.2 mm 1092 g IP00 Plastic enclosure (PC 10 GF) Titanium gray

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Technical specifications 4.4 Technical specifications of the RTLS4083T Power mounting clip

4.3

Technical specifications of the mounting clip RTLS4083T

Table 4-3 Technical specifications of the RTLS4083T mounting clip (not included in product package)

Product name Material Color Permitted ambient temperature · During storage · During transport · During operation Dimensions (L x W x H) Weight Fastening method
Verification of suitability

SIMATIC RTLS mounting clip for RTLS4083T Plastic, PC GF10 Titanium gray

6GT2790-0DE30

· -10 ... +55 °C · -10 ... +55 °C · See Permitted ambient conditions of the RTLS4083T transponder 100.6 x 71.1 x 22 mm; tolerances according to DIN 16742-TG5 29 g 4 x screws (max. Ø 3.5 mm) with washers (not included in product package) Ensure that the screw head does not damage the transponder. CE

4.4

Technical specifications of the RTLS4083T Power mounting clip

Table 4-4 Technical specifications of the RTLS4083T Power mounting clip (not included in product package)

Product name Material Color Permitted ambient temperature · During storage · During transport · During operation
Dimensions (L x W x H) Weight
Fastening method
Type of power supply
Supply voltage Rated voltage Power consumption

SIMATIC RTLS RTLS4083T Power mounting clip Plastic, PC GF10 Titanium gray

6GT2790-0DE40

· -25°C ... +75 °C · -25°C ... +75 °C · See Permitted ambient conditions of the RTLS4083T transponder during charg-
ing 116 x 87 x 22.5 mm; tolerances according to DIN 16742-TG5 44 g (without plug) 45 g (with plug) 4 x screws (max. Ø 3.5 mm) with washers (not included in product package) Ensure that the screw head does not damage the transponder. 1 x "Phoenix" plug (included in product package) 2 x cables with cross-section 1 mm2 and wire end ferrules with at least 10 mm length (not included in product package) Make sure to observe the polarity marked on the Power mounting clip. 19 ... 25 V DC 24 V DC Maximum 8 W

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Technical specifications 4.4 Technical specifications of the RTLS4083T Power mounting clip

Current consumption Verification of suitability

Maximum 0.3 A CE

6GT2790-0DE40

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Approvals

Country-specific approvals
All the latest radio approvals for RTLS devices are available on the Internet (https:// support.industry.siemens.com/cs/de/de/view/109784340).
If a device has one of the following marks, the corresponding approval has been obtained.

Labeling

Description Australia/New Zealand

South Africa (ICASA) Independent Communications Authority of South Africa, Sandton Radio Equipment Type Approval Certificate
United Arab Emirates TRA
EAC (Eurasian Conformity) Eurasian Economic Union of Republic of Armenia, the Republic of Bela- rus, the Republic of Kazakhstan, the Kyrgyz Republic and the Russian Federation Declaration of conformity according to the technical regulations of the customs union (TR CU) USA (FCC) This device complies with part 15 of the FCC rules.

Alternative: FCC ID: XXXXYYZZZZ IC: XXXXYYZZZZ

Canada (ISED)
This device complies with Industry Canada licence-exempt RSS stand- ard(s).

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Approvals

Labeling
Alternative: ANATEL: XXXXYYZZZZ

Description
Brazil (ANATEL)
Certificado de Homologação
REPÚBLICA FEDERATIVA DO BRASILAGÊNCIA NACIONAL DE TELECOMU- NICAÇÕES
Este equipamento não tem direito à proteção contra interferência prej- udicial e não pode causar interferência em sistemas devidamente autor- izados. Para maiores informações, consulte o site da ANATEL (www.ana- tel.gov.br).
Importer UK:
Siemens plc, Sir William Siemens House, Princess Road, Manchester M20 2UR

CMIIT ID: XXXXYYZZZZ

Mexico (NOM)
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia per- judicial y (2) este equipo o dispositivo debe aceptar cualquier interfer- encia, incluyendo la que pueda causar su operación no deseada.
China (CMIIT)
Radio Transmission Equipment Type Approval Certificate
In accordance with the provisions on the Radio Regulations of the Peo- ple's Republic of China, the following radio transmission equipment, after examination, conforms to the provisions with its CMIIT ID.
South Korea (KCC)
Korea Communications Commission Certificate of Broadcasting and Communication Equipments
Republic of Korea

Note The specified approvals apply only when the corresponding mark is printed on the product. You can check which of the following approvals have been granted for your product by the markings on the type plate.
You can find the current EU Declaration of Conformity for these products on the Internet at Siemens Industry Online Support. Link: (https://support.industry.siemens.com/cs/de/en/ps/25277/cert)

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Approvals
The products described in this document meet the requirements of the following EU directives:
· RoHS Directive 2011/65/EU Directive of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment, official journal of the EU L174, 1 July 2011, pages 88-110
· Radio Equipment Directive 2014/53/EU (RED) Directive of the European Parliament and of the Council of 16 April 2014 on the harmonization of the laws of the member states relating to placing radio equipment on the market; official journal of the EU L153, 22 May 2014, pages 62-106
UK Declaration of Conformity The UK declaration of conformity is available to all responsible authorities at:
Siemens Aktiengesellschaft Process Industries and Drives Division, Process Automation DE-76181 Karlsruhe Germany
Importer UK:
Siemens plc, Manchester M20 2UR
You can find the current UK Declaration of Conformity for these products on the Internet pages under Siemens Industry Online Support (https:// support.industry.siemens.com/cs/en/en/view/109801531).
The SIMATIC RTLS products described in this document meet the requirements of the following directives/regulation:
· Radio Equipment Regulations: SI 2017/1206 Radio Equipment Regulations 2017, and related amendments
· RoHS Regulations: SI 2012/3032 Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, and related amendments
RoHS directive (restriction of the use of certain hazardous substances) The products described in these operating instructions meet the requirements of the EU directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
Applied standard:
· IEC 63000 Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances
The products described in this document meet the requirements of the applied standards:

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Approvals
Article 3 (1) a) Protection of health and safety
· EN 62368-1 Equipment for audio/video, information and communication technology Part 1: Safety requirements
· EN 62311 Assessment of electronic and electrical equipment related to human exposure restrictions in electromagnetic fields (0 Hz - 300 GHz)
The products described in these operating instructions meet the requirements of EU directive 2014/30/EU "Electromagnetic Compatibility" according to the designated standards for the following areas of application.
Article 3 (1) b) EMC
· ETSI EN 301 489-1 Electromagnetic compatibility and radio spectrum matters (ERM) - Electromagnetic compatibility for radio equipment and services - Part 1: Common technical requirements
· ETSI EN 301 489-17 Electromagnetic compatibility and radio spectrum matters (ERM) - Electromagnetic compatibility for radio equipment and services - Part 17: Specific conditions for broadband data transmission systems
· ETSI EN 301 489-33 Electromagnetic compatibility and radio spectrum matters (ERM) - Electromagnetic compatibility for radio equipment and services - Part 33: Special conditions for ultra-wideband (UWB) devices
· EN 55011 Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics Limits and methods of measurement
· EN 55032 Class A, Class B Electromagnetic compatibility of multimedia equipment Emission requirements
· EN 55035 Electromagnetic compatibility of multimedia equipment - Immunity requirements
· EN 61000-6-1 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for residential, commercial and light-industrial environments
· EN 61000-6-2 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments
· EN 61000-6-3 Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments
· EN 61000-6-4 Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Approvals
Article 3 (2) Efficient use of the radio spectrum · ETSI EN 300 328 Wideband transmission systems; Data transmission equipment operating in the 2.4 GHz ISM band and using wide band modulation techniques. Harmonized standard covering the essential requirements of article 3.2 of the EU Directive 2014/53/EU · ETSI EN 302 065-2 Short Range Devices (SRD) using ultra-wideband technology (UWB); Harmonized standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 2: Requirements for UWB location tracking
FCC information Siemens SIMATIC RTLS4083T (MLFB 6GT2700-5DC15); FCC ID SCF4083T02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC RF radiation exposure statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 7 mm between the radiator and your body. The device must be carried with the display side facing away from the body. It should be installed and operated with a minimum distance of 7 mm from the antenna to the surface, whereby these 7 mm lie within the device.
NOTICE FCC Regulations §15.521 - Technical requirements applicable for all UWB devices. (a) UWB devices may not be employed for the operation of toys. Operation onboard an aircraft, a ship or a satellite is prohibited.

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

Approvals
EAC (Eurasian Conformity) Eurasian Economic Union of Republic of Armenia, the Republic of Belarus, the Republic of Kazakhstan, the Kyrgyz Republic and the Russian FederationDeclaration of conformity according to the technical regulations of the customs union (TR CU)

NOM información Siemens SIMATIC RTLS4083T (MLFB 6GT2700-5DC15); IFT RCPHMR22-2325 La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

ANATEL

Siemens SIMATIC RTLS4083T (MLFB 6GT2700-5DC15); ANATEL 00731-21-09908
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Para maiores informações, consulte o site da ANATEL (www.anatel.gov.br)

SIMATIC RTLS4083T

Operating Manual, 02/2024, C79000-G8976-C646-06

References

Antenna House PDF Output Library 7.2.1790; modified using iTextSharp 5.0.2 (c) 1T3XT BVBA