Ninja Kitchen System Pulse™ BL208Q Series Owner's Guide
Your comprehensive guide to operating and maintaining your Ninja Kitchen System Pulse.
Important Safety Instructions
For Household Use Only
- To protect against electrical shock, do not submerge the appliance or allow the power cord to come into contact with water or any other liquid.
- DO NOT allow young children to operate the appliance or use as a toy. Close supervision is necessary when any appliance is used by or near children.
- Never leave an appliance unattended when in use.
- Remove the power cord from the electrical outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the electrical outlet. Never pull from the power cord.
- DO NOT abuse the power cord. Never carry the appliance by the power cord or yank it to disconnect from electrical outlet; instead grasp the plug and pull to disconnect.
- DO NOT operate any appliance with a damaged cord or plug, or after the appliance malfunctions, has been dropped or damaged in any manner. Return the appliance to EURO-PRO Operating LLC for examination, repair or adjustment.
- DO NOT let the power cord hang over the edge of table or counter or touch hot surfaces such as the stove.
- Always use appliance on a dry, level surface.
- Keep hands, hair, clothing, as well as utensils out of container while processing to reduce the risk of severe injury to persons or damage to the appliance. A scraper may be used but only when the appliance is not running.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. DO NOT modify the plug in any way.
- Blade assembly is sharp, handle with care. When handling the blade assembly, always hold by the shaft or collar.
- Avoid contact with moving parts.
- DO NOT attempt to sharpen blades.
- DO NOT use the appliance if blade assembly is bent or damaged.
- To reduce risk of injury, never place the blade assembly on the base without the bowl properly attached.
- DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a heated oven).
- The use of attachments or accessories including canning jars, not recommended by the manufacturer may result in fire, electric shock or personal injury.
- DO NOT remove the container from the motor base while the appliance is in operation.
- To reduce the risk of injury, NEVER operate the appliance without the lid in place; DO NOT try to defeat the interlock mechanism; make sure that the attachment is properly installed before operating the appliance.
- DO NOT expose containers to extreme temperature changes.
- DO NOT blend hot liquids.
- DO NOT overfill.
- DO NOT operate the appliance empty.
- When mixing pizza dough or any heavy mix such as bread dough or pastry dough, mix for up to 1 minute, then let the appliance rest for approximately 1 minute before mixing again to prevent overheating of the appliance.
If the appliance overheats, a thermal switch will become activated and shut off the motor. To reset, unplug the appliance and let it cool down for approximately 30 minutes before using again.
THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use this appliance for anything other than its intended use. Do not use outdoors.
The maximum rating is based on the Cookie Paddle (40 oz. bowl) that drives the greatest power and other recommended attachments may draw less power or current.
Keep the pour spout closed when blending to prevent splashing.
Save These Instructions
Product Information
Model Numbers Covered:
- BL208QBK 30
- BL208QBL 30
- BL208QCN 30
- BL208QR 30
Technical Specifications:
| Specification | Value |
|---|---|
| Voltage | 120V., 60Hz. |
| Power | 700 Watts |
| Bowl Capacity | 40 ounces (5 cups) |
| Single Serving Cup Capacity | 16 ounces (2 cups) |
Euro-Pro, Ninja and Ninja Kitchen System Pulse are trademarks of Euro-Pro Operating LLC.
Contents
- Getting to Know Your Ninja® Kitchen System Pulse™
- Assembling the Ninja® Kitchen System Pulse™
- Assembly and Use for the Single Serve Cup
- Assembly and Use for the 40-oz Bowl
- Assembly and Use of the Shredding/Slicing Disc Bowl
- Suggested Uses
- Care & Maintenance
- Troubleshooting Guide
- Recipes
- Warranty
Diagram showing the various components of the Ninja Kitchen System Pulse, including the motor base, 40-oz bowl, single serve cups, blade assemblies, lids, and the shredding/slicing disc.
Getting To Know Your Ninja® Kitchen System Pulse™
The Ninja® Kitchen System Pulse™ is a high powered innovative tool with a compact design and outstanding performance. It is perfect for ice crushing, chopping, blending, and complete juicing. Blend and go with the convenient single serve cup, create delicious drinks to get you out the door! Best results are achieved when you Pulse.
Diagram illustrating the various parts of the Ninja Kitchen System Pulse, labeled A through N:
- a Food Pusher
- b To-Go Single Serve Lids (x2)
- c Storage Lid
- d Lid with Locking Handle
- e Slicer/Shredder Lid for 40-oz. Bowl
- f Single Serve Drink Cups (x2)
- g Shredding/Slicing Disc
- h 4-Blade Assembly (40-oz. bowl)
- i Spindle (40-oz. bowl)
- j Single Serve Blade
- k 40-oz. Bowl
- l Drive Gear
- m Motor Base
- n Power Cord (not shown)
NOTE: Attachments are not interchangeable.
Features:
- Ninja® Blade Technology
- 40 oz. Bowl and Single Serve Drink Cup - BPA Free
- Cord storage
- Pulse Power: Controlled blending, processing, juicing, and kneading by using short pulses. In short intervals, press down on the top of the single serve drink cup or the handle of the lid and pulse to the perfect consistency.
- Single Serve Blending: Fill, blend, and go! Blend right in the single serve drink cup and twist on the to-go lid for a healthy, convenient snack with little clean up.
- For best results, be sure to carefully read all the instructions contained in the manual before using this appliance.
Assembling the Ninja® Kitchen System Pulse™
- ⚠IMPORTANT: Always place the attachment in the 40-oz. bowl before adding any ingredients.
- ⚠IMPORTANT: Attachments are not interchangeable.
- ⚠CAUTION: Blades are sharp! Use extreme caution when handling the blade assemblies. Always hold them by the shaft.
- ⚠IMPORTANT: Never run the appliance empty.
- ⚠CAUTION: Never attempt to remove the container while the appliance is still running.
- ⚠WARNING: Never leave the appliance unattended while in use.
Before First Use:
- Remove all packaging material and labels from the appliance.
- Wash the lids, bowl, single serve cups and attachments in warm, soapy water with a soft cloth. Use caution when washing the blade assemblies as the blades are very sharp.
- Rinse and dry thoroughly.
- The bowl, single serve cups, lids and attachments are all dishwasher safe. It is recommended that the lids and attachments be placed on the top rack. Ensure that the attachments are removed from the containers before placing in the dishwasher.
- Wipe the motor base clean with a damp cloth.
Assembly and Use for the Single Serve Cup
For best results, use short “PULSES”... Practice makes perfect!!
Diagrams illustrating the assembly, pulsing action, and removal of the single serve cup. Figure 1 shows the blade assembly being screwed onto the cup. Figure 2 shows the assembled cup being inverted and locked onto the motor base. Figure 3 shows a hand pressing down on the cup to activate pulsing. Figure 4 shows the cup being turned counter-clockwise for removal. Figure 5 shows the cup being lifted straight up from the motor base.
- Place the motor base on a clean, dry, level surface such as a counter or table top.
- Add ingredients to the single serve cup.
- Place the single serve blade onto the cup and screw it tightly until you have a good seal. (Refer to Figure 1 in the diagram).
- Turn the single serve cup upside down and place it onto the motor base, aligning the tabs on the cup with the motor base. Turn clockwise until the unit locks in place, the unit is ready for use. (Refer to Figure 2 in the diagram).
- Press down on the top of the cup in short intervals to activate. (Refer to Figure 3 in the diagram).
- When you have reached your desired consistency, stop the appliance by removing your hand from the single serve cup. Then turn the single serve cup counter clockwise (Refer to Figure 4 in the diagram) and pull straight up to remove. (Refer to Figure 5 in the diagram).
NOTE: Do not overfill! To avoid spilling, do not add ingredients past the “Max” fill line.
- Turn the cup upright and remove the single serve blade by twisting the blade assembly to the left.
- Place the To-Go drinking lid onto the single serve drink cup, twist to seal and enjoy!
- Make sure that the motor base is unplugged when not in use.
Assembly and Use for the 40-oz. Bowl
It's best to add the liquid ingredients first and then the dry ingredients.
Diagrams illustrating the assembly, pulsing action, and removal of the 40-oz bowl. Figure 1 shows the bowl being placed and locked onto the motor base. Figure 2 shows the blade assembly being inserted into the bowl. Figure 3 shows the lid being placed and locked onto the bowl. Figure 4 shows a hand pressing down on the lid handle to activate pulsing. Figure 5 shows the lid handle being pulled up for removal. Figure 6 shows the bowl being turned counter-clockwise and lifted off the motor base.
- Place the motor base on a clean, dry, level surface such as a counter or table top.
- Align and lower the bowl onto the motor base. (Refer to Figure 1 in the diagram) Handle should be aligned slightly to the left of the "LOCK" symbol on the motor base.
- Rotate the container clockwise as far as it will go to lock in place. (Refer to Figure 1 in the diagram).
- Holding the desired attachment by the shaft, place it onto the drive gear inside the container. Ensure that the attachment is seated properly and is standing upright. (Refer to Figure 2 in the diagram).
NOTE: The blade will fit loosely on the drive gear.
- Add the ingredients to the bowl, making sure that they do not exceed the highest measured marking line on the side of the bowl.
- Holding the lid by the handle in the upright position, place it on top of the bowl aligning the arrow (✔) located on the lid with the arrow (▲) located on the bowl's handle. (Refer to Figure 3 in the diagram).
- Push down on the "PULSE" on the handle to start the appliance. (Refer to Figure 4 in the diagram).
NOTE: Pulse ingredients for even chopping by pressing down in short intervals.
- When you have reached your desired consistency, stop pressing the lid handle and wait for the attachment to stop turning.
- To remove the lid, pull the lid handle up to a 90° angle. Turn the bowl counter clockwise to lift off the base. (Refer to Figure 5, Figure 6 in the diagram).
- Make sure that the unit is unplugged when not in use.
Assembly and Use of the Shredding/Slicing Disc with the Bowl
Diagrams illustrating the assembly and use of the shredding/slicing disc. Figure 7 shows the spindle being inserted into the bowl. Figure 8 shows the shredding/slicing disc being placed onto the spindle. Figure 9 shows the lid with feeder tube being placed on the bowl. Figure 10 shows food being pushed through the feeder tube with the on/off switch engaged.
- Place the motor base on a clean, dry, level surface such as a counter or table top.
- Align and lower the bowl onto the motor base. Handle should be aligned slightly to the left of the "LOCK" symbol on the motor base.
- Rotate the container clockwise as far as it will go to lock in place.
- Insert the spindle into the bowl. (Refer to Figure 7 in the diagram).
- Hold the disc by the plastic hub and carefully place the shredding/slicing disc onto the spindle. (Refer to Figure 8 in the diagram).
- Holding the lid by the feeder tube, place it on top of the bowl aligning the on/off switch with the bowl's handle. (Refer to Figure 9 in the diagram).
- Place food into the feeder tube. Using the food pusher, add food through the feeder tube. Push the on/off switch forward to the "On" position. (Refer to Figure 10 in the diagram).
- When you have finished slicing or shredding, release the on/off switch to turn the appliance off. Wait for the disc to stop turning and then remove the lid.
- Hold the shredding/slicing disc by the hub to remove and then remove the spindle. Empty the food from the bowl.
- The spindle, shredding/slicing disc, lid and food pusher are all top rack dishwasher safe.
Suggested Uses
| Function | Container | Attachment | Type of Food |
|---|---|---|---|
| Mincing | Single Serve 40-oz. Bowl | Blade Assembly | Onion, Garlic, Herbs |
| Blending | Single Serve 40-oz. Bowl | Blade Assembly | Smoothies, Milkshakes, Frozen Drinks, Dips, Spreads |
| Grating | Single Serve 40-oz. Bowl | Blade Assembly | Cheese, Bread Crumbs |
| Chopping | 40-oz. Bowl | Blade Assembly | Salsa, Vegetables, Egg Salad |
| Ice Crushing | Single Serve 40-oz. Bowl | Blade Assembly | Ice, Slushies, Snow Cones |
| Complete Juicing | Single Serve 40-oz. Bowl | Blade Assembly | Fruit & Vegetable Drinks |
Care & Maintenance
How to Clean:
- Separate/remove all parts from each other.
- Clean the motor base and gear shaft with a damp cloth and wipe dry.
- Place the bowl and single serve cups in the dishwasher. Place the lids and attachments on the top rack. Use caution when handling the blade assemblies as the blades are very sharp.
NOTE: You may also wash the containers by filling the container with no more than 24-oz. of warm water and a drop of dish washing detergent, placing the corresponding lid on the container and pulsing a few times. Do not fill the container with more than 24-oz. of water because it will overflow. Once clean, remove the container from the motor base. Rinse the container, attachment and lid under running water. Allow all the parts to dry before storing.
How to Store:
- Store the Ninja® Kitchen System Pulse™ upright with the 40-oz bowl on the motor base, 4-Blade assembly inside and lid on the bowl. Secure the power cord underneath the base by wrapping the cord around the cord wrap. Do not place anything on top. Store the single serve cups and the rest of the attachments along side the appliance where they will not be damaged and won't cause a hazard.
Resetting the Motor Thermostat:
The Ninja® Kitchen System Pulse™ features a unique safety system which prevents damage to the unit's motor and drive system should you inadvertently overload your appliance. If the appliance is being overloaded, the motor will stop. To reset the appliance, follow the resetting procedure below:
- Unplug the appliance from the electrical outlet.
- Remove and empty the container and ensure that no food is jamming the cutting blades or attachments.
- Allow the appliance to cool for approximately 30 minutes.
- Re-install the container onto the base and re-plug the appliance into the electrical outlet.
- Proceed to use the appliance as before making sure not to exceed the recommended maximum capacities.
Troubleshooting Guide
| Problems | Possible Reasons & Solutions |
|---|---|
| Motor Doesn't Start or Attachment Doesn't Rotate. |
|
| Food is Unevenly Chopped. |
|
| Food is Too Finely Chopped or Too Watery. |
|
| You Cannot Achieve Snow From Ice Cubes. |
|
| Single serve cup is leaking. |
|
| Unit doesn't turn on. |
|
| Unit doesn't turn off. |
|
| Doesn't mix well. |
|
Recipes
Breakfast Smoothie
Ingredients:
- 1/2 Banana
- 2 Frozen Strawberries
- 1/4 Cup Blueberries
- 1 Cup Orange Juice
- 3 Ice Cubes
Directions:
- Add the ingredients, in the order listed above, into the single serve cup.
- Screw on the single serve cup blade lid, screwing the lid on tightly.
- Place the single serve cup on to the motor base (see assembly instructions).
- Push down on the top of the single serve cup to begin blending. Run until smooth. Serve immediately.
Serves 1. Use Single Serve Cup.
Quick Orangesicle
Ingredients:
40 oz bowl:
- 1/2 Cup Fresh Orange Juice
- 1/2 Cup Fresh Red Grapefruit, Peeled, Segmented
- 1 Cup Fresh Orange, Peeled, Segmented
- 1 Cup Low Fat Plain Yogurt
- 1 tsp. Powdered Sugar
- 10 To 12 Ice Cubes
Single Serve:
- 1 Cup Vanilla Frozen Yogurt
- 1/4 Cup Orange Juice
- 1/2 Cup Fresh Orange, Peeled, Segmented
Directions:
Place all the ingredients in 40 oz. bowl or single serve cup and Pulse until smooth. Serve right away.
40 oz. bowl serves 4. Use 40 oz. Bowl or Single Serve cup.
Fire Roasted Tomato Salsa with Tortilla Chips
Ingredients:
- 14.5 oz. Can Fire-Roasted Tomatoes, With Juice
- 1/2 Small Red Onion, Peeled, Roughly Cut
- 4 Cloves Garlic Peeled
- 1/2 tsp. Salt
- 1/4 tsp. Black Pepper
- 1/4 tsp. Ground Cumin
- 1/4 Cup Cilantro Leaves
- 2 tbsp. Fresh Lime Juice
- 6 oz. Baked Tortilla Chips
Directions:
Place all ingredients in the 40 oz. bowl and pulse until fairly smooth. Taste and adjust seasonings, if desired. Serve right away with chips or refrigerate for up to 2 days.
Makes about 1 1/2 cups. Use 40 oz. Bowl with Bowl Lid.
Smoked Salmon Spread
Ingredients:
- 8 oz. Low Fat Cream Cheese, At Room Temperature
- 1/4 Cup Low Fat Sour Cream
- 1/4 Cup Low Fat Greek Yogurt
- 1 tbsp. Fresh Lemon Juice
- 2 tsp. Fresh Dill, Plus More For Garnish
- 2 tsp. Chives (Or Green Onions) Plus More For Garnish
- 1/2 tsp. Salt
- 1/4 tsp. Freshly Ground Black Pepper
- 8 oz. Smoked Salmon, Roughly Chopped Thinly Sliced Rye Bread Rounds
Directions:
Place the cream cheese, sour cream, yogurt, lemon juice, dill, chives, salt, pepper, and half of the smoked salmon in the 40 oz. bowl.
Pulse until smooth.
Place the spread in a serving dish and mix in the remaining salmon. Garnish with dill and chives, if desired. Serve right away with rye bread rounds or chill until serving.
Serves 8. Use 40 oz. Bowl with Bowl Lid.
One (1) Year Limited Warranty
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at their option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
If the appliance fails to operate properly while in use under normal household conditions within the Limited Warranty period, the complete appliance and accessories with proof of purchase and date, freight prepaid, may be returned. For Customer Service support, call 1-877-646-5288.
If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO-PRO Operating LLC's sole discretion, they will repair or replace it free of charge. Proof of purchase date and a check made payable to EURO-PRO Operating LLC in the amount of $19.95 to cover the cost of return shipping and handling must be included.*
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives specific legal rights, and other rights which vary from state to state or from province to province.
