PLATSA Assembly Instructions
IKEA Design and Quality
Important Safety Information
⚠️ WARNING!
Serious or fatal crushing injuries can occur from furniture tip over. To prevent tip over, this furniture must be used with the wall attachment device(s) provided.
Screw(s) and plug(s) for the wall are not included. Use screw(s) and plug(s) suitable for your walls. If you are uncertain, seek professional advice. Read and follow each step of the instruction carefully.
This warning is repeated in multiple languages throughout the document.
Assembly Steps
-
Step 1: Joining Panels
Two large side panels are shown. Insert dowels (part 151705) into the pre-drilled holes on one panel. Align the second panel with the dowels and push them together. Secure the connection by inserting and tightening a screw (part 151706) into the designated hole. An incorrect alignment is shown with a cross symbol [❌].
-
Step 2: Folding a Panel
A large panel is shown being folded or bent into shape.
-
Step 3: Attaching Side Panel
Attach another panel to the side of the previously folded panel. A close-up shows a screw (part 151706) being inserted and tightened into a pre-drilled hole.
-
Step 4: Inserting Back Panel
A long, thin panel is shown being slid into grooves or slots on the assembled frame. Close-ups illustrate the connection points.
-
Step 5: Securing the Base
Insert four screws (part 151705) into the bottom of the assembled frame, likely to attach feet or a base.
-
Step 6: Attaching Feet and Dowels
Attach two feet (part 150689) to the bottom of the frame using screws. Insert multiple dowels into the sides of the frame. A booklet titled "LÄTTHET" is shown, suggesting related accessories or further steps.
-
Step 7: Attaching Top Components
A completed cabinet frame is shown standing. Attach two circular components (part 150689) to the top edge of the frame using screws.
-
Step 8: Top Component Attachment
Similar to Step 7, showing the attachment of circular components (part 150689) to the top edge of the cabinet frame.
-
Step 9: Shelf Adjustment
A booklet titled "LÄTTHET" is shown. An illustration indicates adjusting the position of shelves within the cabinet frame using shelf pins or supports.
-
Step 10: Wall Attachment
Place the cabinet against a wall. Attach a wall anchoring component (part 10005905) to the top rear edge of the cabinet using a screw (part 126916). A "CLICK!" sound indicator is present. An incorrect attachment is shown with a cross symbol [❌].
-
Step 11: Connecting Multiple Units
If assembling multiple units, place them side-by-side. Use a connecting plate (part 10090922) to join two cabinet frames. Secure the plate using screws (part 146113) at designated numbered points (1-14) on the cabinet sides.
-
Step 12: Stacking Units
Stack one cabinet unit on top of another. A maximum stacking height of 300 cm (118 7/64") is indicated. Secure the top unit to the bottom unit using spring-loaded parts (part 152059) and screws (part 108736).
-
Step 13: Final Adjustments
A booklet titled "LÄTTHET" is shown again. A hand is depicted making a final adjustment to the top cabinet unit.
Parts List
The following parts are illustrated and quantified:
- 8x Dowels (Part 151705)
- 8x Screws (Part 151706)
- 4x Long Screws (Part 108736)
- 4x Plastic Components (Part 152059)
- 4x Spring-Loaded Components (Part 146113)
- 2x Round Caps (Part 10005905)
- 2x Washers (Part 126916)
- 2x Feet (Part 150689)
- 2x Bracket Assemblies (Part 150688)
- 2x Connecting Plates (Part 10090922)
General Advice
Always ensure furniture is securely attached to the wall to prevent tip-over accidents. Use appropriate wall fixings for your wall type. If unsure, consult a professional.
