Blooma Brant Motion Sensor Light

Important Safety Information

This is a combined document. Please ensure that the instruction manual and safety manual are split out and printed separately, including blank pages.

PLEASE DO NOT PRINT THIS PAGE.

These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.

• All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671).
• Check the pack and make sure you have all of the parts listed.
• Remove all packaging, wrap etc from the product.
• The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for "masonry" only. Other fixings not supplied and must be purchased.
• Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
• IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the light fitting.
• We recommend connecting this product to an external / wall switch in order to deactivate the motion detection function if necessary.
• Wiring diagram is for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.
• When the product does not light after installation: Ensure there is no electricity failure. Ensure all the connections are secured.
• If you have any doubt about installation/use of this product, consult a qualified electrician.
• It is recommended to have a regular schedule of care and maintenance to keep the surface condition well.

Technical Data

Warranty Period and Conditions

Blooma devotes special attention to selecting high-quality materials and uses manufacturing techniques that enable the creation of designer and durable product ranges. This product is offered with a 2-year warranty against manufacturing defects, valid for normal, non-professional household use from the date of purchase. The warranty is applicable upon presentation of the till receipt or invoice. Proof of purchase must be kept in a safe place.

The warranty covers product breakdowns and malfunctions when the product is used as intended, and installation and maintenance are performed according to good practice and the user manual. The product must be installed so it can be removed later without damage.

This contractual warranty does not cover defects and damage caused by:

• Natural wear and tear of parts.
• Adverse weather conditions, flooding, heat release, freezing.
• Water quality issues (hardness, aggressiveness, corrosion, etc.).
• Presence of foreign bodies in water (sand, filings, etc.).
• Lack of room ventilation.
• Improper use, misuse, negligence, accident, or defective maintenance not complying with good practice or the user manual.
• Consequences from using non-original or non-adapted accessories/spare parts, disassembly, or product modification.

The warranty is limited to parts recognised as defective and does not cover ancillary expenses (travel, labour) or direct and consequential damages. Guarantee-related queries should be addressed to the store where the product was purchased. This guarantee is in addition to and does not affect your statutory rights.

Installation Guide

The following steps detail the installation process. Ensure you have all parts listed before starting.

Step 01: Language Selection

Choose the appropriate language for installation instructions.

Step 02: Mounting the Sensor Unit

Attach the sensor unit [01] to the mounting bracket. This typically involves using screws [A] and wall plugs [A] if mounting into a wall.

Step 03: Wiring Connections

Connect the wires to the terminal block. Identify the terminals for Live (L), Neutral (N), and the switched Live output (Lout).

Step 04: Preparing Mounting Holes

Use a Ø6 mm drill bit to create mounting holes in the wall. Insert wall plugs [A] into the prepared holes.

Step 05: Securing the Main Unit

Attach the main unit to the wall using screws [B] and the previously inserted wall plugs [A]. Ensure the unit is securely fastened.

Step 06: Final Wiring Connections

Complete the electrical connections to the terminal block, ensuring all wires are correctly seated and secured.

Step 07: Wire Identification

Refer to the colour coding for wiring: Typically, L (Live) is Brown or Red, and N (Neutral) is Blue or Black.

Step 08: Attaching the Sensor Housing

Connect the sensor housing to the main unit. This may involve aligning and clicking components into place.

Step 09: Angle Adjustments and IP Rating

The unit has an IP44 rating, meaning it is protected against splashing water. The sensor can be adjusted for detection angles, typically up to ≤30° vertically and 55° horizontally. Ensure the detection angles are set appropriately for the desired coverage.

Step 10: Powering On

Switch the power ON using the appropriate switch. The indicator lights will show the status.

Step 01 (Usage): Timer Adjustment

Adjust the 'TIME' dial to set the duration the light stays on after motion is detected. Options range from approximately 10 seconds to 4 minutes.

Step 02 (Usage): Sensor Sensitivity Adjustment

Adjust the 'SENS' dial to set the sensitivity of the motion sensor. This determines how easily the sensor detects movement. The diagram shows detection ranges from 1.8-2.5 meters up to 6 meters or 12 meters depending on the setting.

Step 03 (Usage): Lux (Light Sensitivity) Adjustment

Adjust the 'LUX' dial to set the ambient light level at which the sensor activates. Setting it towards the sun symbol (☀️) means it will only activate in low light or darkness. Setting it towards the moon symbol (?) means it will activate even in daylight.

Step 04 (Usage): Detection Range and Angle

This section illustrates the detection range and angle of the motion sensor. It typically covers a range of 1.8-2.5 meters in height and can detect motion up to 12 meters away, with a detection angle of 180°.

Step 05 (Usage): Activating Sensor Override Mode

To activate the sensor override mode (manual ON/OFF), turn the light switch OFF and then ON within approximately 3 seconds. The light will remain ON.

Step 06 (Usage): Deactivating Sensor Override Mode

To deactivate the sensor override mode and return to automatic operation, turn the light switch OFF and then ON again after more than 5 seconds. The sensor will revert to its automatic detection mode.

Step 01 (Care): Maintenance

Regular cleaning and maintenance are recommended to keep the surface in good condition. Avoid using harsh cleaning agents or abrasive materials that could damage the product's finish.

Manufacturer and Distributor Information

UK Manufacturer: Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX, United Kingdom

EU Manufacturer: Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands

For instruction manuals online, visit: www.kingfisher.com/products

Distributors:

• France: www.castorama.fr, www.bricodepot.fr
• Poland: www.castorama.pl
• Russia: ООО «Касторама РУС», www.castorama.ru
• Romania: www.bricodepot.ro
• Spain: www.bricodepot.es
• Portugal: www.bricodepot.pt
• Turkey: KOÇTAŞ YAPI MARKETLERİ TİC. A.Ş., www.koctas.com.tr

EAC Certification: Complies with the technical regulations of the Eurasian Customs Union.